Summary of the content on the page No. 1
PORTABLE
COMPACT DISC PLAYER
WITH ANTI-SHOCK 10SEC.
INSTRUCTION MANUAL
PLEASE READ CAREFULLY BEFORE USING YOUR UNIT
MODEL: JX-CD477
OPEN
Summary of the content on the page No. 2
PROGRAM LOCATION OF CONTROLS PLAY/PAUSE ANTI-SKIP (power on) CD MODE LCD DISPLAY CD SKIP STOP BUTTON (power off) (NOT INCLUDED) DC IN 4.5V ADAPTOR JACK LINE OUT JACK PHONES JACK RECHARGE INDICATOR VOLUME CONTROL BASS BOOST DOOR OPEN HOLD RECHARGE CONTROL OPERATION AND FUNCTION POWER SUPPLY Your CD player requires 2 size “AA” alkaline batteries (not included), or use the AC adaptor 4.5V 600mA (not included) AC ADAPTOR OPERATION Plug one end of the AC adaptor into the DC 4.5V jack, BATTERY
Summary of the content on the page No. 3
3. Slide the charge switch to ON position to start charging. The charge indicator will light up. USE ONLY THE AC ADAPTOR FOR CHARGING. 4. After 15 hours, please unplug the AC adaptor and slide the recharge switch to OFF position. DO NOT CHARGE CONTINUOUSLY FOR 24 HOURS OR MORE. DOING SO CAN CAUSE THE PERFORMANCE OF THE RECHARGEABLE BATTERIES TO DETERIORATE. NOTE: You may play DISC’S whilst charging the batteries. If the operating time decreases drastically even when the rechargeable nickel-cadmi
Summary of the content on the page No. 4
3. Hold the disc with the label side up and press it onto the spindle until it “clicks” into place. 4. Close the disc compartment, press PLAY/PAUSE button, the disc will begin to spin, the display will indicate “01”, play will begin immediately from track number 1. 5. Adjust the volume as desired. 6. Set the BASS BOOST function as desired. 7. To stop play temporarily, press the PLAY/PAUSE button. • The track number flashes in the display. • Press the PLAY/PAUSE button again to resume. 8. To stop
Summary of the content on the page No. 5
1. Press the PROGRAM button in the STOP MODE. The “PROG” appears in the display. 2. Press the skip button ( ) to select the first track to be programmed. 3. Press the PROGRAM button again to enter the track into the memory. 4. Repeat steps 2 to 3 to program other track till you finish. 5. After programming is finished, press the PLAY/PAUSE Button. “PROG” shows steady in the display and programmed play begins. 6. The player stops automatically after all programmed tracks have been played. To play
Summary of the content on the page No. 6
LINE OUT THE ANTI-SKIP MEMORY FUNCTION (10SEC.) The digital anti-skip function uses semiconductor memory to prevent the sound from skipping when the unit is subjected to shocks and vibration during play. 1. When the ASP button is pressed during play, the indicator appears in the ANTI-S display and the digital anti-skip function turns on. The digital data equivalent to approximately 3 seconds (10 seconds) of music is stored in a read-ahead memory buffer before it is decoded and played. The displ
Summary of the content on the page No. 7
CLEANING THE CABINET Wipe with a soft cloth. If the cabinet is very dirty, dampen (not dripping wet) the cloth with a weak solution of soap water, and then wipe clean. HANDLING COMPACT DISCS 1. This unit is designed to play compact discs bearing the identifica- COMPACT tion logo to the right. Discs that do not carry this logo may not conform to the CD standard and may not play properly. DIGITAL AUDIO 2. Dirty, scratched or warped discs may cause skipping or noise. Pay attention to the following:
Summary of the content on the page No. 8
TROUBLE SHOOTING GUIDE SYMPTOM CAUSE SOLUTION Dead or weak batteries. Replace both batteries. CD Player will not The AC adaptor not Check the AC adaptor connection at AC turn on. connected properly. outlet and side of set. Disc inserted incorrectly Re-insert disc with label side facing up. Defective or wrong type Try another audio compact disc. compact disc. Close lid securely (push down left corner Disc will not play. CD door not closed. of door) Take out the CD and leave the CD door Moisture h
