Summary of the content on the page No. 1
Color GPS Chart Plotters
CP180/CP180i
CP300/CP300i
Owner's Manual
CP180/180i
CP300/300i
Summary of the content on the page No. 2
WARNING!!! Electronic charts displayed by the GPS Chart Plotter are believed to be accurate and reliable, but are not intended to be a substitute for the official charts, which should remain your main reference for all matters related to the execution of safe navigation. For this reason we would like to remind you that you should carry on board and use the official published and approved nautical charts. FCC Compliance Statement This device complies with Part 15 of the FCC limits for Class
Summary of the content on the page No. 3
CAUTION - The GPS Chart Plotter is designed for maritime use. To avoid water intrusion ensure the C-MAP C-CARD door is completely closed. - Extensive exposure to heat may result in damage to the GPS Chart Plotter. - The GPS Chart Plotter contains dangerous high voltage circuits which only experienced technicians can handle. - STANDARD HORIZON will not be liable for errors contained herein, or for incidental or consequential damages in connection with the performance or use of this material. CLEA
Summary of the content on the page No. 4
Page 6 GPS Chart Plotters
Summary of the content on the page No. 5
TABLE OF CONTENTS 1. INTRODUCTION ...................................................................................................... 11 1.0 GENERAL INFORMATION .................................................................................... 11 1.1 PACKING LIST ...................................................................................................... 11 1.1.0 CP180/CP180i Packing List ...................................................................... 12 1.1.1 CP300/CP300i
Summary of the content on the page No. 6
4.2 INFO ON LAKES .................................................................................................... 38 4.2.0 Quick Info On Lakes .................................................................................. 38 4.2.1 Full Info On Lakes ...................................................................................... 38 5. C-MAP MAX OVERVIEW ................................................................................................. 41 5.0 INSERTING THE C-CARD ...
Summary of the content on the page No. 7
12.0.2 Turning Off Information on Icon Points ..................................................... 69 12.0.3 Display Mode ............................................................................................. 69 12.0.4 Marine Settings .......................................................................................... 70 12.0.5 Depth Settings ........................................................................................... 71 12.0.6 Land Settings .........................
Summary of the content on the page No. 8
Page 10 GPS Chart Plotters
Summary of the content on the page No. 9
1. INTRODUCTION Congratulations on your purchase of the Standard Horizon GPS Chart Plotter. Whether this is your first GPS Chart Plotter, or if you have other STANDARD HORIZON equipment, the STANDARD HORIZON organization is committed to ensuring your enjoyment of this GPS Chart Plotter. STANDARD HORIZON technical support personnel stand behind every product we sell, and our Product Support team invites you to contact us should you require technical advice or assistance, at 800/767-2450, or marin
Summary of the content on the page No. 10
1.1.0 CP180/CP180i Packing List PART CODE ITEM S8002224A External bracket S8002225 Mounting knob with two washers S8002222 Dust cover T9101553 Power data cable S8002223 Flush mounting screws (CP180 ONLY) EM016N550 Flush mount template (CP180 ONLY) XUCMP0058 GPS WAAS Smart antenna EM023U100 Owner’s Manual EM023U500 Quick Reference Guide 1.1.1 CP300/CP300i Packing List PART CODE ITEM S8002224A External bracket S8002225 Mounting knob with two washers S8002235 Dust cover T9101553 PWR & ACC 1 cable T
Summary of the content on the page No. 11
2. GETTING STARTED NOTE Throughout this Owner’s Manual same conventions are used. See the legend below: [MENU]If you see brackets around a bold and capital letter word this refers to a key press. [CHART] If you see brackets around a bold and small capital letter word this refers to a Soft Key press. GENERAL SETUP When a word(s) is bold capital letters and underlined, this refers to a menu selection item. 2.0 MOUNTING THE GPS CHART PLOTTER The CP180 and CP300 are supplied with hardware for bracke
Summary of the content on the page No. 12
2.2 CP180 AND CP300 FLUSH MOUNTING The CP180 and CP300 are supplied with a flush mount template for the cutout hole and screw holes required to install the GPS Chart Plotter. NOTE Before drilling holes make sure there is enough room to mount the GPS Chart Plotter and there are no obstructions. 1. After a location is found, peel the template label from the backing and apply the label to the mounting area. 2. Drill a hole in one area of the cutout area that will allow the blade of a jig saw to be
Summary of the content on the page No. 13
Choose a location for the antenna that has a clear view of the sky and is not located within 3 FT of Radar or other transmitting antennas. Ensure there are no major obstructions or fixtures in the immediate proximity to the antenna. The antenna relies on direct “line of sight” satellite reception. If you are unsure of the chosen location, temporarily mount the antenna in the desired location to verify correct operation. If mounted close to Radar, after the GPS Chart Plotter has a fix, turn on th
Summary of the content on the page No. 14
2.4 CONNECTIONS The GPS Chart Plotter has connectors that are used to connect to the power supply, GPS Antenna (CP180 AND CP300 ONLY) optional FF520 50/200kHz BLACK BOX FISH FINDER and to NMEA devices such as VHF’s, AIS Receivers, digital instruments and autopilots. NOTE The GPS Chart Plotter can send many sentences to external NMEA devices. The NMEA Output wires are Yellow, Brown and White. If you have connected devices as shown in the below table and need to feed NMEA to other devices (Autopil
Summary of the content on the page No. 15
5. Move the ShuttlePoint knob up/down to select FF520 and press [ENT] or move the ShuttlePoint knob to the right. 6. Press [CLR] or move the ShuttlePoint knob to the left until the Chart page is shown. ***NOTE: AUTOPILOT CONNECTION Care must be taken when connecting the GPS Chart Plotter to an autopilot. Normally Port 3 (Yellow wire) will be used to connect to an Autopilot input, however older autopilots may not be able to read the sentences due to the talker ID that is being used (II Integrated
Summary of the content on the page No. 16
NMEA ACC 2 Cable Pin Wire Color Description Connection Example Additional Comments 1 Black NC 2 Red NC 3 Green NMEA Common Common (ground) for NMEA devices 4 Blue Port 4 Input Connect to Output of NMEA device Default is NMEA0183** 5 Brown Port 4 Output Connect to Input of NMEA device Default is NMEA0183 with GLL, RMB, RMC and XTE sentences 6 Gray Port 5 Input Connect to Output of NMEA device Default is NMEA0183 7 White Port 5 Output Connect to Input of NMEA device Default is NMEA0183 with GLL, R
Summary of the content on the page No. 17
2.4.2.2 Connection of the FF520, AIS receiver, VHF and Autopilot NOTE Port 2 input and output is used by the optional FF520. In the diagram above you will notice Port 2 Input and Output wires are shown in gray and not used. AIS Setup The CP180 or CP180i has to be setup to be able to receive NMEA information from the AIS receiver. 1. Press [Menu], move the ShuttlePoint knob to highlight SETUP MENU and press [ENT]. 2. Move the ShuttlePoint knob to highlight ADVANCED SETUP and press [ENT] or move t
Summary of the content on the page No. 18
NOTE If an AIS receiver is not connected, Port 1 Input can be connected to most DSC VHF’s for position polling. 2.4.3 Connection For CP300/CP300i 2.4.3.1 DC Power Connection 2.4.3.2 Connection a VideoCamera, FF520, AIS receiver, VHF and Autopilot Page 20 GPS Chart Plotters
Summary of the content on the page No. 19
NOTE Port 2 Input and Output is used by the optional FF520. In the diagram above you will notice Port 2 Input and Output wires are shown in gray and not used. Port 4, and 5 Outputs are can be connected to NMEA devices capable of listening to NMEA 0183 sentences. Port 4, and 5 Inputs can be connected to NMEA devices capable of outputting to NMEA 0183 sentences. The Input and Output baud rate for each port are set using the Advanced Setup>In/Out Connections menu. For example if Port 1 is set for A
Summary of the content on the page No. 20
- DSC VHF Radio - Depth Sounder, Speed Log, Wind Instrument, Autopilot etc. - Personal Computer - AIS receiver 2.7 GPS POSITION ON A VHF RADIO STANDARD HORIZON has pioneered Digital Selective Calling (DSC) on VHF radios. Advancements in DSC have made it possible to show the coordinates of a vessel that has transmitted a DSC Distress Call or even Poll the location of another vessel and show the position of that vessel on the display of STANDARD HORIZON VHFs. STANDARD HORIZON has taken this featur
