Summary of the content on the page No. 1
OWNER'S MANUAL
Projection Television
®
Owner's Record
The model number and serial number are on the back
43H71
of your TV. Record these numbers in the spaces below.
Refer to these numbers whenever you communicate
with your Toshiba dealer about this TV.
53H71
Model number:
Serial number:
61H71
© 2001 TOSHIBA CORPORATION
All Rights Reserved
Index Appendix Using the TV’s Setting up Using the Connecting Introduction
Features your TV Remote Control your TV
Summary of the content on the page No. 2
Important Information Note to CATV system installers in the USA WARNING This reminder is provided to call the CATV system installer’s TO REDUCE THE RISK OF FIRE OR ELECTRIC SHOCK, DO attention to Article 820-40 of the NEC, which provides NOT EXPOSE THIS APPLIANCE TO RAIN OR MOISTURE. guidelines for proper grounding, and, in particular, specifies that the cable ground shall be connected to the grounding system of the building, as close to the point of cable entry as practical. Precautions Install
Summary of the content on the page No. 3
Using the strobe function ............................................... 29 Introduction................................................................ 4 Using the LOCKS menu ............................................... 30 Welcome to Toshiba ......................................................... 4 Entering the PIN code ............................................ 30 Exploring your new TV ................................................... 4 Changing the PIN code .........................
Summary of the content on the page No. 4
PIC SIZE STROBE Introduction Welcome to Toshiba Congratulations! You have purchased one of the finest projection TVs Please Note on the market. The goal of this manual is to guide you through setting up and operating your Toshiba TV as quickly as possible. On some models, the SET UP menu automatically appears on- This manual applies to models 43H71, 53H71, and 61H71. Before screen the first time the TV is you start reading, check the model number by looking at the rear of turned on. the TV. To c
Summary of the content on the page No. 5
Connecting your TV ANTENNA Coaxial Cable If you have not connected electronic equipment before, or you have been frustrated in the past, you may wish to read this section. (Cables AUDIO are not supplied.) Cables • A coaxial cable is the standard cable that comes in from your antenna or cable converter box. Coaxial cables use “F” VIDEO Cable connectors. • Audio and video cables are usually color-coded according to use: yellow for video and red and white for audio. The red audio cable S-VIDEO Cabl
Summary of the content on the page No. 6
Connecting a cable converter box This connection allows you to watch basic and premium cable Note: channels. When you use a converter box with your TV, the remote control will not operate some To use the TV’s features, select ANT-1. To view premium channels, features, such as programming your favorite select ANT-2, tune the TV to channel 3 or 4 (whichever channel is channels, labeling channels, and locking vacant in your area), and use the converter box to change channels. channels. You will nee
Summary of the content on the page No. 7
Connecting a DVD player or satellite receiver and a VCR This connection allows you to watch DVD/satellite, VCR, and TV Note: programs, and record one TV channel while watching another For the highest possible picture quality from a non-ColorStream DVD player/satellite channel. receiver, use an S-video cable between the You will need: TV and DVD player/satellite receiver. (If your • one coaxial cable DVD player or satellite receiver is ColorStream-compatible, see page 8). • two pairs of audio cab
Summary of the content on the page No. 8
Connecting a DVD player with component video and a VCR Note: This connection allows you to watch DVD, VCR, and TV programs, and record DVD and TV programs. You can record from one source For the highest possible picture quality, use ColorStream (component video) cables while watching a program from another source. between the TV and DVD player. You can Your TV has ColorStream (component video) inputs. Connecting connect the ColorStream cables from the your TV to a component video-compatible DVD
Summary of the content on the page No. 9
Connecting a DTV receiver/set-top box with component video and a VCR Note: This connection allows you to watch DTV (digital TV broadcast), VCR, and TV programs, and record DTV and TV programs. You can For the highest possible picture quality, use ColorStream (component video) cables record from one source while watching a program from another between the TV and DTV receiver. You can source. connect the ColorStream cables from the Your TV has ColorStream (component video) inputs. Connecting DTV r
Summary of the content on the page No. 10
Connecting two VCRs This connection allows you to record (dub/edit) from one VCR to another VCR while watching a videotape. You can also record from one TV channel while watching another TV channel. You will need: • one coaxial cable Caution: The unauthorized recording of television • two pairs of audio cables (two single audio cables for mono programs, videotapes, and other materials VCRs) may infringe upon the provisions of copyright • two video cables (two S-video cables for S-VHS VCRs) laws.
Summary of the content on the page No. 11
Connecting an audio system Amplifier This connection allows you to use an audio amplifier to adjust the LINE IN LR audio level. This also allows you to use external speakers. To control the audio, turn on the TV and the stereo amplifier, and TV turn off the built-in speakers (see “Turning off the built-in speakers” on page 45). AUDIO CENTER CHANNEL IN ANT( 75 ) You will need: ANT-1 ON OFF • one pair of audio cables OUT OUT S-VIDEO VAR RL AUDIO Note: VIDEO VIDEO Y Y ANT-2 To hear sound when us
Summary of the content on the page No. 12
PIC SIZE STROBE Using the remote control Note: Preparing the remote control for use The TV remote control may not operate The remote control can operate the TV, most VCRs, and most cable certain features on your VCR, cable TV TV converters together, even if they are different brands. If you will be converter, or other electronic device. using your TV with a Toshiba VCR or cable TV converter, your Refer to the owner’s manuals for your other remote control is already programmed and ready to use. I
Summary of the content on the page No. 13
PIC SIZE STROBE Programming the remote control for use with a non-Toshiba VCR or cable TV converter RECALL LIGHT RECALL POWER The TV remote control is pre-programmed to operate Toshiba VCRs POWER TV and cable TV converters. CABLE MUTE TV/VIDEO TIMER VCR To program the TV remote control to operate non-Toshiba VCRs or cable converters: 12 3 CH Channel yz 1. Refer to the “VCR code table” or “Cable TV converter code 45 6 table” on pages 14–15 to find the corresponding code for your Channel 78 9 VCR
Summary of the content on the page No. 14
VCR code table Brand name Code number Adventura 019 Jensen 060 Quasar 054,096 Aiko 297 JVC 027,060,086 Radio Shack 019,056,344 Aiwa 019 Kenwood 057,060,086 Radix 056 Akai 060,068,080,125, KLH 091 Randex 056 261 Kodak 054,056 RCA 061,079,084,096, American High 054 Lloyd 019 124,125,168,221 Asha 259 Lloyd’s 227 Realistic 019,054,056,065, Audiovox 056 Logik 091 066,067,081,085, Beaumark 259 LXI 056 123,259 Bell & Howell 123 Magnavox 054,058,100,129, Ricoh 053 Brandt 206 168 Runco 058 Broksonic 140,
Summary of the content on the page No. 15
Cable TV converter code table Brand name Code number ABC 020,022,026,027, Samsung 059,163 030,032,033,036, Scientific Atlanta 025,027,036,296 066 Signal 034,059 Antronix 041 Signature 030 Archer 041,058,172 SL Marx 059 Belcor 075 Sprucer 040 Cable Star 075 Standard Cabletenna 041 Components 174 Cableview 041 Starcom 022,034,066 Century 172 Stargate 034,059 Citizen 172 Starquest 034 Colour Voice 044,050 Sylvania 020 Comtronics 059,079 Teleview 059 Contec 038 Texscan 020 Dae Ryung 027 Tocom 031,03
Summary of the content on the page No. 16
PIC SIZE STROBE Learning about the remote control POWER turns the TV on and off RECALL displays information on-screen (page 46) LIGHT RECALL POWER LIGHT illuminates the keypad for five seconds TV CABLE TIMER sets the TV to turn off at a specific time (page 41) MUTE TV/VIDEO TIMER VCR TV/VIDEO selects the video input source (page 39) MUTE turns off the sound (page 42) 12 3 CH TV/CABLE/VCR s witches between TV, Cable and VCR (pages 12-13) 45 6 Channel y z cycles through programmed channels (
Summary of the content on the page No. 17
PIC SIZE STROBE Setting up your TV 43H71 CH Learning about the menu system PO VOL VOL MENU EXIT TV/VIDEO TOUCH FOCUS After you have installed the batteries and programmed the remote CH control, you will need to set some preferences on the TV using the menu system. You can access the menus using the buttons on the TV MENU yzx • EXIT or remote control. 1. Press MENU to open the menu system. 2. Press x or • to select a menu. 53H71/61H71 3. Press y or z select an item. CH MENU EXIT TV/VIDEO TOUCH FO
Summary of the content on the page No. 18
PIC SIZE STROBE Changing the on-screen display language 43H71 CH Choose from three different languages (English, French, and Spanish) PO MENU VOL VOL EXIT TV/VIDEO TOUCH FOCUS for the on-screen display of adjustment menus and messages. CH To select a language: 1. Press MENU, and then press x or • until the SET UP menu appears. MENU yzx • 2. Press y or z to highlight LANGUAGE. 1 2 3 4 5 6 7 8 9 10 11 12 13 14 15 16 17 18 19 20 21 22 23 24 25 26 27 28 29 30 31 32 33 34 35 1 1 53H71/61H71 2 2 3 3 4
Summary of the content on the page No. 19
PIC SIZE STROBE Adding channels to the TV’s memory Note: When you press Channel yz, the TV will select only the channels stored in the TV’s channel memory. To tune the TV to a channel not programmed in the channel memory, use the Channel Follow the steps below and on the next page to program all active Number buttons on the remote control. channels into the TV’s memory. Programming channels automatically The TV can automatically detect all active channels in your area and store them in its memor
Summary of the content on the page No. 20
PIC SIZE STROBE Adding and erasing channels manually 43H71 After you have programmed the channels automatically, you can CH PO MENU VOL VOL EXIT TV/VIDEO TOUCH FOCUS manually add or erase specific channels. CH To add or erase channels: 1. Select the channel you want to add or erase. If you are adding a channel, you must select the channel using the Channel Number MENU yzx • buttons. Channel yz 2. Press MENU, and then press x or • until the SET UP menu appears. 53H71/61H71 3. Press y or z to high
