Summary of the content on the page No. 1
Roof Curbs, Extensions and
Equipment Supports
August
2008
Summary of the content on the page No. 2
Page Roof Curbs Header & Extensions Prefabricated roof curbs reduce installation time and costs by ensuring compatibility between the fan, curb and roof opening. A wide variety of roof curbs are available including: flanged, straight-sided, canted, pitched, ridged, vented, and sound-absorbing. Extensions raise the fan discharge and can provide an accessible mounting location for dampers. Insect screen bases and vented extensions are also available. Quick Delivery and Quick Build Programs More
Summary of the content on the page No. 3
Model Page GPI Header Standard Construction Features INSUlATION - Ridged fiberglass insulation is standard on lAP JOINTS - Wood all GPI curbs. The insulation is securely attached at both the nailers attached to GPI top and bottom with an insulation tray so it will not have any curbs consist of notched exposed ends. Three pound density insulation is available in and lapped joints to ensure 1 1, 1 ⁄2, and 2-inch thicknesses. strength and durability. CONSTRUCTION - Curb sizes under FORMED
Summary of the content on the page No. 4
Page Roof Curbs Header Models GPI, GPIP and GPIR These curbs are designed for roof decks covered with 2 to 6 inches of insulation. Model GPI is for use on flat roofs, GPIP for pitched roofs and GPIR is available for ridged (double pitched) roofs. They are mounted directly to the roof deck before the insulation is applied, then roofed and flashed to the top of the wood nailer for weather tightness. Models GPI, GPIP and GPIR are standard with fully welded construction, 1-inch insulation and
Summary of the content on the page No. 5
Equipment Page Header Supports and Curb Extensions Models GESS and GESR These equipment supports are designed for use on both insulated (GESR) and non-insulated (GESS) flat roof decks. They are mounted directly to the deck structure, then roofed and flashed for weather tightness. A variety of sizes and widths are available. (Refer to CAPS for more details.) Models GESS and GESR are available in welded aluminum or galvanized steel. Available in heights of 8, 12 and 14 inches and widths of 4
Summary of the content on the page No. 6
Page Sound Header Curbs Model AT Sound Curbs are designed to reduce fan generated sound traveling down the ductwork without adversely affecting fan performance. Air passes between the streamlined baffles allowing the fan sound to be absorbed and dissipated within the curb area preventing it from entering the building. Each perforated aluminum baffle section is filled with fiberglass wool. Spring steel wire holding clips secure the aluminum baffle. The assembly is a rigid, durable section whi
Summary of the content on the page No. 7
Fan Curb Adapt Down 1.500 B A A Curb Dimensional Page Header Data Fan Curb Adapt Down 1.500 B A A Curb BASIC ADAPTER AND REDUCER ADAPTER DIMENSIONAl INFORMATION (Fan curb cap is smaller than existing curb) Curbs without wood nailers = Adapted REDUCER curb cap width and length will be Fan (Fan curb cap is larger 1/2-inch larger than the curb AD than existing curb) dimension. Curb Cap W & L Curbs with wood nailers = Adapted Fan Curb Cap W & L - 1/2 in. curb cap width and length will be 2 1/2
Summary of the content on the page No. 8
Typical Installation Greenheck's straight-sided roof curbs are designed for general exhaust or supply applications. General Flashed Roof Installation: 1. Remove roofing material where roof penetration is to be made and provide a 10-inch wide clearance around perimeter of hole in roof. 2. Apply roofing cement around roof opening. 3. Place and center roof curb over hole in roof so it sits on roofing cement. Make sure the roof curb is placed over an adequate support structure to handle the weig
