Summary of the content on the page No. 1
0
Summary of the content on the page No. 2
Contents Contents…………………………………………………………………………………………………1 Function Description: ………………………………………………………………………………….2 Notice for use…………...………………………………………………………………………………2 System requirements…………………………………………………………………………………..4 Start to use………………………………………………………………………………………………5 1. Appearance and Buttons………………………………………….……………………5 2. Basic operation…………………………………………………………………….……7 Application of Attached ArcSoft VideoImp
Summary of the content on the page No. 3
Function Description Welcome to purchase and use this digital video camera. Before use, please read this user manual carefully. With this digital video camera, you can take video clips and still photo. With the playback function, you can playback the taken video with this digital video camera; in addition, you can download the video from the digital video camera into your PC. When prepared, this user manual refers to the
Summary of the content on the page No. 4
5. These memory cards cannot be used for permanent storage of data. You must copy the documents in the digital video camera in the proper storage position. 6. When storing documents into the memory or the memory card, make sure that the size of the documents does not exceed the capacity of the memory. Maintenance and care: 1. In use, always wear the wrist band so as to prevent slip. 2. Use proper protection sheath to avoid scratching the lens and screen. 3. To clean the lens, first
Summary of the content on the page No. 5
System requirements When operating and using this digital video camera, be sure to meet the requirements on the basic system for computer. It is strongly recommended to use the best computer units to operate the camera so as to bring its functions into full play. Below are the requirements on the basic system: Operation System Microsoft Windows 2000,XP, vista, Windows7 CPU Above Intel PIII667 or CPU of equal performance
Summary of the content on the page No. 6
Start to use 1. Appearance and Buttons LCD Up key Shutter/OK key Mode key Delete key Left key Right key Down key 5
Summary of the content on the page No. 7
USB Connector Lens USB Switch TV Out Port Busy LED Microphone Power Key Speaker HDMI Out Port SD/MMC Card Slot Battery Cover Tripod Strap Holder 6
Summary of the content on the page No. 8
2. Basic operation 2.1 Install battery Press / slide down the Battery Cover and insert lithium battery. Align with correct polarity of battery terminals. Close the Battery Cover. 2.2 Charge Battery 1. Power off the camera. 2. Connect the camera to the computer USB port or the power adapter (not include) with USB cable to charge the battery. 3. During charging, Busy light is on and will be off when the battery is fully charged. 2.3 Use SD/MMC/SDHC card Insert the SD Memory card int
Summary of the content on the page No. 9
camera. Push and release inserted card if you wish to remove or replace the card. Turn your camcorder OFF before inserting / removing the SD Card. - Note that the SD Card has a tiny LOCK switch on the side. Set the switch to un-LOCK position to be able to store recorded videos, still pictures on inserted SD Memory Card. 2.4 Power on/off In power-off state, press and hold the power key to power on the camera. In power-on state, press the power key to power off the camera. In power-o
Summary of the content on the page No. 10
press the up key or down key to adjust the value. at this mode, you can view the Firmware version too. 2.6 Change mode After power on, it will enter video record mode, press MODE key to change mode between video record, Still photo record, Playback; 2.7 Video record In Video record mode, press shutter key to start video recording, While recording, press the shutter key again to stop recording. At preview mode, press Left or Right key can change the video size between HD(1280x720), D1
Summary of the content on the page No. 11
Note: While the memory is full or the SD card was locked, when you press the Shutter key, the camera will can not recording. Before inert or remove the card, please turn off the camera first. 2.9 Playback videos or photos Press mode key continuously to change playback mode, press ◄ key or ► key to select another file. After you select one video file, Press OK key to begin play video, during playing video, press and hold ► or ◄ key to fast forward or backwards playing v
Summary of the content on the page No. 12
2.10 V output After the camera is powered on, insert the terminal of the TV cable into the TV output port of the camera, the yellow port of the other terminal should be connected to VIDEO IN port of TV ， red(or white) port of the other terminal should be connected to AUDIO IN port of TV. 2.11 HDMI output If you want to output the image and sound in video camera to HD TV, please insert the HDMI cable (Optional) to the HDMI interface of the video camera, connect the other terminal
Summary of the content on the page No. 13
3 Delete files When in preview or playback mode. Press the Delete key will enter Delete menu mode, use direction key of Up or Down to select “Delete current” or “Delete all” . Select “Delete current” then press OK key will delete current image; if select “Delete all” the press OK key will delete all images, if press Delete key will exit deletion. 4 Connect to PC 1. Slide the USB Switch UP to extend the USB connector. And turn the camcorder ON. 2. Insert camcorder USB connector into
Summary of the content on the page No. 14
▲ Open USB port ▲Connect camera to PC (1) ▲ Connect camera to PC (2) 13
Summary of the content on the page No. 15
Application of Attached ArcSoft MediaImpression There are two software in CD provided for image processing: Xvid codec, MediaImpression Introduction interface for software installation Put the CD attached into the CD-ROM of the computer, then the following menu will occur: If the CD driver does not automatically carry out or close such function, please click autorun.exe 14
Summary of the content on the page No. 16
program under the root directory of the CD. Xvid codec Installation Instal Xvid codec: Click ” Install Xvid codec “ button and complete the installation as per the tips. 15
Summary of the content on the page No. 17
16
Summary of the content on the page No. 18
Notice: This software can be find in attached CD, If you want to play recorded video on your computer, please install Xvid codec, if your computer have install Xvide codec, this operation may do not it. MediaImpression Installation and Use: Install Mediainpression: Click “Install MediaImpression” button and complete the installation as per the tips. 17
Summary of the content on the page No. 19
18
Summary of the content on the page No. 20
After installation, please restart the computer. Run MediaImpression : Double click the icon on the desktop or follow “Start → Programs” to open: MediaImpression After starting MediaImpression, click the “Import” to import the media. 19
