Summary of the content on the page No. 1
BATTERY CHARGER
WITH LCD DISPLAY
65834
SET uP AnD OPERATInG InSTRuCTIOnS
®
Distributed exclusively by Harbor Freight Tools .
3491 Mission Oaks Blvd., Camarillo, CA 93011
Visit our website at: http://www.harborfreight.com
Read this material before using this product.
Failure to do so can result in serious injury.
SAVE THIS mAnuAL.
© ®
Copyright 2008 by Harbor Freight Tools . All rights reserved. No portion of this manual or any artwork
contained herein may be reproduced in any shape or form
Summary of the content on the page No. 2
nOTICE is used to SAVE THIS mAnuAL address practices Keep this manual for the safety warn- not related to personal injury. ings and precautions, assembly, operating, CAuTIOn, without inspection, maintenance and cleaning pro- the safety alert cedures. Write the product’s serial number symbol, is used to address in the back of the manual (or month and practices not related to year of purchase if product has no num- personal injury. ber). Keep this manual and the receipt in a safe and
Summary of the content on the page No. 3
an increased risk of electric shock if adjustments, changing accesso- your body is grounded. ries, or storing the product. c. Do not expose this product to rain c. Store this product out of the reach or wet conditions. Water entering of children and do not allow per- this product will increase the risk of sons unfamiliar with this product electric shock. or these instructions to operate the unit. Electrically powered prod- d. Do not abuse the Power Cord. ucts are dangerous in the hands of
Summary of the content on the page No. 4
3. Do not start a vehicle or turn on a • Avoid operating alone. mobile unit when connected to the • Do not use with power switch locked Battery Charger. on. • Properly maintain and inspect to 4. When the battery is being charged in avoid electrical shock. the vehicle, verify that the ignition is • Any power cord must be properly off. Connect the positive (RED with grounded. Ground Fault Circuit Inter- +) Cable Clamp to the positive (+ or rupter (GFCI) should also be imple- P) termina
Summary of the content on the page No. 5
“live” terminal. GROunDInG (See 3-Prong Plug and Outlet.) TO PREVEnT 3. The tool must be plugged into an ELECTRIC SHOCK appropriate outlet, properly installed AnD DEATH FROm and grounded in accordance with all InCORRECT GROunDInG codes and ordinances. The plug and WIRE COnnECTIOn: outlet should look like those in the Check with a qualified preceding illustration. electrician if you are in doubt (See 3-Prong Plug and Outlet.) as to whether the outlet is properly grounded. Do not
Summary of the content on the page No. 6
least the minimum wire size required. PRODuCT SPECIFICATIOnS (See Table A.) 120 VAC / 60 Hz Power Cord: 18 AWG x 3C SVT Electrical Power Plug: 3-Prong, Non-Polarized 5. If you are using one extension cord Requirements Output Voltage: 14.4VDC Maximum for more than one tool, add the Output Current: 6 Amps Maximum nameplate amperes and use the sum 6VDC or 12VDC Lead-Acid Batteries Only. Product (3Ah to 48Ah Charger Capacity) to determine the required minimum Applications Indoor Use Only cord
Summary of the content on the page No. 7
4. Battery Selection: Press “6V or Display Features: 12V” for the battery type that is to be 1. Power Switch: Press “ON/OFF” charged. (See Figure A.) to start charging. Press “ON/OFF” 5. LCD Display of Battery: The LCD again to stop charging. will indicate the battery type (6V or (See Figure A.) 12V) that has been selected. (See 2. Charging Rate Selection: Press Figure A.) “AMPS SELECTION” button to set 6. LCD Display of Voltage: Before charging current. (See Figure A.) connec
Summary of the content on the page No. 8
3. If the battery is not 6 volt or 12 volt, or the battery is damaged, the LCD will display “E03”. (See Below.) 4. If the battery is in the process of charging, the LCD will display the fol- lowing: (See Below.) Battery Status 1. If the battery is not connected, the LCD will display the following: (See Below.) Sound Alarms: 1. A continuous “beep” indicates wrong polarity, disconnection during charg- ing, wrong type of battery, dead or improper battery connection. 2. If the battery is co
Summary of the content on the page No. 9
positive (+ or P) terminal of the bat- tery Charger will then turn to the next tery. Connect the negative (BLACK charging stage under constant volt- with --) Battery Clamp to an unpaint- age. ed, solid metal portion of the vehicle. If “AUTO” is selected, the Battery Do not connect to the carburetor or Charger starts charging from 2 Amps fuel lines. until the charging voltage is raised up to 7.2V volts for a 6 volt battery (mo- 4. After the Battery Clamps are con- torcycle) or up to 14.4V
Summary of the content on the page No. 10
(RED with +) Battery Clamp from the aclean, soft cloth for best perfor- positive (+ or P) terminal of the bat- mance. Do not use solvents, acid, or tery. alkali products. 3. Replace the battery caps on the bat- 4. WARnInG! If the Power Cord is tery. damaged, it must be replaced only by a qualified service technician. mAInTEnAnCE AnD PLEASE READ THE SERVICInG FOLLOWInG CAREFuLLY Procedures not specifically explained in this manual THE MANUFACTURER AND/OR must be performed only by a
Summary of the content on the page No. 11
TROuBLESHOOTInG Problem Display Possible Causes Possible Solutions Battery Charger 1. Screen is not 1. No AC power input. 1. Check the plug and power source. will not charge. turned on. The push buttons 1. Screen displays 1. The battery is not connected. 1. Check the battery connections. do not work. 00.0V. 2. Screen displays 2. The polarity connection is 2. Make sure the polarity is correct. E01. wrong. There is a 1. Screen displays 1. The battery is disconnected 1. Check the battery connectio
Summary of the content on the page No. 12
ASSEmBLY DIAGRAm SKU 65834 For technical questions, please call 1-800-444-3353. Page 12
Summary of the content on the page No. 13
LImITED 90 DAY WARRAnTY Harbor Freight Tools Co. makes every effort to assure that its products meet high quality and durability standards, and warrants to the original purchaser that this prod- uct is free from defects in materials and workmanship for the period of 90 days from the date of purchase. This warranty does not apply to damage due directly or indirectly, to misuse, abuse, negligence or accidents, repairs or alterations outside our facilities, criminal activity, improper installat
