Summary of the content on the page No. 1
Installation and Assembly Manual:
PRS, RTR Series Projector Mount
Models: PRS-UNV, PRS-UNV-S, PRS-UNV-W
PRS-UNVP, PRS-UNVP-S, PRS-UNVP-W
RTR-UNB, RTR-UNS, RTR-UNW
This product is intended for use with UL
Listed products and must be installed by a
qualified professional installer.
Maximum UL Load Capacity:
25 lb (11.34 kg)
ISSUED: 09-19-05 SHEET #: 055-9441-5 10-31-08
1 of 12
3215 W. North Ave. • Melrose Park, IL 60160 (800) 865-2112 or (708) 865-8870 Fax: (708) 865-2941 www.peer
Summary of the content on the page No. 2
Note: Read entire instruction sheet before you start installation and assembly. WARNING Do not begin to install your Peerless product until you have read and understood the instructions and warnings contained in this Installation Sheet. If you have any questions regarding any of the instructions or warnings, please call Peerless customer care at 1-800-865-2112. This product should only be installed by someone of good mechanical aptitude, has experience with basic building construction, and f
Summary of the content on the page No. 3
Before you start check the parts list to insure all of the parts shown are included. PRS-UNV, PRS-UNV-S, PRS-UNV-W, PRS-UNVP PRS-UNVP-S PRS-UNVP-W Parts List RTR-UNB RTR-UNS RTR-UNW Description Qty. Part # Part # Part # A projector mount assembly (non-security adjustments) 1 055-0607 055-0608 055-0609 projector mount assembly (security adjustments) 1 055-0604 055-0605 055-0606 B adapter plate 1 055-1879 055-4879 055-2879 C #14 x 2.5 phillips hex head wood screw 2 5S1-015-C03 5S1-015-C04 5S1-015-
Summary of the content on the page No. 4
Installation to Extension Column / Ceiling Plate NOTE: Refer to accompanying instructions with ceiling plates (sold separately) for installing these models to 1 ceiling. Screw projector mount assembly (A) onto extension column as shown in figure 1.1. NOTE: For 3/4" extension columns, reducer ACC 913 will be required as shown in figure 1.2. Tighten swivel stop screw against extension column, flush mount tube or reducer using 4 mm security t-wrench (L) as shown in figure 1.3. NOTE: Swivel stop scr
Summary of the content on the page No. 5
Installation To Wood Joist Ceilings WARNING Installer must verify that the supporting surface will safely support the combined load of the equipment and all attached hardware and components. Tighten wood screws so that projector mount assembly is firmly attached, but do not overtighten. Overtightening can damage the screws, greatly reducing their holding power. Never tighten in excess of 80 in. lb (9 N.M.). Make sure that mounting screws are anchored into the center of the stud. The us
Summary of the content on the page No. 6
Installation to Concrete Ceilings WARNING Concrete must be 2000 psi density minimum. Lighter density concrete may not hold concrete anchor. Make sure that the supporting surface will safely support the combined load of the equipment and all attached hard- ware and components. Place projector mount assembly (A) on ceiling as a 3 template and mark the center of the two mounting holes. Drill two 1/4" (6 mm) dia. holes to a minimum depth of 2.5" (64 mm). Attach projector mount assembly (A) using
Summary of the content on the page No. 7
Installation to Threaded Rod (Not evaluated by UL - Professional installation only) Thread two 3/8-16 hex thin nylon-insert locknuts (not included) on two 3/8-16 threaded rods (not included) to the 4 desired height of projector mount assembly. Attach projector mount assembly (A) to the two 3/8-16 threaded rods using two 3/8-16 hex thin nylon-insert locknuts as shown in figure 4.1 or figure 4.2. 3/8 -16 THREADED ROD (NOT INCLUDED) 3/8 -16 THREADED ROD (NOT INCLUDED) 3/8 -16 HEX THIN 3/8 -16 HEX
Summary of the content on the page No. 8
Attaching Adapter Plate to Projector Note: The projector you are installing may differ in appearance from the sample illustrated below. Place projector upside down. Locate adapter plate (B) with notch facing forward as close to projector center of 5 gravity as possible without covering any mounting holes. Loosen channels with 4 mm security t-wrench (L), and if there are only three mounting holes remove fourth channel. Using one channel for each mounting hole, position feet of channels over mount
Summary of the content on the page No. 9
Attaching Adapter Plate to Projector (continued) WARNING Always use an assistant or mechanical lifting equipment to safely lift and position the projector. Slide connection block with projector into projector mount assembly (A) as shown. Push in and tighten captive screw 7 to secure projector to projector mount assembly (A). FRONT OF MOUNT CONNECTION BLOCK A FRONT OF MOUNT CAPTIVE SCREW IMPORTANT: For security installations, insert one #10-32 x 1/4" socket pin screw (E) through projector mou
Summary of the content on the page No. 10
Projector Alignment To adjust yaw (swivel) for threaded rod mounting applications: Loosen locknuts on threaded rods (refer to step 9 four), until projector mount can be rotated. Rotate mount to desired position and retighten screws or locknuts. To adjust yaw (swivel) for extension column applications: Loosen screw on projector mount assembly (A) indicated below until projector mount can be rotated. Rotate mount to desired position and retighten screw. To adjust pitch (forward and backward ti
Summary of the content on the page No. 11
PRS Series Projector Mount Accessories ○○○○○○○○○○○○○○○○○○○○○○○○○○○○○○○○○○○○○○○○○○○○○ ○○○○○○○○○○○○○○○○○○○○○○○ Ceiling Plates ® Escutcheon Ring Truss Ceiling Adapter Unistrut Adapter MODEL: ACC 640 MODEL: ACC 557* MODEL: ACC 550 MAX LOAD: 250 lbs. (113.4 kg.) MAX LOAD: 250 lbs. (113.4 kg.) Covers hole where extension COLOR: Black COLOR: Black column passes through ceiling Hinged ring wraps around extension column Attaches to a square, round, Designed for use with Included with CMJ 500
Summary of the content on the page No. 12
PRS Series Projector Mount Accessories ○○○○○○○○○○○○○○○○○○○○○○○○○○○○○○○○○○○○○○○○○○○○○ ○○○○○○○○○○○○○○○○○○○○○○○ Cord Management Includes, four, 2' sections Cord Wrap Designed to externally route cords along the MODELS: ACC 852(W)(S)* outside of an 1/2" extension column Sections can be stacked to create longer lengths COLOR: Black, White, or Silver or cut to desired length ○○○○○○○○○○○○○○○○○○○○○○○○○○○○○○○○○○○○○○○○○○○○○ ○○○○○○○○○○○○○○○○○○○○○○○ Extension Columns Fixed Length 1 1/2" Adjustable Le
