Summary of the content on the page No. 1
E30GF74GPS E36GF75GPS E36GF76GPS 318201761
Summary of the content on the page No. 2
2 Finding Information READ AND SAVE THESE INSTRUCTIONS NO NOTE TE NO NO NOTE TE TE Installer: Leave instructions with owner. Owner: Read your range Use & Care guide. It contains important safety information for operating this appliance. It also has many suggestions for getting the best results from your appliance. Read all instructions before installing the range. For your safety, please read and observe all safety instructions. This guide will help you anticipate all installations connections.
Summary of the content on the page No. 3
3 Finding Information TABLE OF CONTENTS Please Read And Save This Guide .................... 2 Questions .......................................................... 2 Table Of Contents ............................................. 3 Safety ..................................................................... 4 Important Safety Instructions ............................... 4 Definitions ........................................................... 4 Safety Precautions ................................
Summary of the content on the page No. 4
Safety 4 IMPORTANT SAFETY INSTRUCTIONS
Summary of the content on the page No. 5
Safety 5 SAFETY PRECAUTIONS
Summary of the content on the page No. 6
6 Safety WARNING WARNING WARNING WARNING WARNING Never use this appliance as a space heater to heat or warm a room. Doing so may result in carbon monoxide poisoning and overheating of the oven.
Summary of the content on the page No. 7
7 Preparing for Installation VERIFY PACKAGE CONTENTS • Literature Pack • Griddle (some models) • Anti-Tip Bracket • Simmer Plate • Burner Grate Pack • Broiler Pan/Insert • Burner Rings • Stainless Steel Cleaner • LP Conversion Kit • Wok Ring • Burner Caps • Oven Racks GAS AND ELECTRIC REQUIREMENT TABLE NO NOTE TE NO NO NOTE TE TE This range is shipped from the factory pre-set for use with natural gas. For LP conversion see the
Summary of the content on the page No. 8
Preparing for Installation 8 ELECTRICAL POWER SUPPLY REQUIREMENTS It is the owner’s responsibility to ensure that the electrical connection of this appliance is performed by a qualified electrician. The electrical installation, including minimum supply wire size and grounding, must be in accordance with the National Electric Code ANSI/NFPA 70-1993* (or latest revision) and local codes and ordinances. In Canada, electrical grounding must be in accordance with the current CSA C22.1 Canadian Electr
Summary of the content on the page No. 9
Preparing for Installation 9 GAS AND ELECTRICAL ROUGH-IN Locations A manual shut valve must be installed in the gas piping, external to the appliance, for the purpose of turning on or shutting off gas to the appliance. Place the location of the range and the gas supply to allow access to the valve when the unit is installed. Access to the remote circuit breaker panel/fuse box, with the range in place, must also be allowed for in the installation. Any openings in the wall behind the appliance and
Summary of the content on the page No. 10
Preparing for Installation 10 CABINET AND COUNTERTOP PREPARATION Check your local building codes for the proper method of installation. In the absence of local codes, this appliance should be installed in accordance with the National Fuel Gas Code ANSI Z223.1/NFPA 54. In Canada, installation must conform to current Natural Gas Installation Code, CAN1-1.1-M and the local codes where applicable. This range has been design-certified according to ANSI Z21.1b, latest edition. Be certain that the app
Summary of the content on the page No. 11
Preparing for installation 11 GENERAL DIMENSIONS Plan the installation so that the electrical connection, gas shut-off valve, and pressure regulator are accessible from the front of the cabinet. Figure 2 Ventilation Hood 13" (330 mm) Max Top of Finished Vertical non- Counter combustible surface 30" (762 mm) Min 10" (254 mm) Min. 18" (457 mm) to combustible sides walls Min above the range (both sides) Recommended utility location 25" (635 mm) E30GF74GPS, E36GF75GPS, E36GF76GPS Cutout Dimensions
Summary of the content on the page No. 12
Preparing for Installation 12 GENERAL DIMENSIONS
Summary of the content on the page No. 13
Preparing for Installation 13 WOOD/COMPOSITE OVERLAY INSTALLATION The bottom of an overhead hood should be 30” minimum to 36” above the countertop. This would typically result in the bottom of the hood being 66” to 72” above the floor. These dimensions provide safe an efficient operation of the hood.
Summary of the content on the page No. 14
14 Installation INSTALLING THE ANTI-TIP BRACKET ** **Note: Increase or decrease this dimension as necessary for range top to be flush with countertop. FIG. 3
Summary of the content on the page No. 15
Installation 15 INSTALLING THE 36” RANGE OPTIONAL BACKGUARD MR Your Electrolux Icon range was shipped with a backguard in place. These instructions cover the installation of one of the optional backguards. Installing the Range Optional Backguard: WARNING WARNING WARNING WARNING WARNING Be sure the range is not connected to gas or power before proceeding. 1. Remove existing backguard by removing 4 screws on rear of backguard (2 screws per side). 2. Remove the backguard from its box. 3. To avoi
Summary of the content on the page No. 16
16 Installation REMOVING THE OVEN DOOR Open the door to its fully opened position. Rotate the catch over the retaining arm on each hinge. Lift the oven door to about a 30 degree angle from the horizontal position. Pull the door away from the oven while continuing to lift. WARNING WARNING WARNING WARNING WARNING Do not attempt to disengage the hinge catches with the door removed from the oven. The hinge springs could release causing personal injury. Do not lift or carry the oven door by the handl
Summary of the content on the page No. 17
17 Installation GROUNDING 1 The range is equipped with a three-prong power cord (grounding plug which mates with a standard three-prong grounding wall receptacle to minimize the possibility of electrical shock hazard from the range). 2 Where a standard two-prong wall receptacle is encountered, it is the responsibility and obligation of the customer to have it replaced with a properly grounded three- prong wall receptacle. Do not cut or remove the grounding prong from the power cord. CONNECT RA
Summary of the content on the page No. 18
Installation 18 CONNECT RANGE TO GAS SUPPLY WARNING WARNING WARNING WARNING WARNING • Do not apply excessive pressure when tightening gas connections and fittings. • Do not use teflon tape or plumber’s putty on gas flex line connections. • Turn all control valves to the “OFF” position. Turn on gas supply and check all lines and connections with leak detector, such as soap and water solution. Do not use flame to check for leaks. After verifying that there are no gas leaks, turn off the gas sup
Summary of the content on the page No. 19
Operation 19 VERIFYING THE OPERATION Before beginning the test procedure, ensure that all cooktop control valves are in the “OFF” position, and all burner rings, burner caps, and grates are properly positioned on the top frame. Turn on the gas supply at the shut-off valve. Turn on the power supply to the range. Select a temperature of 350°F by rotating the oven selector knob to “350”. Rotate knob to the “Off” position to stop the heating process. Test each top burner separately by pressing and
Summary of the content on the page No. 20
Operation 20 TO ENSURE PROPER AND SAFE OPERATION NO NO NOTE TE TE NO NOTE TE REFER TO THE USE AND CARE MANUAL FOR DETAILED INSTRUCTIONS. • Read all instructions before using this appliance. Install or locate the appliance only in accordance with the provided Installation Instructions. • Do not attempt to adjust, repair, service, or replace any part of your appliance unless it is specifically recommended in this guide. • Do not leave children alone or unattended in the area where the range is in
