Summary of the content on the page No. 1
EZ-m mini-mixer 10x2
OWNER’S MANUAL
Summary of the content on the page No. 2
Table of Contents Page 1 Introduction / Features / Back Panel diagram 2 Important Safety & Warranty Information 3 Detailed Features of the EZ-m 10x2 – Mic/Line Input Channel 4 Mono Mic/Line Channel - Low Impedance (Low Z) MIC Input - LINE IN - GAIN Control - CLIP LED 5 - Mono Channel EQ Section - Mono Channel PAN and LEVEL 6 Stereo Channel Inputs - BALANCE & LEVEL 7 MASTER Section - POWER LED & Signal Metering 8
Summary of the content on the page No. 3
Introduction Thank you for purchasing a Wharfedale Pro EZ-m mini-mixer. The Wharfedale Pro EZ-m Series mixers are designed for ease of use and quality audio performance. Please read this manual completely to ensure proper understanding of the features and operation of your mixer. FEATURES EZ-m 10x2 - 1 Mono balanced / unbalanced mic / line input channel with 2 Band equalization - 1 variable input GAIN control on channel 1 - CLIP LED on channel 1 - 2 Stereo channels with balanced /
Summary of the content on the page No. 4
Important Safety & Warranty Information 1. Power Supply This EZ-m Series mini-mixer is supplied with an external power supply unit. Use only the power supply provided with your mixer. Use of any other power supply could cause damage to the mixer and other equipment. Connect the power supply to the mixer BEFORE connecting it to the power source outlet. Be sure to allow for free airflow around the mixer, as it may become warm during long periods of operation. The mixer is shipped with the
Summary of the content on the page No. 5
DETAILED FEATURES OF THE EZ-m 10x2 Mono Mic / Line Input Channel 3
Summary of the content on the page No. 6
Low Impedance (Low Z) MIC Input 1 1 The low noise, high headroom “Low Z” MIC input is for use with balanced, low impedance dynamic microphones. NOTE: Condenser microphones will not work on this mixer. LINE IN 2 This ¼” Tip, Ring, Sleeve (TRS) jack is designed to be connected with (-10 to +4dBu) balanced or unbalanced line level sources.
Summary of the content on the page No. 7
EQ Section 5 5 Channel 1 on the EZ-m 10x2 mixer features a two band Equalization (”EQ”) section. Each band is chosen from the prime frequencies for most musical applications, and allows up to 15 decibels of boost (increase) or cut (decrease) of the signal in the tone range for which it controls. The HIGH EQ control is centered at 12kHz and the LOW EQ control is centered at 80Hz. In the center-detent position
Summary of the content on the page No. 8
Stereo Channel Inputs Each of the stereo channels on the EZ-m 10x2 (2/3 and 4/5) feature two line level inputs with ¼” Tip/Ring/Sleeve (TRS) jacks for both balanced and unbalanced left and right input signals. These inputs can accommodate both stereo and mono inputs. When using a mono source,
Summary of the content on the page No. 9
Master Section The master section on the right side of the mixer controls the final gain stage of the mixed signals from the input channels. The MAIN MIX control allows for the adjustment of the overall output level of the EZ-m mixer. 10
Summary of the content on the page No. 10
2TK IN 12 This section consists of two sets of three input jacks. The top rows of jacks are the “2TK IN” input, which includes a 1/8” stereo jack and left and right RCA jacks. These inputs allow for an external stereo signal into the mixer. This 12 signal is controlled by the 2TK IN volume control and the 2TK TO PHONES switch as well as
Summary of the content on the page No. 11
16 16 POWER Switch – On/Off This slide switch turns the unit on and off. Always power down the EZ-m when it is not in use. Be sure to turn off all system amplifiers or powered speakers before turning off the mixer. 17 AC Power Cable Connector The included power adaptor connects here. Use only the power adaptor supplied with the mixer. 17 CONNECTION WIRING DETAILS MIC Inputs (Microphone) The microphone (MIC) jack is a female XLR connector wired balanced with: Pin 1 = ground,
Summary of the content on the page No. 12
SPECIFICATIONS EZ-m mini-mixer 10X2 Specifications Maximum Output Level +22dBu over 130mw (headphone) @ 32 ohms (1%T.H.D. @ 1kHz) THD+N% <0.01% @ +15dBu Frequency Response 20Hz-20kHz +0/-1dB -127dB Mic Pre Equivalent Input Noise Hum and Noise '-90dBu Residual Noise Mic In: '+10dBu
Summary of the content on the page No. 13
BLOCK DIAGRAM 11
Summary of the content on the page No. 14
Wharfedale International LTD. IAG HOUSE Sovereign Court, Ermine Business Park, Huntingdon, Cambs, PE29 6XU, England www.wharfedalepro.com IAG Professional reserves the right to alter or improve specifications without notice. All rights reserved © 2007 Wharfedale Pro Wharfedale Pro is a member of the International Audio Group
