Summary of the content on the page No. 1
SmartDome Camera
SCC-C6405(P)
E
Owner’s Instructions
D
Benutzerhandbuch
F
Manuel d’instruction
Es
Manual del usuario
I
Istruzioni per l’uso
Part : AB68-00504B (02)
Printed in China
Summary of the content on the page No. 2
Important Safety Instructions Safety Precautions 1. Read these instructions. The purpose of this information is to ensure proper use of this product to 2. Keep these instructions. prevent danger or damage to property. Please be sure to observe all 3. Heed all warnings. precautions. 4. Follow all instructions. * The precautions are divided into "Warnings" and "Cautions" as 5. Do not use this apparatus near water. distinguished below: 6. Clean only with dry cloth. Warning: Ignoring this warning ma
Summary of the content on the page No. 3
6. Do not place conductive objects (e.g., screwdrivers, coins, and metal FCC STATEMENT things) or containers filled with water on top of the camera. (Doing so may cause personal injury due to fire, electrical shock, or falling objects.) This device complies with Part 15 of the FCC Rules. Operation is subject to 7. Do not install the unit in humid, dusty, or sooty locations. the following two conditions: (Doing so may cause fire or electrical shock.) (1) This device may not cause harmful interf
Summary of the content on the page No. 4
Before Usage This is a basic instruction manual for the SCC-C6405(P) user. It contains all the instructions needed to use the SCC-C6405(P) from a simple introduction of the control locations and functions of the SCC-C6405(P) to installation methods in the set up menu. We recommend all users of the SCC-C6405(P) from the E advanced user who has used similar cameras before to the general user to read the instruction manual before using. The most frequently used feature in the SCC-C6405(P) would b
Summary of the content on the page No. 5
Table of contents 4. ZONE SET ..................................................................................3-17 Before Usage...............................................................................................1-1 - PRIVACY ZONE .......................................................................3-17 - STYLE.......................................................................................3-17 Chapter 1 SCC-C6405(P) Overview ................................................
Summary of the content on the page No. 6
SCC-C6405(P) Introduction Chapter 1 SCC-C6405(P) Overview SCC-C6405(P) is a zoom lens built in smart dome camera which provides you with the best monitoring function in connection with In this chapter we will briefly introduce the SCC-C6405(P) and CCTV at banks or companies. E show main functions, locations of control and Switch Setting. The SCC-C6405(P) is a high quality surveillance camera using x22 zoom lens and digital zoom IC, it can catch clear images up to 220 times. SCC-C6405(P) has a
Summary of the content on the page No. 7
Locations of Control FRONT BACK AC 24V OUT POWER E AC 24V OUT POWER 1-7 1-8
Summary of the content on the page No. 8
ADAPTER CONNECTION INITIAL SETTING CAMERA ADDRESS SETUP Use SW701, SW702, or 703 for Camera Address setup. You may allocate up to 255 addresses by using SW701 to set the 3rd digit, SW702 the 2nd digit, and SW703 the 1st digit. EX) In case of Camera Address 1, see the following figure for setup. SCC-C6405(P) Adapter BOARD E SW701 SW702 SW703 Setting communication Protocol Use number 1~4 PIN of SW704 to set communication Protocol. PIN PIN1 PIN2 PIN3 PIN4 Comp A : SAMSUNG HALF A OFF OFF OFF OFF B :
Summary of the content on the page No. 9
Setting RS-422A/RS-485 termination Chapter 2 SCC-C6405(P) Installation 12 As it is shown in the structure map, when Controller and RS-422A/RS- 485 is connected it should be terminated according to the Cable feature E of impedance on the each end of the transmitting line to transfer the In this chapter, we will check the contents of the package before signals in long distance by controlling the reflection of the signals to the installing the SCC-C6405(P), and prepare a power adapter suitable lo
Summary of the content on the page No. 10
Before Installing Preparing the Cables To install and use the SCC-C6405(P), the following cables should be Checking Package Contents prepared. Please check that all components listed below are included in the package: Power Adapter Cable The cable that plugs into the SCC-C6405(P) power input receptacle has the rated voltage of AC24V, 1.5A. E Check the rated voltage before using the cable. SCC-C6405(P) Bracket anchor Owner’s Instructions AC 24V OUT Video Cable POWER The SCC-C6405(P)'s cable is
Summary of the content on the page No. 11
Cable Connection Installing SCC-C6405(P) 1. First, connect one end of the Installation Precautions BNC video cable connector to the Video Output Terminal 1) Make sure that the installation site can sufficiently support a minimum of (VIDEO OUT) four times the net weight of the SCC-C6405(P) SmartDome Camera and other accessories. 2. Then, connect the other end of 2) Install in an area where the space above the ceiling board is over 18 cm the connector to the Video Input E (7 in.) high. Terminal
Summary of the content on the page No. 12
5) CEILING MOUNT ADAPTOR (SADT-100CM) 3) INDOOR HOUSING (SHG-120) This adaptor is used for installing the indoor housing or the outdoor This housing is used for installing the SmartDome Camera to an indoor housing for the SmartDome Camera to a concrete ceiling. wall or a ceiling. E 6) POLE MOUNT ADAPTOR (SADT-100PM) 4) OUTDOOR HOUSING (SHG-220) This adaptor is used for installing the WALL MOUNT ADAPTOR This housing is used for installing the SmartDome Camera to an (SADT-100WM) to a pole that is
Summary of the content on the page No. 13
Installing the Camera 5. [Figure 5] Match the 6. Pull the safety wire from the case BRKT-ANCHOR and CAMERA body, and assembly it to the ADAPTER and use 4screws camera holder. 1. [Figure 1] Install the structure on the (PH M4 x 8) to assemble them. ceiling. (Refer to Installation reference for the Length of the structure) [Figure 5] [Figure 6] * Built in by the builder of the structure E [Figure 1] Length of ceiling Hole 2. Make a hole in the ceiling where the camera will be installed. (The ho
Summary of the content on the page No. 14
Structure of the Setup Menu CAMERA SET CAMERA ID ON.../OFF Chapter 3 Setup Menu Overview V-SYNC INT/LINE... COLOR/BW COLOR/BW.../AUTO... MOTION DET ON.../OFF ZOOM SPEED 1/2/3/4 In this chapter, we will look over the Setup Menu of the DIGITAL ZOOM OFF/X2~X10 E EXIT QUIT/SAVE/PRESET SCC-C6405(P), First we'll look over the overall structure of the Setup Menu, and then we'll look at the functions of each menu. VIDEO SET IRIS ALC.../WDR... SHUTTER OFF/1/100(1/120)~1/1OK/AUTOX2~X160 AGC OFF/LOW/HI
Summary of the content on the page No. 15
❈ If the power is turned off after PRESET, AUTO PAN, SCAN, ALARM SET ALARM PRIORITY SET ALARM1 1~4 PATTERN function is activated and no other control is made, camera ALARM2 1~4 will do the same function after the power is turned on. ALARM3 1~4 ALARM4 1~4 ❈ Menu setting is available only when tilt position is under 90°. EXIT QUIT/SAVE When tilt position is over 90° and menu-on command is received, pan will automatically rotate 180° and tilt will be move to the ALARM IN
Summary of the content on the page No. 16
(CAMERA SET) (CAMERA ID) COLOR/BW A B C D E F G H I J K L In the COLOR/BW menu, you can switch ON or OFF the IR (infrared) Filter. CAMERA ID ON... M N O PQ R S T U V W X V-SYNC INT ➜ In a poor illumination environment, the IR filter is turned off in the BW mode the its Y Z 0 1 2 3 4 5 6 7 8 9 COLOR/BW COLOR sensitivity increases as high as a black and white camera. On the other hand, the MOTION DET OFF Press : ! - + ✽ ( ) / ZOOM SPEED 3 SP ï î SP IR filter is turned on and the sensitivity d
Summary of the content on the page No. 17
MOTION DET ZOOM SPEED In MOTION DET, you can set the Motion Detection function, Motion Detection In the ZOOM SPEED menu you can select the speed of the ZOOM Key Sensitivity, and the Area of Motion Detection. If the Motion Detection function (Tele/Wide). is set, the movement of an intruder can be detected. When motion is detected, Use the [Left] or [Right] keys in the ZOOM SPEED menu to select it sets off the Alarm signal of the Controller. the speed. 1 : Magnification x 22 takes about 18 s
Summary of the content on the page No. 18
- LEVEL 1 : Controls the shutter speed while WDR operates. 2. VIDEO SET MENU - LEVEL 2 : Controls the whole brightness while WDR operates. - FLIKERLESS : This is for preventing flicker on the screen when NTSC IRIS system is used in 50HZ power supply region and PAL system is used in There is a function to automatically adjust IRIS to the incoming light level. 60HZ power supply region. That is to prevent shaking on the screen Owing to this function, you may set up the brightness level yourself. re
Summary of the content on the page No. 19
AGC WHITE BAL The AGC menu was designed to provide you with brighter screen Lights are generally denoted as color temperatures and expressed in supposed you photographed any subject in the dark resulting in less Kelvin (K) units. brighter image than regulated. AGC menu setup is available only when The general light color temperatures are shown below. the SHUTTER menu is set to Fast Shutter or Off. Press either Left and Right to go to LOW or HIGH and the AGC function will be activated. LOW is
Summary of the content on the page No. 20
You can select one of four modes for white balance adjustment as follows: FOCUS MODE In the FOCUS MODE MENU, the Focus method can be set to AF, MF, or ONEAF. - ATW1/ATW2(Auto-Tracing White Balance Mode): In these modes, the - AF : With AUTO FOCUS MODE, you can monitor the screen continuously color temperature is monitored continuously and thereby white balance is and it will focus automatically. While moving the zoom keys, it will set automatically. The following are the approximate supported co
