Summary of the content on the page No. 1
Installation Instructions
Discovery Wall Oven
EO, MOH and MOV Series
Part No. 65433 Rev. L
Summary of the content on the page No. 2
® All specifications are subject to change without notice. Dacor assumes no liability for changes to specifications. © 2007 Dacor, all rights reserved.
Summary of the content on the page No. 3
Table of Contents Before You Begin... ........................................................... 1 Planning the Installation ................................................... 6 Important Safety Instructions .......................................... 1 Selecting the Location ...................................................... 6 Important Information About Safety Instructions .............. 1 Cabinet Cutout ................................................................. 6 Safety Symbols an
Summary of the content on the page No. 4
Important Safety Instructions General Safety Precautions To reduce the risk of fire, electric shock, serious injury or death when using your appliance, follow basic safety precau- tions, including the following: WARNING WARNING • Read the accompanying use and care manual • To prevent injury due to the unit tipping forward, before operating this appliance. secure the oven to the cabinet using the supplied mounting screws. • Keep packaging materials away from children. Plastic sheets and ba
Summary of the content on the page No. 5
Customer Service Information If You Need Help... Model Identification If you have questions or problems with installation, contact your Dacor dealer or the Dacor Customer Service Team. EO230xxx For repairs to Dacor appliances under warranty call the Dacor Distinctive Service line. Whenever you call, have the model and serial number of the appliance ready. The model A B C D and serial number are printed on the product data plate. Dacor Distinctive Service (repairs under warranty only) A = M
Summary of the content on the page No. 6
Product Specifications Product Dimensions All tolerances: ±1/16 (±1.6 mm), unless otherwise stated. Model A B C D E F G H Number EO127 27” 25 3/8” MOH127 (68.6 cm) (64.4 cm) MOV127 27 15/16” 27 3/8” (71.0 cm) (69.5 cm) EO130 30” 28 3/8” MOH130 (76.2 cm) (72.1 cm) MOV130 23 3/8” 2 5/16” 7 3/8” 6 3/8” (59.4 cm) (5.9 cm) (18.7 cm) (16.2 cm) EO227 27” 25 3/8” MOH227 (68.6 cm) (64.4 cm) MOV227 51 1/16” 50 ½” (129.7 cm) (128.3 cm) EO230 30” 28 3/8” MOH230 (76.2 cm) (72.1 cm) MOV230 J K
Summary of the content on the page No. 7
Product Specifications Top of chassis C H 1 1/4” E D (3.2 cm) F G B Utility cutout L Control panel 66” (167.6 cm) front Flexible conduit J A K Top of Chassis notch chassis side view Single Wall Oven Dimensions Top of chassis C H 1 1/4” E D (3.2 cm) F Utility G B cutout L Control panel 66” (167.6 cm) front J Flexible conduit A K Top of Chassis notch chassis side view Double Wall Oven Dimensions 5
Summary of the content on the page No. 8
Planning the Installation Model Selecting the Location A B C Number • Carefully check the location where the oven is to be EO127 installed. The oven should be placed for convenient 25 ½” 27” 56 ½” MOH127 access, but away from drafts that may be caused by (64.8 cm) (68.6 cm) (143.5 cm) doors, windows, and heating, ventilation and air condi- MOV127 27” 7/16” tioning outlets. (69.7 cm) EO130 • Make certain that electrical power can be provided in 28 ½” 30” 62 ½” the selected location. B
Summary of the content on the page No. 9
Planning the Installation D NOt ES: • Cutout tolerances: +1/16 (1.6 mm), -0, unless otherwise stated. • 24” minimum cutout depth. Recommended Recommended • 3/4” support platform must be flush with electrical electrical front of cutout. See page 8. location location 1“ (2.5 cm) min. 4“ (10.2 cm) min. to bottom of between cutouts door Duel Single Wall Oven A A Cutout B B 3/4” (1.9 cm) 3/4” (1.9 cm) support platform support platform 1 ¾“ (4.5 cm) min. clear to top of door for heat Alternate
Summary of the content on the page No. 10
Planning the Installation Cabinet Cutout (Continued) Support Platform WARNING The top surface of the support platform must be installed flush with the cutout in the front of the cabinet or wall and any trim. Failure to install the platform properly may cause the exhaust vent to deform and/or become obstructed. An obstructed exhaust area may cause the oven to malfunction. See below. Provide a platform within the cabinet to support the oven. A properly supported piece of 3/4” (1.9 cm) thick
Summary of the content on the page No. 11
Planning the Installation It is the owner’s responsibility to ensure that a qualified Electrical Specifications electrician performs the electrical connection of this appli- ance. The electrical installation, including minimum supply wire size, must comply with the National Electric Code IMPORt ANt ANSI/NFPA 70 (latest revision) and local codes and ordi- • Preheat times and cavity temperature recovery times nances. will be increased slightly if operating on less than a A copy of this stan
Summary of the content on the page No. 12
Installation Instructions 1. Before proceeding, turn off power to the circuit to which Electrical Service Installation the oven will be connected at the circuit breaker or fuse box. 2. Position the oven directly in front of the cabinet cutout. WARNING 3. Feed the appliance conduit into the electrical junction • Wire the oven only in compliance with local ordinanc- box and attach it using a UL approved strain relief. es. 4. Depending upon local codes, utilize one of three meth- • If the ele
Summary of the content on the page No. 13
Installation Instructions Connecting to a Three (3) Wire Electrical Connecting to a Three (3) Wire Electrical System - Where Local Codes Permit System with External Ground - Where Local Codes Permit WARNING WARNING Do not connect the green appliance conduit wire to the neutral (white) junction box wire unless local building • Do not connect the green appliance wire to the junc- codes permit. tion box or to a cold water pipe unless local building 1. Separate the wires coming out of the ap
Summary of the content on the page No. 14
Installation Instructions Connecting to a Three (3) Wire Electrical System with External Ground - Where Local Codes Permit (Continued) Cable from circuit Separate No. 10 min. breaker panel or copper grounding wire fuse box Wire nut Junction box (4 places) RED WHITE RED WHITE GREEN Clamp must be BLACK GREEN tight on pipe BLACK Conduit to wall oven t hree (3) Wire Connection with External Ground Final Installation WARNING • A minimum of two people are required to safely install this appl
Summary of the content on the page No. 15
Installation Instructions 3. Raise the door so that it is at a 15° angle from the front 2. Support the oven at all times until it is secured into the of the oven. Hold the door with one hand on each side. cabinet. Be certain to take all necessary safety precau- Lift the door up and out. tions. 3. Resting the oven on the cabinet support platform, slide the oven into the recessed area until the rear edge of the oven trim post is flush with the cabinet face and the oven is centered within the c
Summary of the content on the page No. 16
Installation Instructions 1. Grasp the oven door on opposite sides and hold it at a Install Exhaust Deflector 15° angle from the front of the oven. See facing page. CAUt ION 2. Slide the hinges into the hinge openings, resting the bottom of the hinge arms on the hinge receptacles. Install the exhaust deflector before installing the oven 3. Continue to hold the door at a 15° angle with one hand door(s). while pushing in on each of the bottom corners of the Attach the exhaust deflector to
Summary of the content on the page No. 17
Installation Instructions Lower lip of hinge receptacle Notch on bottom of hinge Door Installation □ Plastic coating, if applicable, has been removed from Installation Checklist outside of oven. □ All packaging materials have been removed from inside WARNING the oven. • To ensure a safe and proper installation, the follow- □ Power is turned on at circuit breaker or fuse box. ing checklist should be completed by the installer to ensure that no part of the installation has been over- □ Pr
Summary of the content on the page No. 18
Notes 16
Summary of the content on the page No. 19
Summary of the content on the page No. 20
Dacor ● 600 Anton Blvd. Suite 1000 Costa Mesa, CA 92626 ● Phone: (800) 793-0093 ● Fax: (626) 403-3130 ● www .Dacor .com
