Apple Xserve 073-0668 user manual

User manual for the device Apple Xserve 073-0668

Device: Apple Xserve 073-0668
Size: 0,10 MB
Date of adding : 2013-09-12 12:11:21
Number of pages: 6
Print the manual


How to use this site?

Our goal is to provide you with a quick access to the content of the user manual for Apple Xserve 073-0668. Using the online preview, you can quickly view the contents and go to the page where you will find the solution to your problem with Apple Xserve 073-0668.

For your convenience

If looking through the Apple Xserve 073-0668 user manual directly on this website is not convenient for you, there are two possible solutions:

  • Full Screen Viewing - to easily view the user manual (without downloading it to your computer), you can use full-screen viewing mode. To start viewing the user manualApple Xserve 073-0668 on full screen, use the buttonFullscreen.
  • Downloading to your computer - You can also download the user manual Apple Xserve 073-0668 to your computer and keep it in your files. However, if you do not want to take up too much of your disk space, you can always download it in the future from ManualsBase.
Apple Xserve 073-0668 user manual
« Page 1 of 6 »
Print version

Many people prefer to read the documents not on the screen, but in the printed version. The option to print the manual has also been provided, and you can use it by clicking the link above - Print the manual. You do not have to print the entire manual Apple Xserve 073-0668 but the selected pages only. paper.


Below you will find previews of the content of the user manuals presented on the following pages to Apple Xserve 073-0668. If you want to quickly view the content of pages found on the following pages of the manual, you can use them.

Abstracts of contents
Summary of the content on the page No. 1

 Xserve
Power Supply
Replacement Instructions
Follow the instructions in this sheet carefully. Failure to follow these instructions could
damage your equipment and void its warranty.
Note: Online instructions covering customer-installable parts are available at
Tools Required
No tools are required for this procedure. You may, however, find a Phillips screwdriver
useful in releasing the thumbscrews at the front of the server.
Opening t

Summary of the content on the page No. 2

4. If the hard drives are in the locked position (the yellow security LED on the front panel is on), use the Allen key that came with the server to unlock them. 5. If the cable management arm is not in use, unplug all external cables except the power cord. 6. Touch the server’s metal case to discharge any static electricity. Important: Always ground yourself by touching the server’s case before you touch any parts or install any components inside the server. To avoid static electrici

Summary of the content on the page No. 3

9. Grasp the thumbscrews and slide the bottom housing forward part way to expose the two chassis levers. (Figure 2) 10. While depressing both levers, pull the bottom housing all the way forward and remove it from the rack. Figure 2 11. Place the bottom housing on a sturdy, flat surface and ESD mat. 12. Put on the ESD wrist strap. Xserve Power Supply - 3

Summary of the content on the page No. 4

Removing the Installed Power Supply Warning: The power supply is a high-voltage component and should not be opened for any reason, even when the server is off. Note: There are two versions of Xserve. If your version does not include a plastic duct over the heatsink, skip to step 3. 1. Release the latch on the heatsink duct from its slot, slide the cover away from the blower, and lift the end of the duct as shown. (Figure 3) 2. Remove the duct from the server. Figure 3 Xserve Power

Summary of the content on the page No. 5

3. Release the locking latch on the power supply cable connector and disconnect the cable from the drive interconnect board. (Figure 4) 4. Release the thumbscrew that secures the power supply to the chassis. Note: The thumbscrew is captive; you cannot remove it. 5. Grasp the metal flange of the power supply’s connector (on the left side) and lift up to disconnect the power supply from the logic board. Note: You may need to loosen the left side of the power supply and then lift at

Summary of the content on the page No. 6

Closing the Server 1. Carefully slide the bottom housing back into the rack. 2. Tighten the front thumb screws to secure it. Warning: Never turn on the server unless all of its internal and external parts are in place and it is closed. Operating the server when it is open or missing parts can damage it or cause injury.  Apple Computer, Inc. © 2003 Apple Computer, Inc. All rights reserved. This document is protected under U.S. Copyright Law and International Treaties, and no part of

Similar user manuals
# User manual Category Download
1 Apple 073-0625 Power Supply 13
2 Apple 073-0723 Power Supply 11
3 Apple USB Power Adapter Power Supply 11