Summary of the content on the page No. 1
Snapshot
LED Mushroom
OK on Dimmer
Outdoor OK
Sound-Activated
DMX512
Master/Slave
115V/230V Switch
Replaceable Fuse
User-Serviceable
USER MANUAL
5200 NW 108th Avenue, Sunrise, FL 33351 U.S.A.
(800) 762-1084 – (954) 577-4455
FAX (954) 929-5560
www.chauvetlighting.com
Summary of the content on the page No. 2
TABLE OF CONTENTS 1. BEFORE YOU BEGIN............................................................................................................................................................ 3 WHAT IS INCLUDED ...................................................................................................................................................................... 3 UNPACKING INSTRUCTIONS ............................................................................................
Summary of the content on the page No. 3
1. BEFORE YOU BEGIN What is Included Ø 1 x LED Mushroom Ø Warranty Card Ø Power Cord Ø User Manual Unpacking Instructions Immediately upon receiving a fixture, carefully unpack the carton, check the contents to ensure that all parts are present, and have been received in good condition. Notify the shipper immediately and retain packing material for inspection if any parts appear damaged from shipping or the carton itself shows signs of mishandling. Save the carton and all packing materi
Summary of the content on the page No. 4
2. INTRODUCTION Features · 2-channel DMX-512 LED derby effect · Continuous rotation or back and forth motor control · Built-in automated programs via master/slave or DMX · Built-in sound activated programs via master/slave or DMX Additional Features · High-power, 3W (730mA) LEDs · Linkable with Kinta™ X and Double Derby™ X · Additional power output: max 37 units @ 120V and 74 units @ 230V DMX Channel Summary CHANNEL FUNCTION Control/Operating Mode 1 Motor rotation 2 Product Ove
Summary of the content on the page No. 5
Product Overview con’t Hanging/mounting bracket Bracket adjustment knob LED Mushroom User Manual 5 Rev. 4
Summary of the content on the page No. 6
3. SETUP Disconnect the power cord before replacing a fuse and always replace with the same type fuse. Fuse Replacement With a flat-head screwdriver wedge the fuse The fuse is located holder out of its housing. Remove the damaged inside this fuse from its holder and replace with exact compartment. same type fuse. Insert the fuse holder back in Remove using a flat its place and reconnect power. head screwdriver. Data Linking You will need a serial data link to run light shows o
Summary of the content on the page No. 7
Mounting Orientation This product may be mounted in any safe position as long as there is adequate room for ventilation. Rigging Hanging Clamp It is important never to obstruct the fan or vents pathway. Mount the product using, a suitable “C” or “O” type clamp. Adjust the angle of the fixture by loosening both knobs and tilting the fixture. After finding the desired position, retighten both knobs. · When selecting installation location, take into consideration lamp replacement access
Summary of the content on the page No. 8
111111 111111 222222 222222 444444 444444 888888 888888 16 16 16 16 16 16 16 16 16 16 16 16 32 32 32 32 32 32 32 32 32 32 32 32 64 64 64 64 64 64 64 64 64 64 64 64 128 128 128 128 128 128 128 128 128 128 128 128 256 256 256 256 256 256 256 256 256 256 256 256 Setting the Starting Address This DMX mode enables the use of a universal DMX controller device. Choose start addresses so that the channels used do not overlap, and note the start address selected for future reference. Set the start addr
Summary of the content on the page No. 9
DMX Quick Reference Chart DMX Address Quick Reference Chart Dip Switch Position DMX DIP #9 0 0 0 0 0 0 0 0 1 1 1 1 1 1 1 1 SWITCH SET 0=OFF #8 0 0 0 0 1 1 1 1 0 0 0 0 1 1 1 1 1=ON #7 0 0 1 1 0 0 1 1 0 0 1 1 0 0 1 1 X=OFF or ON #6 0 1 0 1 0 1 0 1 0 1 0 1 0 1 0 1 #1 #2 #3 #4 #5 0 0 0 0 0 32 64 96 128 160 192 224 256 288 320 352 384 416 448 480 1 0 0 0 0 1 33 65 97 129 161 193 225 257 289 321 353 385 417 449 481 0 1 0 0 0 2 34 66 98 130 162 194 226 258 290 322 354 386 418 450 482
Summary of the content on the page No. 10
5. APPENDIX General Maintenance To maintain optimum performance and minimize wear fixtures should be cleaned frequently. Usage and environment are contributing factors in determining frequency. As a general rule, fixtures should be cleaned at least twice a month. Dust build up reduces light output performance and can cause overheating. This can lead to reduced lamp life and increased mechanical wear. Be sure to power off fixture before conducting maintenance. Unplug fixture from power. U
Summary of the content on the page No. 11
General Troubleshooting Applies to Foggers Dimmers Symptom Solution(s) Lights & Snow Controllers & Chaser Auto shut off Check fan thermal switch reset ü Beam is very dim or Clean optical system or replace lamp ü not bright Check 220/110v switch for proper setting Breaker/Fuse keeps Check total load placed on device ü blowing Device has no power Check for power on Mains. ü ü ü Check device’s fuse. (internal and/or external) Fixture is not Check DMX Dip switch settings fo
Summary of the content on the page No. 12
Technical Specifications WEIGHT & DIMENSIONS Length ................................................................................................................................................................ 12 in (306 mm) Width ................................................................................................................................................................. 8.1 in (206 mm) Height .............................................................................
