Summary of the content on the page No. 1
CONTENTS
Usage Notice .....................................................................................2
Safety Instructions ................................................................................................................. 2
Introduction .......................................................................................5
Projector Features ................................................................................................................. 5
Package Contents .
Summary of the content on the page No. 2
Usage Notice Safety Instructions Read all of these instructions before you operate your projector and save for future reference. 1. Read instructions All the safety and operating instructions should be read before the appliance is operated. 2. Notes and warnings All notes and warnings in the operating instructions should be adhered to. 3. Cleaning Unplug the projector from the wall socket before cleaning. Use a damp cloth for cleaning the projector housing. Do not use liquid or aerosol clean
Summary of the content on the page No. 3
8. Replacement parts When replacement parts are required, be sure that the replacement parts are specified by the manufacture. Unauthorized substitutions may result in fire, electric shock or other hazards. 9. Moisture Condensation Never operate this projector immediately after moving it from a cold location to a warm one. When the projector is exposed to such a change in temperature, moisture may condense on the lens and the crucial internal parts. To prevent the unit from possible damage,
Summary of the content on the page No. 4
Notes on the AC Power Cord AC Power Cord must meet the requirement of countries where you use this projector. Please confirm your AC plug type with the graphics below and ensure that the proper AC Power Cord is used. If the supplied AC Power Cord does not match your AC outlet, please contact your sales dealer. This projector is equipped with a grounding type AC line plug. Please ensure that your outlet fits the plug. Do not defeat the safety purpose of this grounding type plug. We highly recomme
Summary of the content on the page No. 5
Introduction Projector Features The projector integrates high-performance optical engine projection and a user - friendly design to deliver high reliability and ease of use. The projector offers the following features: ® Single chip 0.55" Texas Instruments DLP technology SVGA (800 x 600 pixels) XGA (1024 x 768 pixels) ® Compatibility with Macintosh computers Compatibility with NTSC, PAL, SECAM and HDTV D-Sub 15-pin terminal for analog video connectivity User-friendly, multi-language on-s
Summary of the content on the page No. 6
Package Contents When you unpack the projector, make sure you have all these components: Projector AC Power Cord Remote Control (IR) & batteries (AAA *2 PCS) VGA Cable (D-SUB to D- Carry Bag (optional for Remote Control (IR) & batteries SUB) certain models) (AAA *2 PCS) for certain regions Documentation: User's Manual Warranty Card Quick Start Card WEEE Card (for EMEA only) Note For European warrant information please visit www.optomaeurope.com Due to the difference in applications for
Summary of the content on the page No. 7
Projector Overview Front View 8 7 9 6 4 5 1 2 3 1 Front IR remote control 6 Control panel sensor 2 Elevator foot 7 Zoom ring 3 Projection lens 8 Focus ring 4 Speaker 9 Lamp cover 5 Ventilation holes EN-7
Summary of the content on the page No. 8
Rear View 2 1 3 1 AC power socket 2 Connection ports (HDMI is only on certain models) 32 Kensington lock Bottom View 3 1 2 1 Security bar 22 Ceiling mount holes 3 Ventilation holes Note This projector can be used with a ceiling mount for support. The ceiling mount is not included in the package. Contact your dealer for information to mount the projector on a ceiling. EN-8
Summary of the content on the page No. 9
Using the Product Control Panel 4 6 2 3 5 1 7 8 4 1 Power Turn the projector on or off. 2 SOURCE Switch between input signals. 3 MENU/EXIT Display or exit the on-screen display menus. 4 Keystone ( / ) Manually correct distorted images resulting from an angled projection. 5 Four directional buttons Use four directional buttons to select items or make adjustments to your selection. 6 Re-SYNC Automatically synchronize the projector to the input source. 7 POWER (Power LED indicator) Refer to “LED
Summary of the content on the page No. 10
Connection Ports 2 4 1 3 5 6 10 9 8 7 1 AUDIO IN Connect an audio output from video equipment or computer to this jack. 2 HDMI (HDMI is only on certain models) Connect HDMI output from video equipment to this jack. 3 S-VIDEO Connect S-Video output from video equipment to this jack. 4 VGA1-IN/YPbPr Connect image input signal (analog RGB or component) to this jack. 5 RS-232 When operating the projector via a computer, connect this to the controlling computer's RS-232C port. 6 Service/Mouse This
Summary of the content on the page No. 11
Remote Control 1 Switch Switch to mouse mode when the on-screen menus are close. 1 12 2 Source 2 13 Switch between input signals. 3 3 Four directional buttons 14 Use four directional buttons to 15 4 select items or make adjustments to your selection. 5 16 4 Left mouse Perform the left button of the 17 6 mouse when mouse mode is 18 7 activated. 19 8 5 Keystone ( / ) 20 9 Manually correct distorted 21 10 images resulting from an 22 11 angled projection. 6 Brightness 10 Display the setting
Summary of the content on the page No. 12
14 Enter Using the remote mouse Confirmed selections. control 15 Right mouse The capability of operating your computer with the remote control gives you more Perform the right button of the flexibility when delivering presentations. mouse when mouse mode is 1. Connect the projector to your PC or activated. notebook with a USB cable prior to 16 Volume ( / ) using the remote control in place of Adjust the volume level. your computer’s mouse. See 17 Menu “Connecting a computer” on Display
Summary of the content on the page No. 13
Installing the Batteries 1. Open the battery cover in the direction shown. 2. Install batteries as indicated by the diagram inside the compartment. 3. Close the battery cover into position. Caution Risk of explosion if battery is replaced by an incorrect type. Dispose of used batteries according to the instructions. Make sure the plus and minus terminals are correctly aligned when loading a battery. Note Keep the batteries out of the reach of children. There is a danger of death by acci
Summary of the content on the page No. 14
Remote Control Operation Point the remote control at the infrared remote sensor and press a button. Operating the projector from the front Note The remote control may not operate when there is sunlight or other strong light such as a fluorescent lamp shining on the remote sensor. Operate the remote control from a position where the remote sensor is visible. Do not drop the remote control or jolt it. Keep the remote control out of locations with excessively high temperature or humidity. Do
Summary of the content on the page No. 15
Connection When connecting a signal source to the projector, be sure to: 1. Turn all equipment off before making any connections. 2. Use the correct signal cables for each source. 3. Ensure the cables are firmly inserted. 6 7 1 6 8 3 4 1 2 1 5 1. ............................................................................................*Audio cable 2. ............................................................................................*HDMI cable 3. ......................................
Summary of the content on the page No. 16
Connecting a computer or monitor Connecting a computer The projector provides two VGA input sockets that allow you to connect them ® ® to both IBM compatibles and Macintosh computers. A Mac adapter is needed if you are connecting legacy version Macintosh computers. To connect the projector to a notebook or desktop computer: 1. Take the supplied VGA cable and connect one end to the D-Sub output socket of the computer. 2. Connect the other end of the VGA cable to the VGA1-IN/YPbPr or VGA2-IN/Y
Summary of the content on the page No. 17
Connecting Video source devices You can connect your projector to various Video source devices that provide any one of the following output sockets: HDMI Component Video S-Video Video (composite) You need only connect the projector to a Video source device using just one of the above connecting methods, however each provides a different level of video quality. The method you choose will most likely depend upon the availability of matching terminals on both the projector and the Video sou
Summary of the content on the page No. 18
Connecting an HDMI source device Examine your Video source device to determine if it has a set of unused HDMI output jacks available: If so, you can continue with this procedure. If not, you will need to reassess which method you can use to connect to the device. To connect the projector to an HDMI source device: 1. Take an HDMI cable and connect one end to the HDMI output jack of the HDMI source device. 2. Connect the other end of the HDMI cable to the HDMI jack on the projector. Connecti
Summary of the content on the page No. 19
Connecting an S-Video source device Examine your Video source device to determine if it has an unused S-Video output socket available: If so, you can continue with this procedure. If not, you will need to reassess which method you can use to connect to the device. To connect the projector to an S-Video source device: 1. Take an S-Video cable and connect one end to the S-Video output socket of the Video source device. 2. Connect the other end of the S-Video cable to the S-VIDEO socket on the
Summary of the content on the page No. 20
Connecting a composite Video source device Examine your Video source device to determine if it has a set of unused composite Video output sockets available: If so, you can continue with this procedure. If not, you will need to reassess which method you can use to connect to the device. To connect the projector to a composite Video source device: 1. Take a Video cable and connect one end to the composite Video output socket of the Video source device. 2. Connect the other end of the Video ca
