Summary of the content on the page No. 1
WA01040XA
ENG_200501
Users Manual CX2
Summary of the content on the page No. 2
Users Manual SX2 Contents 1, Introduction ............................................................................................1-1 Safety Instructions........................................................................................1-3 2, PRICOM C-6400W...................................................................................2-1 Emission Notice ...........................................................................................2-2 Environment ........................
Summary of the content on the page No. 3
Users Manual SX2 4, Scanner Server .......................................................................................4-1 Initial set up ..................................................................................................4-2 Connect the PRICOM C-6400W and USB scanner..................................4-2 Use the Scanner Server ...............................................................................4-3 Install the PRICOM USB Utility.........................................
Summary of the content on the page No. 4
Users Manual SX2 6, Q&A .........................................................................................................6-1 The main menu does not start after Inserting the CD-ROM .....................6-1 The PRICOM C-6400W is not found in the configuration utility................6-1 I cannot print. ............................................................................................6-2 Occasionally I cannot print ..................................................................
Summary of the content on the page No. 5
Users Manual CX2 1, Introduction Thank you for purchasing this product. This manual provides information on how to configure and use the PRICOM C-6400W. Make sure to read all safety instructions carefully and fully understand them before starting to use the PRICOM C-6400W. The PRICOM C-6400W is a mini Print/Scanner/Storage wireless server. It allows sharing a printer, scanner and storage across a network. The PRICOM C-6400W will also support the status monitor in the Canon printer driver. Thi
Summary of the content on the page No. 6
Users Manual CX2 [About this Manual] - Copying all or part of this manual without our permission is forbidden. - The contents of this manual may be changed without advance notice. - If you have any question about this manual or our products, please contact our customer support. - This manual has been edited very carefully. However, silex technology, Inc. is not responsible for any mistakes included in this manual or any damages, direct or indirect, arising from the use of this manual. - Copyrigh
Summary of the content on the page No. 7
Users Manual CX2 Safety Instructions To ensure safe and proper use, please read the following information carefully before starting to use our product. The safety instructions include important information on the safe handling of the product and on general safety issues for the user. [Expression Meaning] "Danger" indicates the existence of a hazard that could result in death Danger or serious bodily injury if the safety instruction is not observed. "Warning" indicates the existence of a hazard t
Summary of the content on the page No. 8
Users Manual CX2 Danger Warnings about physical connections - Do not allow a power surge into this product. This could cause fire or an electric shock. If this product receives a power surge, unplug the AC adapter and contact us. - Keep the cables away from children. They may be injured or receive a shock. - If this product is detached from the printer, unplug the power to the printer before reconnecting. - If the printer has a ground wire, it must be used to prevent electrocution and power s
Summary of the content on the page No. 9
Users Manual CX2 Danger The following are warnings to be observed during use. - Do not remove the cover of this product. - Do not use this product with the cover removed. You may receive an electric shock. - Do not attempt to check, adjust or repair this product by yourself. You may receive an electric shock. Check with your dealer if the product needs to be repaired. - If this product becomes hot, or you smell smoke, turn off the printer then unplug the power cable and disconnect this device i
Summary of the content on the page No. 10
Users Manual CX2 Warning Notice about physical installation. - Do not use this product with the cover removed. You may receive an electric shock.When unplugging this product do not pull on the cord. The cord may break resulting fire and/or electric shock. Pull on the plug only. - Do not put this product on an unstable location. The product may fall causing injury or damage the product. - Do not put this product in a humid or dusty place. Fire or electric shock may occur. - When moving this pro
Summary of the content on the page No. 11
Users Manual CX2 Warning Observe the following instructions while using this product. - When the product will not be used for an extended time, disconnect and unplug the power cable. - Verify all cables are connected properly before using this product. 1-7 Introduction
Summary of the content on the page No. 12
Users Manual CX2 2, PRICOM C-6400W The PRICOM C-6400W is mini wireless print server/scanner server/storage server with a USB connection for Canon. This product supports Canon bubble jet printer, CAPT monochrome/color laser printer and MFP. You can monitor the print job status, printer status in Canon printer driver status monitor. - For the latest compatibility information, refer to our web page (http://www.silex.jp/) or contact customer support. When used correctly, the PRICOM C-6400W should no
Summary of the content on the page No. 13
Users Manual CX2 Emission Notice PRICOM C-6400W This equipment has been tested and found to comply with the limits for a Class B digital device, pursuant to Part 15 of the FCC Rules. These limits are designed to provide reasonable protection against harmful interference in a residential installation. This equipment generates, uses, and can radiate radio frequency energy and, if not installed and used in accordance with the instructions, may cause harmful interference to radio communications. H
Summary of the content on the page No. 14
Users Manual CX2 Environment The following are needed for the PRICOM C-6400W. The followings are objects that connect to the network. - PC with wireless communication - USB Cable (A-B Type Connectors) - Printer Supported OS Windows 98/Me, Windows 2000, Windows XP Operating Environment - Temperature : +10°C to +35°C - Humidity : 20% to 80%RH (no dewing) Storage Environment - Temperature : -10°C to +50°C - Humidity : 20% to 90%RH (no dewing) Electric current 5V +- 5% 1.0A EMI VCCI Class-B
Summary of the content on the page No. 15
Users Manual CX2 Equipment explanation Part name and function Bottom Top Ethernet Address Infra LED Status LED Link LED (The last 6 digits are the product serial (Green) (Orange) (Green) number) Front Side Right Side Power Connector USB Port Push Switch The LED’s have the following meaning: Status LED (Orange) Flashes during data transfer. Link LED (Green) Lights when an OldAdHoc mode network connection is established. Lights when an AdHoc mode network connection is establishe
Summary of the content on the page No. 16
Users Manual CX2 USB Port Connect a USB Cable (A Type connector) Power Connector Connect AC adapter Push Switch The push switch is used to restore Factory Defaults and change to Infrastructure mode. The PRICOM C-6400W is initialized. 1. Make sure that PRICOM C-6400W is not connected to the AC adapter. 2. While pushing the push switch of the PRICOM C-6400W, connect the AC Adapter. 3. Hold the push switch for 15 seconds. Only if Link LED is on, let go of the push switch.
Summary of the content on the page No. 17
Users Manual CX2 Start in Infrastructure mode - It is possible to put the PRICOM C-6400W into Infrastructure mode and connect to an access point if the access point does not use WEP. 1. With the PRICOM C-6400W set to factory default, verify the Link LED is on after the connecting the AC adapter to the PRICOM. 2. After holding the push switch for 15 seconds, release the switch. 3. After a few seconds, all of the LED’s will light and then go out immediately. 4. After a few seconds, the Infra. LED
Summary of the content on the page No. 18
Users Manual CX2 How to Connect Connect the PRICOM C-6400W to Printer and Network - If the PRICOM C-6400W has been used in another network environment, restore to factory default. - The PRICOM C-6400W cannot connect to a USB hub. The PRICOM C-6400W needs the following to connect to a network. USB Cable A-B Type 1. Connect the AC Adapter to the PRICOM C-6400W. 2. Plug in the Power cable to the printer/ Canon MFP. 3. Connect the PRICOM C-6400W to a printer/Canon MFP. The PRICOM uses a type A conn
Summary of the content on the page No. 19
Users Manual CX2 4. Make sure that printer is working and turned on. - Using an AC adapter other than the one provided with the PRICOM C-6400W can cause damage. - Connect only to a printer/Canon MFP. - Wait for 2 or more seconds after connecting/disconnecting the USB cable. - Do not disconnect the USB cable during printing, scanning or reading/writing from a memory card. - After turning on the PRICOM C-6400W or connecting the USB cable, printing will proceed according to priority. PRICOM C-6400W
Summary of the content on the page No. 20
Users Manual CX2 Other Functions The other functions of the PRICOM C-6400W are shown below. Function Assign the IP address automatically using DHCP, BOOTP and RARP - DHCP/BOOTP If a DHCP/BOOTP server is working on your network, the DHCP/BOOTP protocol of the PRICOM C-6400W will assign the IP address to the PRICOM C-6400W. - The PRICOM’s DHCP protocol is compatible with RFC2131/2132. - If you use the DHCP function of the PRICOM C-6400W, talk to your administrator. - RARP If a RARP server is wor
