Summary of the content on the page No. 1
JCD3010
MOBILE CD PLAYER / RECEIVER
Installation and Operation Manual
JCD3010
Summary of the content on the page No. 2
JCD3010 SAFETY INFORMATION DISC NOTES When Driving Compatible Disc Types Keep the volume level Iow enough to be aware of your surroundings. Table 1: General Disc Information When Washing your Vehicle Do not expose the product directly to water, as this can cause electrical shorts, fire or other Diameter/ damage. Disc Type Logo Playback Time Playable Sides When Parked Audio CD 12 cm single side 74 minutes Exposure to direct sunlight for an extended period of time can produce very high temperatur
Summary of the content on the page No. 3
JCD3010 problem is corrected. Once proper operation is achieved, turn the ignition switch off and INSTALLATION proceed with final mounting of the chassis. Before You Begin 7. Carefully slide the radio into the mounting sleeve making sure it is right-side-up until it is fully seated and the spring clips lock it into place. 1. Disconnect Battery 8. Attach one end of the Before you begin, always disconnect the battery negative terminal. perforated support strap Dashboard 2. Remove Transport Scr
Summary of the content on the page No. 4
JCD3010 WIRING A- A 15A FUSE SHOWN FROM PIN VIEW A-A Wire Connector ACCESSORY/IGNITION (+) MEMORY/BATTERY (+) Connect to existing radio accessory fuse or Connect to battery or 12 volt power source +12 VDC switched power source. that is always live. The radio will not work if this wire is not connected. POWERANTENNA Connect to power antenna or amplifier. If not GROUND used, tape bare end of wire. Connect to ground terminal or clean, unpainted metal part of chassis. 4
Summary of the content on the page No. 5
JCD3010 3. Press MODE again to cancel Aux In mode and return to previous mode. BASIC OPERATION Reset After releasing the control panel, use a pencil or any non-metallic object to press and hold the 7 6 5 21 4 19 3 1 12 2 RESET button (17) for five seconds to reset the main unit. The unit will return to the factory default settings. The reset button should be activated for the following reasons: • initial installation of the unit when all wiring is completed JCD3010 9 • function buttons do not
Summary of the content on the page No. 6
JCD3010 Display Selector (DISP) TUNER OPERATION This unit can display either the clock time or radio frequency/CD player functions. Press the DISP button (6) on the control panel or remote control to display the time for approximately 5 6 1 12 7 5 21 4 19 3 2 seconds. The correct time of day can be set by pressing and holding the DISP button. Setting the Clock To set the clock, perform the following steps: JCD3010 1. Press the DISP button (6) to display the clock. 9 2. Press and hold the DISP
Summary of the content on the page No. 7
JCD3010 Automatically Store / Preset Scan (AS/PS, AMS) CD OPERATION Automatically Store Select a band (if needed). Press the AS/PS button (16) on the control panel (or the AMS button 6 5 21 4 1 12 7 19 3 2 on the remote control) for more than three seconds to automatically select six strong stations and store them in the current band. The new stations replace any stations already stored in that band. JCD3010 Preset Scan 9 Select a band (if needed). Press the AS/PS button (16) on the control p
Summary of the content on the page No. 8
JCD3010 SPECIFICATIONS TROUBLESHOOTING CD S/N Ratio. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . > 70dB Symptom Cause Solution Sampling Frequency . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 44.1Khz No power The vehicle’s power is not If the power supply is properly Quantization Bits . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .
Summary of the content on the page No. 9
JCD3010 9
Summary of the content on the page No. 10
ASA Electronics Corporation www.asaelectronics.com www.jensenrvdirect.com © 2010 ASA Electronics Corporation v. 092209
