Summary of the content on the page No. 1
BiPAC 7404V Series
VoIP/(802.11g) ADSL2+
(VPN) Firewall Router
User’s Manual
Version Release 5.07
Last Revision Date: 08-15-2006
Summary of the content on the page No. 2
Table of Contents Table of Contents CHAPTER 1: INTRODUCTION ............................................................................................................. 4 INTRODUCTION TO YOUR ROUTER................................................................................................. 4 FEATURES .............................................................................................................................................. 4 CHAPTER 2: INSTALLING THE ROUTER .....
Summary of the content on the page No. 3
WAN - Wide Area Network.................................................................................................................. 41 ISP .................................................................................................................................................. 41 DNS ................................................................................................................................................ 51 ADSL..............................................
Summary of the content on the page No. 4
PROBLEMS WITH THE LAN INTERFACE ..................................................................................... 153 APPENDIX A: PRODUCT SUPPORT AND CONTACT INFORMATION.................................... 154 Table of Contents iii
Summary of the content on the page No. 5
VoIP/(802.11g) ADSL2+ (VPN) Firewall Router Chapter 1: Introduction Introduction to your Router Welcome to the VoIP/(802.11g) ADSL2+ (VPN) Firewall Router. The router is an “all-in-one” VoIP ADSL router, combining an ADSL modem, ADSL router, Ethernet network switch and 2 ports for Voice over IP functionalities, providing everything you need to get the machines on your network connected to the Internet over your ADSL broadband connection. With features such as an ADSL Quick-Start w
Summary of the content on the page No. 6
VoIP/(802.11g) ADSL2+ (VPN) Firewall Router directly for auto detection. Multi-Protocol to Establish a Connection It supports PPPoA (RFC 2364 - PPP over ATM Adaptation Layer 5), RFC 1483 encapsulation over ATM (bridged or routed), PPP over Ethernet (RFC 2516), and IPoA (RFC1577) to establish a connection with the ISP. The product also supports VC-based and LLC-based multiplexing. Quick Installation Wizard It supports a WEB GUI page to install this device quickly. With this wi
Summary of the content on the page No. 7
VoIP/(802.11g) ADSL2+ (VPN) Firewall Router Rich Packet Filtering Not only filters the packet based on IP address, but also based on Port numbers. It will filter packets from and to the Internet, and also provides a higher level of security control. Dynamic Host Configuration Protocol (DHCP) Client and Server In the WAN site, the DHCP client can get an IP address from the Internet Service Provider (ISP) automatically. In the LAN site, the DHCP server can allocate a range of c
Summary of the content on the page No. 8
VoIP/(802.11g) ADSL2+ (VPN) Firewall Router Chapter 2: Installing the Router Important note for using this router Do not use this router in high humidity or high temperatures. Do not use the same power source for this router as other equipment. Do not open or repair the case yourself. If this router is too hot, turn off the power immediately and have it repaired at a qualified Warning service center. Avoid using this product and all accessories outdoors.
Summary of the content on the page No. 9
VoIP/(802.11g) ADSL2+ (VPN) Firewall Router The Front LEDs LED Meaning 1 PWR Lit when power is ON. 2 SYS Lit when the system is ready. LAN Port Lit when connected to an Ethernet device. 3 – 6 1X — 4X Green for 100Mbps; Orange for 10Mbps. (RJ-45 connector) Blinking when data is Transmitted / Received. WLAN Lit green when the wireless connection is established. 7 (Wireless Router only) Flashes when sending/receiving data. Phone 8 – 9 1X — 2X Lit green when the phon
Summary of the content on the page No. 10
VoIP/(802.11g) ADSL2+ (VPN) Firewall Router The Rear Ports 6 5 3 1 4 7 2 8 The Ethernet Port # 4 can be used as a console port. You need a special console tool which already includes in the package to connect with LAN port 4 and PC’s RS-232 port (9-pin serial port). Port Meaning Power Switch 1 Power ON/OFF switch PWR 2 Connect the supplied power adapter to this jack. To be sure the device is being turned on press RESET button for: 1-3 seconds: quick
Summary of the content on the page No. 11
VoIP/(802.11g) ADSL2+ (VPN) Firewall Router Connect the supplied RJ-11 (“telephone”) cable to this port ADSL 7 when connecting to the ADSL/telephone network. Antenna Connect the detachable antenna to this port. 8 (Wireless Router only) Cabling One of the most common causes of problems is bad cabling or ADSL line(s). Make sure that all connected devices are turned on. On the front of the product is a bank of LEDs. Verify that the LAN Link and ADSL line LEDs are lit. If they
Summary of the content on the page No. 12
VoIP/(802.11g) ADSL2+ (VPN) Firewall Router Chapter 3: Basic Installation The router can be configured with your web browser. A web browser is included as a standard application in the following operating systems: Linux, Mac OS, Windows 98/NT/2000/XP/Me, etc. The product provides an easy and user-friendly interface for configuration. Please check your PC’s network components. The TCP/IP protocol stack and Ethernet network adapter must be installed. If not, please refer to your W
Summary of the content on the page No. 13
VoIP/(802.11g) ADSL2+ (VPN) Firewall Router Connecting Your Router 1. Connect this router to a LAN (Local Area Network) and the ADSL/telephone (ADSL) network. 2. Power on the device. 3. Make sure the PWR and SYS LEDs are lit steadily and that the LAN LED is lit. 4. Connect an RJ11 cable to VoIP port when connecting to an analog phone set. 5. Connect RJ-11 cable to LINE Port when connecting to the telephone wall jack. Switchin g/HUB ADSL Phone ADSL Splitte Line Ana
Summary of the content on the page No. 14
VoIP/(802.11g) ADSL2+ (VPN) Firewall Router Configuring PCs in Windows in Window XP 1. Go to Start / Control Panel (in Classic View). In the Control Panel, double-click Network Connections. 2. Double-click Local Area Connection. (See Figure 3.1) Figure 3.1: LAN Area Connection 3. In the LAN Area Connection Status window, click Properties. (See Figure 3.2) Figure 3.2: LAN Connection Status 4. Select Internet Protocol (TCP/IP) and clic
Summary of the content on the page No. 15
VoIP/(802.11g) ADSL2+ (VPN) Firewall Router Configuring PCs in Windows 2000 1. Go to Start / Settings / Control Panel. In the Control Panel, double-click Network and Dial-up Connections. 2. Double-click Local Area (“LAN”) Connection. (See Figure 3.5) Figure 3.5: LAN Area Connection 3. In the LAN Area Connection Status window, click Properties. (See Figure 3.6) Figure 3.6: LAN Connection Status 4. Select Internet Protocol (TCP/IP) and
Summary of the content on the page No. 16
VoIP/(802.11g) ADSL2+ (VPN) Firewall Router Configuring PC in Windows 95/98/ME 1. Go to Start / Settings / Control Panel. In the Control Panel, double-click Network and choose the Configuration tab. 2. Select TCP / IP -> NE2000 Compatible, or the name of any Network Interface Card (NIC) in your PC. (See Figure 3.9) 3. Click Properties. Figure 3.9: TCP / IP 4. Select the IP Address tab. In this page, click the Obtain an IP address automatically radio
Summary of the content on the page No. 17
VoIP/(802.11g) ADSL2+ (VPN) Firewall Router Configuring PC in Windows NT4.0 1. Go to Start / Settings / Control Panel. In the Control Panel, double-click Network and choose the Protocols tab. 2. Select TCP/IP Protocol and click Properties. (See Figure 3.12) Figure 3.12: TCP / IP 3. Select the Obtain an IP address from a DHCP server radio button and click OK. (See Figure 3.13) Figure 3.13: IP Address 16 Chapter 3: Basic Installation
Summary of the content on the page No. 18
VoIP/(802.11g) ADSL2+ (VPN) Firewall Router Factory Default Settings Before configuring your, you need to know the following default settings. Web Interface (Username and Password) Username: admin Password: admin The default username and password are “admin” and “admin” respectively. If you ever forget the username/password to login to the router, you may press the RESET button up to 6 seconds to restore the factory default settings. Caution: After pressing the RESET bu
Summary of the content on the page No. 19
VoIP/(802.11g) ADSL2+ (VPN) Firewall Router Information from your ISP Before configuring this device, you have to check with your ISP (Internet Service Provider) to find out what kind of service is provided such as DHCP (Obtain an IP Address Automatically, Static IP (Fixed IP Address) and PPPoE. Gather the information as illustrated in the following table and keep it for reference. VPI/VCI, VC / LLC-based multiplexing, Username, Password, Service Name, and Domain Name System (DNS
Summary of the content on the page No. 20
VoIP/(802.11g) ADSL2+ (VPN) Firewall Router Configuring with your Web Browser Open your web browser, enter the IP address of your router, which by default is 192.168.1.254, and click “Go”, a user name and password window prompt will appear. The default username and password are “admin” and “admin” respectively. (See Figure 3.14) Figure 3.14: User name & Password Prompt Widonw Congratulation! You are now successfully logon to the VoIP/(802.11g) ADSL Router! 19 Chapt
