Summary of the content on the page No. 1
1066 Liquid Analytical Transmitter
Instruction Sheet 1066
LIQ_MAN_ABR_1066-CT-HT-FF-FI July 2013
ESSENTIAL INSTRUCTIONS
Read this page before proceeding!
Emerson designs, manufactures, and tests its Rosemount
Analytical products to meet many national and international
standards. Because these instruments are sophisticated
technical products, you must properly install, use, and main-
tain them to ensure they continue to operate within their
normal specifications. The following instructions must b
Summary of the content on the page No. 2
1066 Instruction Sheet July 2013 LIQ_MAN_ABR_1066-CT-HT-FF-FI QUICK START GUIDE – 1066 Liquid Analytical Transmitter 1. For mechanical installation instructions, see page 8 for panel mounting and page 9 for pipe or wall mounting. 2. Wire the sensor to the main circuit board. See page 10 for wiring instructions. Refer to the sensor instruction sheet for additional details. Make loop power connections. 3. Once connections are secured and verified, apply DC loop power to the transmitter. 4. When
Summary of the content on the page No. 3
Instruction Sheet 1066 LIQ_MAN_ABR_1066-CT-HT-FF-FI July 2013 Specifications GENERAL SPECIFICATIONS Case: Polycarbonate. IP66 (CSA, FM), NEMA 4X (CSA) Dimensions: Overall 155 x 155 x 131mm (6.10 x 6.10 x 5.15 in.). Cutout: 1/2 DIN 139mm x 139mm (5.45 x 5.45 in.) Conduit openings: Six. Accepts PG13.5 or 1/2 in. conduit fittings Display: Monochromatic graphic liquid crystal display. No backlight. 128 x 96 pixel display resolution. Active display area: 58 x 78mm (2.3 x 3.0 in.). All fields of the m
Summary of the content on the page No. 4
1066 Instruction Sheet July 2013 LIQ_MAN_ABR_1066-CT-HT-FF-FI Input: One isolated sensor input. Measurement choices of Vdc (30 Vdc for intrinsically safe operation). The graph pH/ORP, resistivity/conductivity/TDS, % concentration, shows the supply voltage required to maintain 12 Vdc total and free chlorine, monochloramine, dissolved oxy- (upper line) and 30 Vdc (lower line) at the transmitter ter- gen, dissolved ozone, and temperature. For contacting minals when the current is 22 mA. conductivit
Summary of the content on the page No. 5
Instruction Sheet 1066 LIQ_MAN_ABR_1066-CT-HT-FF-FI July 2013 Specifications CONTINUED CONTACTING CONDUCTIVITY Performance Specifications Measurement Range: see table below Input filter: time constant 1 - 999 sec, default 2 sec. Response time: 3 seconds to 95% of final reading using the default input filter Recommended Sensors for Conductivity All Rosemount Analytical ENDURANCE Model 400 series conductivity sensors (Pt 1000 RTD) and Model 410VP 4- electrode sensor. PERFORMANCE SPECIFICATIONS R
Summary of the content on the page No. 6
1066 Instruction Sheet July 2013 LIQ_MAN_ABR_1066-CT-HT-FF-FI Specifications CONTINUED TOROIDAL CONDUCTIVITY Performance Specifications Measurement Range: see table below Input filter: time constant 1 - 999 sec, default 2 sec. Response time: 3 seconds to 95% of final reading Recommended Sensors for Conductivity All Rosemount Analytical submersion/immersion and flow-through toroidal sensors. PERFORMANCE SPECIFICATIONS Recommended Range - Toroidal Conductivity Model 1 mS/cm
Summary of the content on the page No. 7
Instruction Sheet 1066 LIQ_MAN_ABR_1066-CT-HT-FF-FI July 2013 Installation UNPACKING AND INSPECTION Inspect the shipping container. If it is damaged, contact the shipper immediately for instructions. Save the box. If there is no apparent damage, unpack the container. Be sure all items shown on the packing list are present. If items are miss- ing, notify Rosemount Analytical immediately. INSTALLATION General Information 1. Although the transmitter is suitable for outdoor use, installation is dire
Summary of the content on the page No. 8
1066 Instruction Sheet July 2013 LIQ_MAN_ABR_1066-CT-HT-FF-FI FIGURE 3. Panel Mounting Dimensions 8
Summary of the content on the page No. 9
Instruction Sheet 1066 LIQ_MAN_ABR_1066-CT-HT-FF-FI July 2013 FIGURE 4. Pipe and wall mounting dimensions (Mounting bracket PN: 23820-00) 9
Summary of the content on the page No. 10
1066 Instruction Sheet July 2013 LIQ_MAN_ABR_1066-CT-HT-FF-FI FIGURE 5. Contacting and Toroidal Conductivity sensor wiring to 1066 circuit board (1066-C and 1066-T) 10
Summary of the content on the page No. 11
Instruction Sheet 1066 LIQ_MAN_ABR_1066-CT-HT-FF-FI July 2013 FIGURE 6. CSA Installation 11 SCHEMATIC, INSTALLATION MODEL 1066 XMTR, (CSA)
Summary of the content on the page No. 12
1066 Instruction Sheet July 2013 LIQ_MAN_ABR_1066-CT-HT-FF-FI FIGURE 7. CSA Installation 12 SCHEMATIC, INSTALLATION MODEL 1066 XMTR, (CSA)
Summary of the content on the page No. 13
Instruction Sheet 1066 LIQ_MAN_ABR_1066-CT-HT-FF-FI July 2013 FIGURE 8. CSA Installation 13 SCHEMATIC, INSTALLATION MODEL 1066 XMTR, (CSA)
Summary of the content on the page No. 14
1066 Instruction Sheet July 2013 LIQ_MAN_ABR_1066-CT-HT-FF-FI FIGURE 9. CSA Label Information 14 LABEL, INFO, 1066 CSA
Summary of the content on the page No. 15
Instruction Sheet 1066 LIQ_MAN_ABR_1066-CT-HT-FF-FI July 2013 FIGURE 10. ATEX, IECEx Label Information 15 LABEL, INFO, 1066 ATEX 9241717-00
Summary of the content on the page No. 16
1066 Instruction Sheet July 2013 LIQ_MAN_ABR_1066-CT-HT-FF-FI FIGURE 11. FM installation 16 SCHEMATIC, INSTALLATION MODEL 1066 XMTR, (FM)
Summary of the content on the page No. 17
Instruction Sheet 1066 LIQ_MAN_ABR_1066-CT-HT-FF-FI July 2013 FIGURE 12. FM Installation 17 SCHEMATIC, INSTALLATION MODEL 1066 XMTR, (FM)
Summary of the content on the page No. 18
1066 Instruction Sheet July 2013 LIQ_MAN_ABR_1066-CT-HT-FF-FI FIGURE 13. FM installation 18 SCHEMATIC, INSTALLATION MODEL 1066 XMTR, (FM)
Summary of the content on the page No. 19
Instruction Sheet 1066 LIQ_MAN_ABR_1066-CT-HT-FF-FI July 2013 FIGURE 14. FM label information 19 LABEL, INFO, 1066 FM
Summary of the content on the page No. 20
1066 Instruction Sheet July 2013 LIQ_MAN_ABR_1066-CT-HT-FF-FI facebook.com/EmersonRosemountAnalytical AnalyticExpert.com Credit Cards for U.S. Purchases Only. twitter.com/RAIhome youtube.com/user/RosemountAnalytical Emerson Process Management ©2013 Rosemount Analytical, Inc. All rights reserved. 2400 Barranca Parkway The Emerson logo is a trademark and service mark of Emerson Electric Co. Brand name is a mark Irvine, CA 92606 USA of one of the Emerson Process Management family of companies. All
