Summary of the content on the page No. 1
Installation Guide
AQ339-Underwater Speaker
Table of Contents
Important Product Information 2
Warranty 3
Product Features 4
Installation Overview Diagrams 5
Detailed Speaker Images 6
Detailed In-Wall Mounting Hardware Images 7
CAUTION: THIS SPEAKER CONTAINS
In-Wall Installation Instructions 8
AN EXTREMELY POWERFUL MAGNET.
Drop-In Installation Instructions 10
DO NOT PLACE IN CLOSE PROXIMITY
TO TUBE TV MONITORS, TUBE VIDEO
Troubleshooting/Contact Information 11
MONITORS, AND MAGNETIC MEDIA.
Summary of the content on the page No. 2
IMPORTANT PRODUCT INFORMATION ! 1. DO NOT DROP SPEAKER- The speaker can be damaged both internally and externally if dropped. Damage caused by dropping the speaker is not covered under the warranty. 2. DO NOT EXPOSE SPEAKER TO HIGH DISTORTION LEVELS- Exposing the speaker to high levels of distortion may damage the speaker. This type of damage is not covered under the warranty. If the speaker stops playing, it is likely that the built-in protection circuit has activated. In the event this happ
Summary of the content on the page No. 3
WARRANTY United States Warranty and Return Policy AQ339-AQUASONIC POOL SPEAKER WARRANTY Clark Synthesis, Inc. warranties the AQ339-Aquasonic Pool Speaker to be free from defects and workmanship under normal use for a period of one (1) year from date of original purchase. For industrial or commercial use, the warranty period is six (6) months. Should warranty service be necessary, Clark Synthesis, Inc. will (at its discretion) repair or replace the defective merchandise with equivalent merchand
Summary of the content on the page No. 4
PRODUCT OVERVIEW The AQ339 Speaker is perfect for: • Swimming Pools • Lap Pools • Resorts and Hotels • Synchronized Swimming • Swim Team Training • Marine Animal Training PRODUCT FEATURES: The Aquasonic AQ339 is the only full-frequency, full-fidelity underwater swimming pool speaker in the world. The AQ339 works in both fresh and salt water pools and can either be permanently mounted in a large (standard) light niche or used as a drop-in speaker (see figures 1 and 2 on the following page). Th
Summary of the content on the page No. 5
PRODUCT OVERVIEW Figure 1. Side view of in-wall installation. Junction Box Pool Deck Wall of Pool Conduit Speaker in Niche Light Niche Figure 2. Side view of drop-in installation. Junction Box to Sturdy Object Audio System to Attach Rope Speaker Wire Pool Deck Rope Speaker Wall of Pool www.clarksynthesis.com Underwater Speaker 5
Summary of the content on the page No. 6
PRODUCT OVERVIEW The AQ339 Underwater Speaker Acoustic Sound Lens Threaded Stud, Brass Mounting Nuts, Jam Nuts Speaker Strain Relief Speaker Wire Rope Hole www.clarksynthesis.com 6 Underwater Speaker
Summary of the content on the page No. 7
PRODUCT OVERVIEW In-Wall Mounting Hardware (Purchased Separately) Face Ring Mounting Gasket Back View Face View Bolt & Rubber Washer Clamp Tabs Lock Tab Wire Clamp Large Light Niche Threaded Receiving Hole Lock Tab Receiving Plate www.clarksynthesis.com Underwater Speaker 7
Summary of the content on the page No. 8
IN-WALL INSTALLATION Carefully remove the speaker from its box. Install the mounting gasket around the rubber ring of 1 the sound lens (as shown below). Insure the mounting gasket is installed evenly and is firmly seated against the entire circumference of the sound lens. Place the speaker on a non-abrasive surface with the sound lens facing up. Hold the face ring above the 2 sound lens, allowing the clamp tabs to fall open. Set the face ring against the mounting gasket, insuring each clamp
Summary of the content on the page No. 9
IN-WALL INSTALLATION Use a wrench and a Phillips screwdriver to tighten the wire clamp. When fully tightened, the wire clamp 4 should be firmly seated in each clamp tab and the speaker should be secure. Pick up the assembly and insure it is still properly centered in the face ring. If not, loosen the wire clamp and adjust. Take the end of the speaker wire and pull it through the conduit hole in the back of the niche using 5 a wire puller. Leave 10 to 12 ft. of speaker wire in the niche to all
Summary of the content on the page No. 10
DROP-IN INSTALLATION Purchase a length of rope (1/8” to 1/4” outside diameter) that will allow you to place the speaker in 1 the area of the pool where you would like sound (see General Information section at the beginning of this manual for precautions when using this type of application). Carefully remove the speaker from its box. Locate the open hole on the speaker’s rubber ring (next to the interlaced speaker wire). Thread the rope through the hole. Tie a knot that will not come undone o
Summary of the content on the page No. 11
TROUBLESHOOTING The speaker is buzzing: • In-wall installation: Insure the lock tab is properly inserted behind the lock tab receiving plate. • Drop-in use: Insure the speaker is not vibrating against the pool wall. The speaker stopped working: • If the speaker stops playing, it is likely that the built-in protection circuit has activated. In the event this happens, turn the amplifier off for approximately 60 seconds to allow the circuit to reset. Turn down the volume on the stereo system and
Summary of the content on the page No. 12
11/2007 Ver. 1 ©2007 Clark Synthesis, Inc. www.clarksynthesis.com
