Summary of the content on the page No. 1
®
Hotwire 6212 ADSL Router
User’s Guide
Document Number 6212-A2-GB20-00
May 2004
Summary of the content on the page No. 2
Copyright © 2004 Paradyne Corporation. All rights reserved. Printed in U.S.A. Notice This publication is protected by federal copyright law. No part of this publication may be copied or distributed, transmitted, transcribed, stored in a retrieval system, or translated into any human or computer language in any form or by any means, electronic, mechanical, magnetic, manual or otherwise, or disclosed to third parties without the express written permission of Paradyne Corporation, 8545 126
Summary of the content on the page No. 3
Important Safety Instructions 1. Read and follow all warning notices and instructions marked on the product or included in the manual. 2. Slots and openings in the cabinet are provided for ventilation. To ensure reliable operation of the product and to protect it from overheating, these slots and openings must not be blocked or covered. 3. Do not allow anything to rest on the power cord and do not locate the product where persons will walk on the power cord. 4. Do not attempt to service
Summary of the content on the page No. 4
CE Marking When the product is marked with the CE mark on the equipment label, a supporting Declaration of Conformity may be downloaded from the Paradyne World Wide Web site at www.paradyne.com. Select Support -> Technical Manuals -> Declarations of Conformity. FCC Part 15 Declaration An FCC Declaration of Conformity may be downloaded from the Paradyne World Wide Web site at www.paradyne.com. Select Support -> Technical Manuals -> Declarations of Conformity. This device complies with
Summary of the content on the page No. 5
Notice to Users of the United States Telephone Network The following notice applies to versions of the modem that have been FCC Part 68 approved. This equipment complies with Part 68 of the FCC rules and the requirements adopted by the Administrative Council for Terminal Attachment (ACTA). On the bottom side of this equipment is a label that contains, among other information, a product identifier in the format US:AAAEQ##TXXXX. If requested, this number must be provided to the Telephone Co
Summary of the content on the page No. 6
Notice to Users of the Canadian Telephone Network NOTICE: This equipment meets the applicable Industry Canada Terminal Equipment Technical Specifications. This is confirmed by the registration number. The abbreviation IC before the registration number signifies that registration was performed based on a Declaration of Conformity indicating that Industry Canada technical specifications were met. It does not imply that Industry Canada approved the equipment. NOTICE: The Ringer Equivalence
Summary of the content on the page No. 7
Table of Contents Chapter 1 Introduction ......................................................9 1.1 Product Overview ................................................................9 1.2 Features .......................................................................... 10 1.3 Application ....................................................................... 11 1.4 Front Panel LED Indicators.................................................. 12 Chapter 2 Hardware Installation...........
Summary of the content on the page No. 8
6.2 System Statistics .............................................................. 72 6.3 ATM statistics ................................................................... 75 Chapter 7 Diagnostics ......................................................77 7.1 OAM Loopback.................................................................. 77 7.2 Ping ................................................................................ 78 Chapter 8 Firmware Upgrade ..............................
Summary of the content on the page No. 9
Chapter 1 Introduction ® This chapter introduces the Hotwire 6212 ADSL Router. It includes a product overview, a description of the product’s features and applications, and an explanation of the functions of the Front panel LED indictors. 1.1 Product Overview The Hotwire 6212 ADSL Router is an ADSL router integrated with a USB and an Ethernet Interface. The USB and four Ethernet ports can be used simultaneously, allowing a total of five PCs to be connected to the Hotwire 6212 and access
Summary of the content on the page No. 10
1.2 Features The ADSL Router is a compact and high performance standalone unit that provides: Four Ethernet ports and one USB port for LAN connection One console port for local management Stateful packet inspection and filtering Denial of Service protection IGMP Proxy G.dmt, G.lite, and T1.413 Remote configuration and upgrade Auto-negotiation rate adaptation AAL5 for ATM over ADSL UBR, CBR, VBR-real-time, VBR-non-realtime ATM services VC-based and LLC multiplexing Up
Summary of the content on the page No. 11
1.3 Application The figure below shows a possible application of the router. 6212-A2-GB20-00 May 20 04 11
Summary of the content on the page No. 12
1.4 Front Panel LED Indicators LED Indicator Color Mode Function Power Green On Power is supplied Off Power is not supplied LAN 1x – 4x Green On An Ethernet link is established Off An Ethernet link is not established Flash Activity over the Ethernet link USB Green On A USB link is connected Off A USB link is not connected ADSL Link Green Flash The ADSL Link is training On The ADSL Link is established Off The ADSL link is not connected ADSL TX/RX Green Flash Packets transmitt
Summary of the content on the page No. 13
Chapter 2 Hardware Installation 2.1 Installation The Hardware installation procedure is explained below. Caution: Always disconnect all telephone lines from the telephone wall outlet before servicing or disassembling this device. 1. Verify that the On/Off switch on the rear panel is in the Off position. 2. Connect the power adapter to the Power jack of the device, and then plug the power adapter into the wall outlet. 3. Connect the USB port to a PC with a standard USB cable. 4. Conn
Summary of the content on the page No. 14
2.2 Installing the USB Driver Before you connect your router’s USB cable to your PC, you must load the ADSL USB drivers and configure the device via the LAN port using Web management. There are two ways to install the USB driver: • Auto-installation: Install the driver by inserting the CD in the CD drive of your PC and letting the installation automatically start. • Manual installation: Install the driver with the Windows Hardware Wizard. When using the USB port the LAN port must be va
Summary of the content on the page No. 15
2.2.1 Auto Installation STEP 1: Insert the CD-ROM disc for the ADSL USB router. STEP 2: The CD-ROM will auto-play and you will see the following screen. Click on Next to continue. (If the screen doesn’t appear, browse the CD-ROM and double-click on INSTALL.EXE.) 6212-A2-GB20-00 May 20 04 15
Summary of the content on the page No. 16
STEP 3: When prompted by the message shown below, connect your router to a USB port of your PC. Then click on OK. STEP 4: A completion message appears when the installation is complete. Click on Finish. 16 May 2004 6212-A2-GB20-00
Summary of the content on the page No. 17
2.2.2 Manual Installation To connect the router to a PC using the USB interface, you need to use a standard USB cable and install the USB interface software. Follow the steps below. STEP 1: Connect the USB router to the PC by plugging the flat connector of a standard USB cable into a USB port on your PC, and plugging the square connector into the router. The Found New Hardware screen appears: STEP 2: When the screen appears as below, click on the Next button. 6212-A2-GB20-
Summary of the content on the page No. 18
STEP 3: When the screen appears as below, select Search for a suitable driver and click the Next button. 18 May 2004 6212-A2-GB20-00
Summary of the content on the page No. 19
STEP 4: Select Specify a location and click on the Next button. If you are installing the software from a disk, insert the disk. : Select the location of the file using the Browse button. STEP 5 6212-A2-GB20-00 May 20 04 19
Summary of the content on the page No. 20
STEP 6: Enter the correct file for your operating system, select the ADIRNDIS.INF file, and click on the Open button. STEP 7: When the screen below appears, click on the OK button. 20 May 2004 6212-A2-GB20-00
