Summary of the content on the page No. 1
VDSL2 Router
VC-200M / VC-200S
User’s Manual
Summary of the content on the page No. 2
Copyright Copyright © 2008 by PLANET Technology Corp. All rights reserved. No part of this publication may be reproduced, transmitted, transcribed, stored in a retrieval system, or translated into any language or computer language, in any form or by any means, electronic, mechanical, magnetic, optical, chemical, manual or otherwise, without the prior written permission of PLANET. PLANET makes no representations or warranties, either expressed or implied, with respect to the contents her
Summary of the content on the page No. 3
FCC Caution: To assure continued compliance (example-use only shielded interface cables when connecting to computer or peripheral devices). Any changes or modifications not expressly approved by the party responsible for compliance could void the user’s authority to operate the equipment. This device complies with Part 15 of the FCC Rules. Operation is subject to the Following two conditions: (1) This device may not cause harmful interference, and (2) this Device must accept any interfer
Summary of the content on the page No. 4
Revision User’s Manual for VDSL2 Router Model: VC-200M / VC-200S Rev: 2.0 (March 2008) Part No. EM-VC200 4
Summary of the content on the page No. 5
Table of Contents CHAPTER 1 INTRODUCTION................................................................................7 1.1 Feature...............................................................................................................7 1.2 Package Contents ..............................................................................................8 1.3 Physical Details.................................................................................................8 CHAPTER 2 HAR
Summary of the content on the page No. 6
3.5.5.1 LAN Setting.................................................................................37 3.5.5.2 DHCP Client List.........................................................................38 3.5.6 NAT.......................................................................................................38 3.5.6.1 Virtual Server...............................................................................39 3.5.6.2 Port Mapping .....................................................
Summary of the content on the page No. 7
Chapter 1 Introduction The PLANET VDSL2 Router, VC-200M / VC-200S is based on two core networking technologies: Ethernet and VDSL2 (Very High Speed Digital Subscriber Line 2). This technology offers the absolute fastest possible data transmission speeds over existing copper telephone lines without the need for rewiring. The ideal situation, the date rate of VDSL2 can up to 40Mbps upstream and 100Mbps downstream. The VC-200M / VC-200S supports ITU-T G993.2, and provide selectable operatin
Summary of the content on the page No. 8
Selectable VDSL2 transmission modes. User can choose transmission modes (8a,8b,12a,12b,and 17a) through management interface on VC-200M / VC-200S User Friendly Interface. VC-200M / VC-200S can be managed and controlled through Web UI. LAN Features 4-Port Switch. The VC-200M / VC-200S incorporates a 4-port 10/100BaseT switching hub, making it easy to create or extend your LAN. DHCP Server Support. Dynamic Host Configuration Protocol provides a dynamic IP address to PCs and o
Summary of the content on the page No. 9
Front Panel LED definition LED State Description When the router is powered on, and in ready ON state. PWR OFF When the router is powered off. Router is trying to establish a connection Flashing between VC-200M and VC-200S, or telecom’s network. LNK DSL Successfully connected between VC-200M ON and VC-200S, or router and telecom's network, and in ready state. ACT Flashing Data is being transmitted or received. LNK/ACT Data is being transmitted or received via the Flashing/ON LAN
Summary of the content on the page No. 10
The RJ-11 connector allows voice communication between the router PHONE and phone through a twisted-pair phone wire. The RJ-11 connector allows data communication between the router and VDSL2 the VDSL2 network through a twisted-pair phone wire Chapter 2 Hardware Installation This chapter offers information about installing your router. If you are not familiar with the hardware or software parameters presented here, please consult your service provider for the values needed. 2.1 Sys
Summary of the content on the page No. 11
VC-200S. II. Uses the supplied RJ-11cable connects to VC-200M or VC-200S with your phone company. Step 2. Connect a Workstation to the Router's LAN port Uses the supplied RJ-45 cable connects to PC with the Switching Hub port of VC-200M / VC-200S. Both 10Base-T and 100Base-TX connections can be used simultaneously. If required, using a standard RJ-45 cable connect to any LAN port of VC-200M / VC-200S with a normal Hub. Any LAN port of VC-200M / VC-200S will automatically function as
Summary of the content on the page No. 12
3. In the Local Area Connection Status window, click Properties. 4. Select Internet Protocol (TCP/IP) and click Properties. 12
Summary of the content on the page No. 13
5. Select the Obtain an IP address automatically and the Obtain DNS server address automatically radio buttons. 6. Click OK to finish the configuration. Configuring PC in Windows 2000 1. Go to Start / Settings / Control Panel. In the Control Panel, double-click on Network and Dial-up Connections. 2. Double-click Local Area Connection. 3. In the Local Area Connection Status window click Properties.
Summary of the content on the page No. 14
4. Select Internet Protocol (TCP/IP) and click Properties. 5. Select the Obtain an IP address automatically and the Obtain DNS server address automatically radio buttons. 6. Click OK to finish the configuration. Configuring PC in Windows 98/Me 1. Go to Start / Settings / Control Panel. In the Control Panel, double-click on Network and choose the Configuration tab. 2. Select TCP/IP -> NE2000 Compatible, or the name of your Network Interface Card (NIC) in your PC.
Summary of the content on the page No. 15
3. Select the Obtain an IP address automatically radio button. 4. Then select the DNS Configuration tab. 5. Select the Disable DNS radio button and click OK to finish the configuration. Configuring PC in Windows NT4.0 1. Go to Start / Settings / Control Panel. In the Control Panel, double-click on Network and choose the Protocols tab. 2. Select TCP/IP Protocol and click Properties.
Summary of the content on the page No. 16
3. Select the Obtain an IP address from a DHCP server radio button and click OK. Note: By factory default: DHCP is disabled, Device Mode is Bridge Mode, VC-200M’s default LAN IP address is 192.168.1.100, and VC-200S is 192.168.1.200. So please set fix IP address in TCP/IP properties of your network card (show as below), then you can start your Web Browser to login VC-200M or VC-200S (please see Chapter 3.3).
Summary of the content on the page No. 17
Chapter 3 Configuration 3.1 Determine your connection settings Before you configure the router, you need to know the connection information supplied by your VDSL2 service provider. 3.2 Connecting the VDSL2 Router to your network Unlike a simple hub or switch, the setup of the VDSL2 Router consists of more than simply plugging everything together. Because the Router acts as a DHCP server, you will have to set some values within the Router, and also configure your networked PCs to acc
Summary of the content on the page No. 18
3.3 Configuring with Web Browser It is advisable to change the administrator password to safeguard the security of your network. 1. To configure the router, open your browser, type http://192.168.1.100 for VC-200M and http://192.168.1.200 for VC-200S in the browsers address box. Save this address in your Favorites for future reference. At login prompt will appear, and default password is “admin”, then click 'LOGIN'. 3.4 Quick Installation There are two device modes: Bridge Mode
Summary of the content on the page No. 19
Step1- Click “Bridge Mode” in VC-200M and VC-200S, and then press “APPLY” to submit setting. Step2- Select profile in VC-200M and VC-200S, we suggest select same profile in VC-200M and VC-200S, otherwise the connection won’t synchronously. 19
Summary of the content on the page No. 20
Step3- Click “Active” to make the connection is ready. Step4- After successful connect between VC-200M and VC-200S, the information will show on channel status. 20
