Summary of the content on the page No. 1
3
3 ⁄16" PORTABLE PLANER
MODEL G9003
INSTRUCTION MANUAL
COPYRIGHT ©2000 BY GRIZZLY INDUSTRIAL, INC.
1821 VALENCIA ST., BELLINGHAM, WA 98227
WARNING: NO PORTION OF THIS MANUAL MAY BE REPRODUCED IN ANY SHAPE
OR FORM WITHOUT THE WRITTEN APPROVAL OF GRIZZLY INDUSTRIAL, INC.
APRIL, 2000 PRINTED IN U.S.A.
Summary of the content on the page No. 2
-2- G9003 Portable Planer
Summary of the content on the page No. 3
SAFETY For Your Own Safety Read Instruction Manual Before Operating This Equipment The purpose of safety symbols is to attract your attention to possible hazardous conditions. This manual uses a series of symbols and signal words which are intended to convey the level of importance of the safety messages. The progres- sion of symbols is described below. Remember that safety messages by them- selves do not eliminate danger and are not a substitute for proper accident pre- vention measures. Indica
Summary of the content on the page No. 4
Safety Instructions For Power Tools 9. USE PROPER EXTENSION CORD 13. DON’T OVERREACH. Keep prop- for the tool. Make sure your exten- er footing and balance at all times. sion cord is in good condition. 14. MAINTAIN TOOLS WITH CARE. Conductor size should be in accor- Keep tools sharp and clean for dance with the chart below. The best and safest performance. amperage rating should be listed on Follow instructions for lubricating the motor or tool nameplate. An and changing accessories. undersized
Summary of the content on the page No. 5
Safety Instructions For Portable Planers 5. DO NOT REMOVE EXCESSIVE 1. USE ONLY FOR WOOD. This AMOUNTS OF WOOD IN A SINGLE machine is not designed to process PASS. Better results can be any material other than wood. achieved by taking multiple passes with a small amount of material 2. ALWAYS KEEP FINGERS AND removal in each pass. HANDS AWAY FROM ROTATING CUTTERHEAD. Never attempt to 6. INSPECT STOCK THOROUGHLY clear chips away from the base of BEFORE PLANING. Look stock the chip chute when the m
Summary of the content on the page No. 6
CONTROL LOCATION Control Location Specifications Speed: 15000 RPM Refer to Figure 1 for the location of the key components and controls of this Planer. Motor Type: Universal Brush Motor Become familiar with the controls and the 1 Motor Power: ⁄2 HP, 110V, 5.0 Amp adjustments before operating the Planer. Cutterhead: 2 Blades 3 Maximum Cutting Width: 3 ⁄16" 1 Maximum Stock Removal/Pass: ⁄32" 11 Maximum Rabbet Depth: ⁄32" Weight: 5.75 lbs Accessories Included: Fence, Blade Removal Wrench, Sharpenin
Summary of the content on the page No. 7
BLADE ADJUSTMENT & REMOVAL the amount of contact is the same all the way across. 3. If there is too much contact, or Turn the switch off and unplug the none at all, at any point across the Planer from power before attempting blade, then the blade needs to be blade removal or any adjustments. reset. Refer to Blade Installation Serious injury may occur if the unit Section. should be accidentally started while checking or removing the blades. 4. Repeat procedure for the other Blade. The Planer come
Summary of the content on the page No. 8
BLADE INSTALLATION 4. Set the Blade/Back Plate Assembly onto the Cutterhead. Make sure the bottom edge of the Turn the switch off and unplug the Back Plate is positioned into the Planer from power before attempting slot on the Cutterhead. See blade installation or any adjustments. Figure 5. Serious injury may occur if the unit should be accidentally started while installing the blade. Make certain edge of back plate engages in slot in cutterhead The Blade must be mounted to the Back Plate using
Summary of the content on the page No. 9
BLADE SHARPENING The Blade must be completely removed from the Planer and from the Back Plate in order for it to be safely sharpened. Follow the preceding instructions for Blade Removal. For the best results, have planer blades sharpened by a professional sharpening service which has the grinding and mea- surement equipment to assure that the Fig 6. Blades in Sharpening Jig. blade cutting geometry is maintained at optimum levels. It is a procedure which 3. The bevel edge of the blades will requi
Summary of the content on the page No. 10
OPERATIONS 3. Turn the Planer on by pulling the Setting Cutting Depth ON/OFF trigger. Allow the cutter- head to achieve full speed before Lay a straightedge across the Rear Foot engaging the workpiece. and extend it across the Front Foot. Rotate 4. Once the cutting begins, push the the cutterhead so neither of the blades are Planer firmly across the workpiece touching the straightedge. Turn the Depth at the same rate of speed. Do not Adjustment Knob until the Front and Rear stop the Planer’s pro
Summary of the content on the page No. 11
OPERATIONS successive passes to achieve the full Chamfering depth of the rabbet as the maximum depth 1 of cut is ⁄32" per pass. The maximum rab- The Front Foot has a V-groove machined 11 bet depth is ⁄32". See Figure 8. into it to allow for edge chamfering. Position the Planer on the corner of the To Perform Rabbeting Operations: workpiece, with the V-groove seated on 1. Secure the workpiece firmly with the corner. See Figure 7. Be sure the clamps to eliminate movement workpiece is firmly secure
Summary of the content on the page No. 12
MAINTENANCE Maintenance Brush Replacement The universal motor has two brushes Your 110 V Portable Planer will give you which may periodically need replacement. hundreds of hours of operation time before When checking or replacing the brushes, ever needing service. This product is dou- make sure the slots the brushes fit into are ble insulated which provides protection clear of grit or debris so the brushes are from electrical shock should a problem free to move in and out. ever develop with grou
Summary of the content on the page No. 13
OPERATING TIPS Operating Guides and Tips Avoid overloading the planer. Do not Operating this equipment has the apply downward pressure to the tool potential to propel debris into the air while using. Do not feed into the which can cause eye injury. Always work so rapidly that it causes the wear safety glasses or goggles when motor to bog down. operating equipment. Be certain the safety glasses you wear meet the appropriate standards of the Ensure the safety of the workplace. American National S
Summary of the content on the page No. 14
-14- G9003 Portable Planer
Summary of the content on the page No. 15
Ref. # Part # Description Ref. # Part # Description 001 P9003001 Pan Hd Screw M4 x 16 029 P9003029 Brush Holder Cap 002 P9003002 Chip Cover 030 P9003030 Indication Plate 003 P9003003 Knob 031 P9003031 Screw M5 x 10 004 P9003004 Scale Plate for Knob 032 P9003032 Compression Spring 005 P9003005 Flat Washer 10mm 033 P9003033 Rubber Packing 006 P9003006 Main Frame 034 P9003034 Front Base 007 P9003007 Rivet 035 P9003035 Pan Hd Screw M5 x 18 008 P9003008 Name Plate 036 P9003036 Bas
Summary of the content on the page No. 16
TROUBLESHOOTING SYMPTOM POSSIBLE CAUSE CORRECTIVE ACTION Motor will not start. 1. Low voltage. 1. Check power line for proper voltage. 2. Brushes worn or sticking. 2. Replace both brushes. 3. Open circuit in motor or loose 3. Inspect by qualified connections. electrical technician. Motor will not start; 1. Short circuit in line cord or 1. Inspect cord or plug for fuses or circuit breakers plug. damaged insulation blow. and shorted wires. 2. Short circuit in motor or loose 2. Inspect by qualified
Summary of the content on the page No. 17
WARRANTY CARD Name__________________________________________________________ Street__________________________________________________________ City____________________State________Zip_________ Phone Number____________E-Mail___________________FAX____________ MODEL # G9003 Portable Planer__ Order #_______________________ The following information is given on a voluntary basis. It will be used for marketing purposes to help us develop better products and services. Of course, all information is stric
Summary of the content on the page No. 18
Send a Grizzly Catalog to a friend: Name________________________________ Street________________________________ City______________State______Zip_______ FOLD ALONG DOTTED LINE GRIZZLY INDUSTRIAL, INC. P.O. BOX 2069 BELLINGHAM, WA 98227-2069 TAPE ALONG EDGES--PLEASE DO NOT STAPLE
Summary of the content on the page No. 19
NOTES -19- G9003 Portable Planer
Summary of the content on the page No. 20
WARRANTY AND RETURNS Grizzly Industrial, Inc. warrants every product it sells for a period of 1 year to the original purchaser from the date of purchase. This warranty does not apply to defects due directly or indirectly to misuse, abuse, negligence, accidents, repairs or alterations or lack of main- tenance. This is Grizzly’s sole written warranty and any and all warranties that may be implied by law, including any merchantability or fitness, for any particular purpose, are here- by limited to
