Summary of the content on the page No. 1
11Mbps Wireless Internet Broadband Router
ANSEL 2314
Wireless BroadBand Router
User Guide
Version 1.3
0
Summary of the content on the page No. 2
11Mbps Wireless Internet Broadband Router The information in this guide may change without notice. The manufacturer assumes no responsibility for any errors which may appear in this guide. Fast Ethernet is a trademark of XEROX Corporation. Microsoft, Windows and Windows logo are trademarks of Microsoft Corporation. Copyright 2002. All right reserved. No Part of the contents of this guide maybe transmitted or reproduced in any form or by any means without the written permission of th
Summary of the content on the page No. 3
11Mbps Wireless Internet Broadband Router Regulatory information / Disclaimers Installation and use of this Wireless LAN device must be in strict accordance with the instructions included in the user documentation provided with the product. Any changes or modifications (including the antennas) made to this device that are not expressly approved by the manufacturer may void the user’s authority to operate the equipment. The manufacturer is not responsible for any radio or television int
Summary of the content on the page No. 4
11Mbps Wireless Internet Broadband Router Caution Statement of the FCC Radio Frequency Exposure This Wireless LAN radio device has been evaluated under FCC Bulletin OET 65C and found compliant to the requirements as set forth in CFR 47 Sections 2.1091, 2.1093, and 15.247(b)(4) addressing RF Exposure from radio frequency devices. The radiation output power of this Wireless LAN device is far below the FCC radio frequency exposure limits. Nevertheless, this device shall be used in such a ma
Summary of the content on the page No. 5
11Mbps Wireless Internet Broadband Router Contents 1: Introduction 1.1 Before You Start 1.2 System Requirement 1.3 How to Use this Guide 2: Hardware Installation 2.1 Product Description 2.1.1 Overview 2.1.2 Features 2.1.3 Front Panel 2.1.4 LEDs and Reset Button 2.1.5 Rear Panel 2.2 Installing the Router 2.2.1 Preparing for the installation 2.2.2 Getting Started 3: Configuration 3.1 Configuring the Wireless Access Point Router 3.2 The Setup Wizard 3.2.1 PPPoE Connection fo
Summary of the content on the page No. 6
11Mbps Wireless Internet Broadband Router 3.4.5 Backup 3.5 Setup the Advanced Features 3.5.1 LAN IP Setting 3.5.2 DHCP Setting 3.5.3 Firewall Setting 3.5.4 Privilege 3.5.5 Virtual Servers 3.5.6 Routing 3.5.7 WAN MAC Address Clone 3.5.8 DDNS Setting 3.5.9 MAC Control 3.6 Configuring your PCs to Connect to the Router 4: Specifications 4.1 Technical Specifications 4.2 Environmental Information 4.3 Standard Conformance 4.4 Cable Specifications Appendix A: About Static and Dynami
Summary of the content on the page No. 7
11Mbps Wireless Internet Broadband Router 1: Introduction The Wireless Internet Broadband Router combines the technology of Fast Ethernet and IEEE 802.11b Wireless LAN, providing the home or small office users the Cable/DSL access to the Internet via cord and cordless connection. At the same time, integrated with the firewall and 128-bit WEP (Wired Equivalent Privacy) Encryption, the Wireless Internet Broadband Router allows multiple users to share one Internet connection while ensuring
Summary of the content on the page No. 8
11Mbps Wireless Internet Broadband Router 1.3 How to Use this Guide This guide is structured as follows: Chapter 2, Hardware Installation explains the function of the router and how to physically install it. Chapter 3, Configuration explains how to set up and modify the configuration of the router with its Web-based utility. In addition, the configuration of the PCs that you want to connect to the Router can be found within this chapter. Chapter 4, Specifications contains informatio
Summary of the content on the page No. 9
11Mbps Wireless Internet Broadband Router 2: Hardware Installation 2.1 Product Description This chapter describes the features and functions of the router and shows how to physically install it. 2.1.1 Overview As the interface between WAN and LAN, the Wireless Internet Broadband Router combines the technology of Fast Ethernet and IEEE 802.11b Wireless LAN, providing the home and small office users the broadband access to the internet via cord and cordless connection. Meanwhile with
Summary of the content on the page No. 10
11Mbps Wireless Internet Broadband Router WAN Enables outside users to access the internal IP servers via Internet. Compatible with virtually all standard Internet applications Compatible with all standard internet application Enables administrators to block specific interior users’ Internet access 2.1.3 Front Panel The front panel of the router has 3 LEDs for each 10/100 Mbps ports, and three Module Status LEDs at the left. The Internet LEDs are at the right. Figure 2-1 show fron
Summary of the content on the page No. 11
11Mbps Wireless Internet Broadband Router Table 2-2 10/100 Port Status LED Functionality LED Color Function Lights to indicate a functional network link through the corresponding port with an attached device. Link/Act Green Blinks to indicate that the router is actively sending or receiving data over that port. Lights to indicate that the connection made through the corresponding port is running in Full Duplex mode. FULL/COL Green Blinks periodically to indicate that the connection
Summary of the content on the page No. 12
11Mbps Wireless Internet Broadband Router 2.1.5 Rear Panel The rear panel of the router has one Reset button at the left. At the right area are the Internet and LAN ports and a power connector. Figure 2-2 shows rear panels of these routers. Table 2-4 explains the function of the port. Figure 2-2 Rear panel of the Wireless Internet Broadband Router with Fixed Antenna and one Reverse SMA Antenna Reset Button Internet & LAN Ports DC Input Port
Summary of the content on the page No. 13
11Mbps Wireless Internet Broadband Router 2.2 Installing the Router This section will discuss what you should do before connecting your router to the network and how to physically install it. 2.2.1 Preparing for Installation Before you start to connect your router to any network device, make sure you get the following values from your ISP. You will need those values to setup the Router and configure you networked PCs to accept the IP address the Router chooses to assign them. P
Summary of the content on the page No. 14
11Mbps Wireless Internet Broadband Router 2.2.2 Getting Started You may complete the following steps to install your Wireless Internet Broadband Router when you have all the information mentioned above on hand. Step 1. Power all devices down. This should include your PCs, Cable or DSL modem and the Router. Step 2. Connect the Router to your PCs. A. Connect one end of a standard network cable to the 10/100 RJ-45 LAN ports on the back of the Wireless Access Point Router. B. Connec
Summary of the content on the page No. 15
11Mbps Wireless Internet Broadband Router 3: Configuration 3.1 Configuring the Wireless Access Point Router Once you’ve done with the hardware installation, you may start to configure your system. Note that this high-speed Wireless Router has an internal integrated-circuit chip that programs all the administrative utility. The utility can be accessed by any PC on the network at http://192.168.1.1 . Typing http://192.168.1.1 into the PC’s browser address windows. (See Figure 3-1)
Summary of the content on the page No. 16
11Mbps Wireless Internet Broadband Router Note: If you have completed the basic configuration of the router, you may refer to Section 3.6 Configuring your PCs to Connect to the Router to configure the PCs that you plan to connect to the Router. 3.2 The Setup Wizard Figure 3-3 shows the page that you will see once you have accessed to the Utility. The Setup Wizard of the router will lead you step by step to configure your Router. Please follow the instructions as the Wizard page re
Summary of the content on the page No. 17
11Mbps Wireless Internet Broadband Router Figure 3-3 The “Home” page of the Utility Menu Screen 3.2.1 PPPoE Connection for WAN If your ISP uses PPPoE (Point-to-Point Over Ethernet) to establish communications with end-users, you will receive information such as User Name and Password from them. To set up a PPPoE connection for WAN, follow the instructions as shown in Figure 3-4 Cable/DSL Setup Menu Screen and Figure 3-5 Cable/DSL Setup Menu with “No” Option Scr
Summary of the content on the page No. 18
11Mbps Wireless Internet Broadband Router - Max Idle Time The Max Idle time is the amount of time you would like to pass before the Router drops your Internet connection due to inactivity. Enter zero (0) in the field to remain Internet connection on at all time. The idle time ranges from 0 to 60 minutes. Figure 3-4 Cable/DSL Setup Menu Screen Figure 3-5 Cable/DSL Setup Menu with “No” Option Screen Figure 3-6 PPPoE Menu Screen 17
Summary of the content on the page No. 19
11Mbps Wireless Internet Broadband Router 3.2.2 Fixed IP for WAN If your ISP has assigned your home a static IP address (See Appendix A About Static and Dynamic IP Address), you may connect to the Internet by using a fixed, or static address. To set up a Fixed IP for WAN, do the following steps as an example. Step 1 Choose “YES” when you see the question: (See Figure 3-5 Cable/DSL Setup Menu with “No” Option Screen) Has your Internet Service Provider given
Summary of the content on the page No. 20
11Mbps Wireless Internet Broadband Router Figure 3-7 Cable/DSL Setup Menu Step 3 Enter the DNS Address. (See Figure 3-8 DNS Menu Screen) Your ISP should provide you with at least one DNS IP Address. If not, contact your ISP. Figure 3-8 DNS Menu Screen 19
