Summary of the content on the page No. 1
AC4074, AC4072
Summary of the content on the page No. 2
2
Summary of the content on the page No. 3
3 1 K A 1 2 3 4 5 6 7 8 B L C D E M N O P F G H 9 I 10 J
Summary of the content on the page No. 4
4
Summary of the content on the page No. 5
English 6 繁體中文 23 简体中文 38 AC4074, AC4072
Summary of the content on the page No. 6
6 English introduction Congratulations on your purchase and welcome to Philips! To fully benefit from the support that Philips offers, register your product at www.philips. com/welcome. With this new CleanAir System you breathe cleaner air. For the best results, place the CleanAir System in a room where you spend most of your time, e.g. the living room or bedroom. Wherever there are people, plants or pets, there are airborne particles that can affect your well-being, especially if you suffer
Summary of the content on the page No. 7
English 7 K Control panel 1 Light sensor for night mode 2 AIR QUALITY on/off button with light 3 Power on/off button 4 SILENT button with light 5 Power-on light 6 FAN SPEED button with light 7 AUTO button with light 8 Fan speed lights (1, 2, 3 and boost power)/filter replacement lights 9 FAN SPEED indications 10 REPLACE FILTER indications l Filter 4: HEPA filter M Filter 3: activated carbon filter n Filter 2: formaldehyde filter (supplied with AC4074) or multi-care filter (supplied with A
Summary of the content on the page No. 8
8 English - Always place and use the appliance on a dry, stable, level and horizontal surface. - Leave at least 20cm free space behind and on both sides of the appliance and leave at least 30cm free space above the appliance. - Do not place anything on top of the appliance and do not sit on the appliance. - Do not place the appliance directly below an air conditioner to prevent condensation from dripping onto the appliance. - Make sure all filters are properly installed before you switch on
Summary of the content on the page No. 9
English 9 Note: Make sure you insert the filters in the correct position. 1 Place y our fingers in the r ecesses o f the side panels and gentl y pull the top par t of the fr ont panel to war ds y ou. Then lift the hooks at the bottom of the panel out of the bottom of the a ppliance . 2 Remo v e all the filters fr om the a ppliance . 3 Remo v e all packaging material fr om the filters. 4 Put filter 4 (HEP A filter) back into the a ppliance . Note: Make sure that the side wi
Summary of the content on the page No. 10
10 English 6 Put filter 2 (f ormaldeh yde filter f or A C4074 or m ulti-car e filter f or A C4072) back into the a ppliance . Note: Make sure that the side with the tag is pointing towards you. 7 Place filter 1 (pr e-filter) in the a ppliance . Note: Make sure that the side with the two projections is pointing towards you. Note: Make sure that all hooks are properly attached to the appliance. 8 T o r eatta ch the fr ont panel, inser t the bottom hooks into the botto m of
Summary of the content on the page No. 11
English 11 , The air quality light ring sho ws the quality of the air . Air quality indication Colour Air quality Blue very good Deep purple good Purple fair Red bad To switch off the air quality light ring, press the AIR QUALITY button. Note: The air quality light ring automatically goes on when the appliance is switched on. , The a ppliance automaticall y star ts operating in the A UT O mode . To switch off the appliance, press and hold the on/off button again until the power-on light goe
Summary of the content on the page No. 12
12 English adjust the sensitivity of the air quality sensor. When it is set to a higher sensitivity level, the appliance already starts cleaning the air at lower pollution levels to make the air even cleaner. There are 3 sensitivity levels: - standard - sensitive - extra sensitive The pollution sensor is set to standard sensitivity. You can adjust the sensitivity of the air quality sensor in the following way: 1 If the a ppliance is alr eady plugge d in, unplug the a ppliance and wait f
Summary of the content on the page No. 13
English 13 2 Pr ess the A UT O button to activ ate the auto mode . Note: When the appliance is operating in another mode and you want to activate the auto mode, simply press the AUTO button. , The A UT O light g oes on. , The F AN SPEED light indicates at which fan speed the a ppliance is operating. Note: When the air quality is very good and the appliance operates at a very low fan speed, the FAN SPEED light for the lowest speed setting does not go on. In this case only the power-o
Summary of the content on the page No. 14
14 English , A C4074 onl y: The cor r esponding fan speed light in the fan speed indicator g oes on. Note: Select boost power if you need an extra strong airflow when the air in the room is very dirty. All three fan speed lights go on. silent mode When you use the appliance in silent mode, it operates very quietly. 1 Pr ess and hold the on/off butto n f or 2 seconds to s witch on the a ppliance . 2 Pr ess the SILENT button to act ivate the silent mode . , The SILENT light g oes
Summary of the content on the page No. 15
English 15 Pre-filter The pre-filter is washable. - Clean the pre-filter when the first filter replacement light flashes to ensure optimal functioning of the appliance. 1 Place y our fingers in the r ecesses o f the side panels and gentl y pull the top par t of the fr ont panel to war ds y ou. Then lift the hooks at the bottom of the panel out of the bottom of the a ppliance . 2 T o r emo v e the pr e-filter , grab th e tw o pr ojections and pull the filte r to war ds y ou. 3 W
Summary of the content on the page No. 16
16 English Air quality sensor Clean the air quality sensor every 2 months for optimal functioning of the appliance. Clean it more frequently if you use the appliance in a dusty environment. Note: When the humidity level in the room is very high, it is possible that condensation develops on the air quality sensor. As a result, the AIR QUALITY light on the control panel and the air quality light ring may indicate that the air quality is bad even though the air quality is good. In this case y
Summary of the content on the page No. 17
English 17 - Filter replacement light 1 flashes: filter 1 (the pre-filter) has to be cleaned. See chapter ‘Cleaning’ for further instructions. - Filter replacement light 2 flashes: filter 2 (the formaldehyde filter (supplied with AC4074) or multi-care filter (supplied with AC4072)) has to be replaced. - Filter replacement light 3/4 flashes: the activated carbon filter and the HEPA filter have to be replaced. Note: The HEPA filter and the activated carbon filter have a similar lifetime. The
Summary of the content on the page No. 18
18 English Replacing the filters Tip: Place the appliance against a wall for more stability when you remove or insert filters. 1 Switch off the a ppliance and unp lug it. 2 Place y our fingers in the r ecesses o f the side panels and gentl y pull the top par t of the fr ont panel to war ds y ou. Then lift the hooks at the bottom of the panel out of the bottom of the a ppliance . 3 T o r emo v e filter 1 (pr e-filter), grab the tw o pr ojections and pull the filter to war ds y o
Summary of the content on the page No. 19
English 19 8 Put filter 4 (HEP A filter) back into the a ppliance . Note: Make sure that the side with the tag is pointing towards you. 9 Put filter 3 (activated carbon filt er) back into the a ppliance . 10 Put filter 2 (f ormaldeh yde filter f or A C4074 or m ulti-car e filter f or A C4072) back into the a ppliance . Note: Make sure that the side with the tag is pointing towards you. 11 Put filter 1 (pr e-filter) back into the a ppliance . Note: Make sure that the side with t
Summary of the content on the page No. 20
20 English 14 Pr ess the filter r eset button with a thin tool. Note: You do not need to press the filter reset button after cleaning filter 1 (pre-filter). Note: You cannot reset the appliance when you replace a filter before its filter replacement light starts flashing. Note: You cannot reset the appliance if it is not plugged in and switched on. storage 1 T o st or e the mains cor d, wind it r ound the cor d storage facility at the bottom of the a ppliance . Accessories New fi
