Summary of the content on the page No. 1
Transport GS10 / / / B2094T15
Revision 1.00
Copyright © TYAN Computer Corporation, 2003. All rights reserved. No part of this manual may
be reproduced or translated without prior written consent from TYAN Computer Corp.
All registered and unregistered trademarks and company names contained in this manual are
property of their respective owners including, but not limited to the following:
TYAN, T ransport GS10 B2094T15 are trademarks of TYAN Computer Corporation.
Intel,
Summary of the content on the page No. 2
0 Table of Contents Safety Precautions........................................................................................................4 1 Introduction .......................................................................................................................5 1.1 Before You Begin ........................................................................................................5 Unpacking..............................................................................
Summary of the content on the page No. 3
4 Configuring the System.................................................................................................29 4.1 BIOS Setup Program..................................................................................................29 Starting BIOS Setup ...................................................................................................29 Main Menu.................................................................................................................
Summary of the content on the page No. 4
Safety Precautions l Use the type of pow er indicated on the marking label. l Ensure electrical circuits are not overloaded; consider the nameplate ratings of all the connected equipment and ensure you have over current protection. l Do not disable the power cord ground feature. This equipment was designed to connect to a grounded (earthed) power outlet. The grounding plug is an important safety feature. l Ensure that the power outlet is located or installed near the equipment and is easil
Summary of the content on the page No. 5
1 Introduction This chapter introduces the features and functions of the product. 1.1 Before You Begin This manual provides hardware-related information of the system for administrators who use it to develop and host web sites. The administrators should be familiar with operating systems and web browsers. Depending on the model purchased, your system may come with pre-installed software. For software information, refer to the documentation accompanying the software. Unpacking After unpa
Summary of the content on the page No. 6
Inspect all the items. If any item is damaged or missing, notify your dealer immediately. Keep the shipping carton and packing materials in case you need to ship or store the computer in the future. 1.2 Product Description Congratulations on purchasing the system. It is a server appliance providing a dedicated web-hosting platform, pre-packaged in an industry standard 1U rackmount enclosure. With appropriate application software, the system offers a full suite of Internet services includin
Summary of the content on the page No. 7
1.3 Specifications NOTE: Specifications are subject to change without notice. Processor Storage Interface • Single socket 478 • Integrated two master IDE RAID controller (Promise PDC20276) • Intel Pentium 4 processor up to 3.06 GHz • Supports 400/533 MHz FSB • Supports RAID level 0, 1 Storage Capacity Chipset • Up to two IDE drives • Intel 845E MCH • MCH + ICH-4 Integrated Hardware Monitoring • NS PC87366 Super I/O chip • Integrated in Super I/O • CPU temperature and voltage m
Summary of the content on the page No. 8
1.4 System View Front View Ref Component Description Power Button Turns the power on and off (soft-off). Power Indicator Glows green when the power is on. LAN1 Indicator Indicates an active network connection on LAN1 (external connection). LAN2 Indicator Indicates an active network connection on LAN2 (internal connection). Hard Disk Drive Indicates activity on the hard disk drive. Indicator LCD Screen Displays messages and values entered. Control Buttons Allow you t
Summary of the content on the page No. 9
Rear View Ref Component Description Ventilation Openings Maintain proper operating temperature. Do not cover or block the openings. Power Connector Connects the power cord. Power Switch Turns the main power of the system on and off. LAN1 Connector Connects the LAN cable for internal network connection. LAN2 Connector Connects the LAN cable for external network connection. VGA Port Connects an external CRT monitor. Serial Port Connects a serial device. USB Ports E
Summary of the content on the page No. 10
Summary of the content on the page No. 11
2 Cabinet Installation This chapter, which is divided into two sections, provides instructions on the hardware installation of the system. System Assembly section illustrates how to assemble each component of the system. Rack Mounting section describes the procedures for mounting the system into the rack. You can use the system assembly flowchart and the chart next to determine the proper sequence for removing or installing components to the server. Cabinet Cover CPU and Heatsink Sys
Summary of the content on the page No. 12
System Assembly Flowchart The following flowchart shows the basic procedures of system assembly: NOTE: Please wear anti -static gloves when handling electrical components and exercise caution during the installation process. For more information, contact your local dealer or an experienced technician. START CONNECT HARD DISK DRIVE CABLE AND POWER CORD REMOVE CABINET COVER AND AIR DUCT INSTALL RISER CARD INSTALL CPU AND HEATSINK CHECK IF ALL PARTS ARE PROPERLY CONNECTED REPLA
Summary of the content on the page No. 13
2.1 System Assembly When installing a device, be sure to read the instructions accompanying the device together with the relevant section in this chapter. Opening the Cover CAUTION: l Static electricity can destroy electronic devices. W henever you handle an option outside of its protective packaging, first discharge any static electricity from your body by touching a protective grounding device or unpainted metal on the rear panel of the system before unplugging the power cord. l Befor
Summary of the content on the page No. 14
3. Locate the CPU socket and lift the socket arm up to the vertical position. Align the new CPU so its Pin 1 corner (beveled corner) is at the Pin 1 corner of the socket. 4. Insert the CPU pins into the socket. Press the arm downward to the horizontal position. You will feel some resistance while doing so. This is normal as the pressure starts to secure the CPU in place. 14 http://www.TYAN.com
Summary of the content on the page No. 15
5. Align the four points of the heatsink socket and secure with four screws following a diagonal sequence. 6. Place the air duct back into place and secure with three screws. 7. Replace the cabinet cover. Installing System Memory Your system has two 184-pin DIMM (Dual In-line Memory Module) sockets to support a maximum of 2 GB. You must follow these requirements for the DIMM to be used with the system: l Unbuffered DDR-SDRAM (Double Data Rate Synchronous DRAM) with ECC l PC1600/PC2100
Summary of the content on the page No. 16
3. To install the DIMM, make sure the retaining clips are in the unlocked position, then align the DIMM’s notched end with the socket’s corresponding end and firmly insert the DIMM into the socket. Finally push the retaining clips inwards to lock the DIMM in place. 4. Replace the cabinet cover. Installing a Hard Disk Drive NOTE: Make sure that the jumper setting of the hard disk drive is set to “Master.” (See the hard disk drive’s documentation for information.) 1. Remove the cabine
Summary of the content on the page No. 17
3. Fit a hard disk drive to the bracket and secure with four screws. 4. Fit the bracket with the hard disk drive back into place and secure with one screw. Connect the data cable and power cord. 5. Replace the cabinet cover. 6. You can create or rebuild RAID for the hard disk drive (see chapter 7 for information). Installing a Riser Card Your system has one PCI slot located on the system board. You need to install a riser card to be able to install an expansion card for additional o
Summary of the content on the page No. 18
2. Locate the PCI slot. 3. Firmly press the riser card’s edge connector into the PCI slot. 4. Replace the cabinet cover. 2.2 Rack Mounting The slide rackmount kit provides a sliding rackmount solution for the product. Slides enable optimal serviceability of the server from the front of the rack, including accessibility to the rear of the server for cabling and the capability for top cover removal. It is compatible with most 19” EIA standard 4 post racks with non-threaded holes. After u
Summary of the content on the page No. 19
2. Detach the inner slide from the outer slide by pressing on the release latch and pulling apart the inner slide from the outer slide . Do the same for the other slide. 3. Align the inner slide’s first round screwhole with the screwhole on the system chassis beside the mounting ears and attach the screw together with next screwhole. Do the same for the other side . NOTE: For the correct orientation on mounting the inner slides to the cabinet, refer to the picture above. 4. Attac
Summary of the content on the page No. 20
Cabinet into the Rack Slide system cabinet with the inner s lides previously installed into the inner rails of the outer slides attached to the rack and press on the release latch until the front panel is aligned with the front edge of the rack. Locking Tab To prevent the system chassis from sliding on its rails, secure the system cabinet to the rack with a screw on each of the mounting ears (optional – refer to the figure above). 20 http://www.TYAN.com
