Summary of the content on the page No. 1
pecifications
S
INTERNATIONAL
®
Blending Station On-Counter:
FOODSER VICE
Height of unit closed: 54.56 cm • Shipping weight: 9.534 kg
Dimensions 54.56 cm H x 23.45 cm W x 25.86 cm D
Owner’s Manual
Read And Save These Instructions
Blending Station In-Counter:
Height of unit above counter: 44.45 cm closed
Depth of unit below counter: 14.4 cm • Shipping Weight: 8.172 kg
Dimensions: 45.03 cm H x 23.45 cm W x 25.86 cm D
NOTE: For In-Counter Installation refer to pages 8-10.
Power Requirements:
Volt
Summary of the content on the page No. 2
13. Always operate with the lid in place. IMPORTANT SAFEGUARDS 14. WARNING: When processing hot liquids: • The 2-part latching lid must be securely in place. This allows steam 1. Read all instructions. to escape naturally, and will prevent the lid from coming off when 2. To protect against risk of electrical shock, do not put motor base in the machine is turned on. water or other liquid. • Use caution with hot liquids. Spraying from under the lid plug can 3. Close adult supervision is necessary
Summary of the content on the page No. 3
Summary of the content on the page No. 4
Summary of the content on the page No. 5
Electrical requirements: n-Counter Installation I • Volts: 220/240 VAC • 50 or 60 Hz. • 1073-1178 Watts • Volts: 100 VAC, 60 Hz., 900 Watts (Japan) Blending Station dimensions: Preparing the counter area: • 44.45 cm high with lid closed • Before cutting holes, make sure that there is adequate clearance under • 54.7 cm high with lid open the counter for the motor. The motor will extend about 14.4 cm below the • Case depth: 31.75 cm with handle counter but it is best to allow at least 25.4 cm from
Summary of the content on the page No. 6
n-Counter Gasket I lending Tips B 1. If your recipe freezes up, try reducing the amount of ice. Compared Gasket Installation Instructions: to other blenders, you do not need as much ice to make an equally 1. Follow the instructions on page 8 on preparing the counter area for TM ® frozen drink in a Touch and Go Blending Station. TM ® the installation of your In-Counter Touch and Go Blending Station. 2. Place liquids and soft foods in your container first. Hard items and ice Also, use the Temp
Summary of the content on the page No. 7
id Assembly L Tamper Two-part Lid One Piece Lid (optional) 1.5 Liter Polycarbonate container 2 Liter Polycarbonate container The two part lid is easy to clean and easy to put on, The one piece lid is easy to clean and easy to put take off and seal. on and take off. Figure C • To remove fully latched lid, squeeze tabs (Note: Brand new lids are a little stiff. This is temporary.) together on both sides of the container, pull • There is no latch on this lid. upward and off. • Add ingredients thro
Summary of the content on the page No. 8
nstructions I 4. Select desired programmed setting by pressing any of the Pre-Set Buttons 1 through 6. The machine will begin immediately to cycle ® How to operate your Blending Station using the through the selected program, and turn off when the program is complete. six Pre-Set Programmed buttons. Each button has a different pre-selected combination of speed and length The following is the basic factory settings of the six PRE-SET buttons for blending. (your machines PRE-SET buttons may be
Summary of the content on the page No. 9
Summary of the content on the page No. 10
Summary of the content on the page No. 11
are and Cleaning C Container Care Note 1. To clean: Fill pitcher 1/4 full with warm (43˚C) water and add a couple Do not let mixtures, liquids and food products dry within the container. Rinse drops of dish soap.* Return container to motor base and firmly position throughout use. Drying product may lock around the blade and weaken/tear the two part lid. Run machine for 30 seconds. Empty container. Repeat the bearings seal when restarted. Do not place containers in the freezer. this step. Extrem
Summary of the content on the page No. 12
7. Problem: Solution #1: • Machine is running irregular Turn the machine off and on again to reset roubleshooting T • Display panel reads garbage the programming • “NO PROGRAM” is displayed when a Solution #2 button is pushed Reset the machine to its original factory • Button pressed starts the wrong settings. (Follow the instructions on page 7) program Solution #3: Top nine problems you can fix on your own: • Machine starts by itself Try plugging the machine into a new outlet. 1. Problem: Solu
Summary of the content on the page No. 13
pecifications S ® Blending Station On-Counter: Height of unit closed: 54.56 cm • Shipping weight: 9.534 kg Dimensions 54.56 cm H x 23.45 cm W x 25.86 cm D Blending Station In-Counter: Height of unit above counter: 44.45 cm closed Depth of unit below counter: 14.4 cm • Shipping Weight: 8.172 kg Dimensions: 45.03 cm H x 23.45 cm W x 25.86 cm D NOTE: For In-Counter Installation refer to pages 8-10. Power Requirements: Volts: 220/240 VAC, 50 or 60 Hz, 1073-1178 Watts 100 VAC, 60 Hz, 900 Watts (Jap
