Summary of the content on the page No. 1
L53H4/US (VCC-6594) GB 2001, 11, 9
INSTRUCTION MANUAL
VCC-6594
COLOR CCD CAMERA
About this manual
Before installing and using the camera, please read this manual
carefully. Be sure to keep it handy for later reference.
Summary of the content on the page No. 2
L53H4/US (VCC-6594) GB 2001, 11, 9 SANYO INDUSTRIAL VIDEO COLOR VIDEO CAMERA LIMITED WARRANTY OBLIGATIONS In order to obtain warranty service, the product must be delivered to and picked up from an Authorized Sanyo Service Center at the user’s expense, unless specifically stated otherwise in this warranty. The names and addresses of Authorized Sanyo Service Centers may be obtained by calling the toll-free number listed below. For product operation, authorized service center re
Summary of the content on the page No. 3
L53H4/US (VCC-6594) GB 2001, 11, 9 21605 Plummer Street, 1AC6P1P2413-- Chatsworth, California 91311 L53H4/US(1101KPS-CZ) Printed in Japan
Summary of the content on the page No. 4
L53H4/US (VCC-6594) GB 2001, 11, 9 Depending on the conditions of use, installation and environment, please be sure to make the appropriate settings and adjustments. If you FEATURES need help with installation and/or settings, please consult your dealer. Built-in interline transfer method 1/3" CCD, approx. 410,000 picture elements CONTENTS Equipped with a DSP (Digital Signal Processor) function Horizontal resolution, more than 520 TV lines INFORMATION TO USER . . . . . . . . . . . . . . .
Summary of the content on the page No. 5
L53H4/US (VCC-6594) GB 2001, 11, 9 INFORMATION TO USER This equipment has been tested and found to comply with the limits Safety Guard for a Class B digital device, pursuant to Part 15 of the FCC Rules. These limits are designed to provide reasonable protection THIS SYMBOL INDICATES THAT THERE ARE against harmful interference in a residential installation. This IMPORTANT OPERATING AND MAINTENANCE equipment generates, uses, and can radiate radio frequency INSTRUCTIONS IN THE LITERATURE energy and
Summary of the content on the page No. 6
L53H4/US (VCC-6594) GB 2001, 11, 9 PRECAUTIONS In case of problem Protect from humidity and dust Do not use the camera if smoke or a strange odour comes from the To prevent damages to the camera, do not install it where there is unit, or if it seems not to function correctly. Disconnect the power greasy smoke or steam, where the dampness may get too high, or cord immediately, and consult your dealer (or a Sanyo Authorized where there is a lot of dust. Service Centre). Protect from high temperatu
Summary of the content on the page No. 7
L53H4/US (VCC-6594) GB 2001, 11, 9 PARTS NAMES 1 Video output connector (VIDEO OUT: BNC type) Connect this connector to a device such as a VCR or monitor with a VIDEO IN connector. 2 Line phase adjustment volume (LINE PHASE) 4 1 When using two cameras or more, the image on the monitor may roll vertically when switching sources. This rolling can be minimized by turning this volume. 3 3 Power input terminal 2 24 V AC input terminal (AC 24 V, GND) 4 Power indicator (POWER) Comes on when the power t
Summary of the content on the page No. 8
L53H4/US (VCC-6594) GB 2001, 11, 9 PARTS NAMES 5 Lens mount cap The cap is installed to protect the lens mount section. Remove the lens mount cap before installing a lens (sold separately). 6 Flange-back adjustment screw (FLANGE BACK ADJ.) 7 5 7 Flange-back lock screw (FLANGE BACK LOCK) 6 8 8 Camera installation bracket 2 3 2 The bracket can be fixed at the top or bottom of the camera. When fixing the bracket, be sure to use the 1 longer screws and install the shorter screws on the opposite side
Summary of the content on the page No. 9
L53H4/US (VCC-6594) GB 2001, 11, 9 PARTS NAMES 9 Lens iris output connector (LENS) This 4-pin connector is used to send the DC control signal and power supply to an auto-iris type lens. F F Camera setup section (under the cover) 9 These settings are for when using a 1/3 inch CS mount DC (without EE internal amplifier) type lens. However, if due to installation conditions or environment the settings may need to be modified for best results (see "SETTINGS"). To access the controls, remove the cove
Summary of the content on the page No. 10
L53H4/US (VCC-6594) GB 2001, 11, 9 CONCERNING AUTO-IRIS LENSES DC type auto-iris lens VR301 A lens without amplifier circuit that operates only on a DC power source. In general, this type of lens is referred to as DC type coil lens or DC type non-amplifier lens. (Set the A.I. LENS switch to the DC position.) DC VIDEO VIDEO type auto-iris lens A. I. LENS A lens with amplifier circuit that operates on video signal and DC power source. In general, this type of lens is referred to as EE amplifier ty
Summary of the content on the page No. 11
L53H4/US (VCC-6594) GB 2001, 11, 9 MOUNTING THE LENS Please use a DC type auto-iris lens (sold separately). 1 Check the lens mount Do not use a lens if the length “L” is more than 5 mm. That may damage the camera and prevent proper installation. C mount type lens 2 L 1 Remove the lens mount cap from the camera. 2 Install the auto-iris lens. CS mount type lens Carefully align the lens mount with the camera opening, then turn the lens slowly to install it. C mount type lens 3 To allow for flange-b
Summary of the content on the page No. 12
L53H4/US (VCC-6594) GB 2001, 11, 9 MOUNTING THE LENS Rewiring the lens cable in the lens iris plug 1 Prepare the lens cable. 1 Cut the cable at the plug, then remove approx. 8 mm of the cable sheath and strip about 2 mm from each wire. 2 Install the lens iris plug. 2 Solder the cable to the pins following the correct pin layout (refer to the table and illustrations), then close the plug cover. Pin layout DC type lenses VIDEO type lenses Brake coil (–) +12 V DC (50 mA max.) 1 2 1 2 1 Brake coil (
Summary of the content on the page No. 13
L53H4/US (VCC-6594) GB 2001, 11, 9 CONNECTIONS 1 (A) 3 AC 24 V connection Push to insert the cable AC 24 V 2 (Video signal connections) GND ~ ~ : VIDEO IN : VIDEO OUT Coaxial cable type and maximum length Basic connection for monitoring or recording Cable type RG-59U (3C-2V), 250 m maximum. The peripheral devices (VCR, monitor, lens, etc.), AC adaptor Cable type RG-6U (5C-2V), 500 m maximum. and cables are sold separately. Cable type RG-11U (7C-2V), 600 m maximum. 1 Make the
Summary of the content on the page No. 14
L53H4/US (VCC-6594) GB 2001, 11, 9 SETTINGS The illustration shows the factory default settings for the switches in the camera setup section. The camera settings are described on the assumption that a DC type auto iris lens is being used. If you are using a VIDEO type auto iris lens, be sure to read the Note which is given. 6 9 Control name Position High speed electronic shutter (ES)/ 1/60 sec. 1 R B VR301 Electronic iris (EI) setting VR302 VR303 ON Auto gain control setting (HI/NORM) NORM 2 DC
Summary of the content on the page No. 15
L53H4/US (VCC-6594) GB 2001, 11, 9 SETTINGS Table A (switch 1 ~ 3) Electronic shutter settings and electronic iris 1 2 3 4 5 6 7 8 settings 1/60(AI) 1/100 1/500 1/1000 1/2000 1/4000 1/10000 EI When all of these switches are down, electronic shutter (1/60 sec or auto iris setting) is enabled. The electronic shutter can be set to one 12 3 1 23 1 23 1 23 12 3 1 23 1 23 1 23 of 7 speeds as shown in Table A. (Unit: sec.) Furthermore, when all switches are up, electronic iris setting is enabled. Autom
Summary of the content on the page No. 16
L53H4/US (VCC-6594) GB 2001, 11, 9 SETTINGS (MULTI mode: 64 sections) Backlight compensation setting This camera has two different backlight compensation functions: Normally backlight compensation switch 6 (MULT) and 7 (CENT) are set to the down (OFF) position. Change the backlight compensation switch settings 6 7 depending on the conditions. MULT mode: Use this position when applying backlight compensation to the whole of the screen. (CENT mode) CENT mode: Use this position when applying ba
Summary of the content on the page No. 17
L53H4/US (VCC-6594) GB 2001, 11, 9 SETTINGS White balance adjustment Lens iris adjustment Normally the switch 8 (WB) is set to the down (ATW: auto white If using a DC type auto-iris lens, you will need to set the LEVEL balance) position and the white balance is adjusted automatically. If a (VR301) volume when shooting in the conditions described below. manual white balance adjustment is necessary, follow the steps below. Set the switch 8 (WB) to the up (M: manual) position, then adjust the VR301
Summary of the content on the page No. 18
L53H4/US (VCC-6594) GB 2001, 11, 9 SETTINGS Line phase adjustment When using a camera switcher to connect 2 cameras or more to one monitor, there may be a vertical roll of the images when switched. In such a case, set as described below. 1 Set the switch 9 (SYNC) to the up (LL) position. 2 Switch the display on the monitor from camera 1 to camera 2. Adjust the LINE PHASE volume on camera 2 until the vertical roll of the image stops. If more than two cameras are used, please repeat this procedure
Summary of the content on the page No. 19
L53H4/US (VCC-6594) GB 2001, 11, 9 TROUBLESHOOTING Before taking the camera for repairs, please check below to make sure that the camera is used correctly. If it still does not perform correctly, please consult your dealer or a Sanyo Authorized Service Centre. No picture on the monitor screen Is the power turned on to all connected devices? Is the voltage correct? Are all the signal connecting cables correctly connected? Is the lighting sufficient? Has the lens cap been removed? Is the
Summary of the content on the page No. 20
L53H4/US (VCC-6594) GB 2001, 11, 9 SPECIFICATIONS Camera: Scanning system : NTSC standard TV system Power supply : 24 V AC, 60 Hz (525 TV lines, 30 frames/sec.) Power consumption : Approx. 2.8 W (with auto iris lens) Interlace : PLL 2:1 interlace Approx. 2.1 W (without auto iris lens) Image device : 1/3 inch solid state image device CCD Weight : Approx. 310 g (without lens) Picture elements : 811 (H) x 508 (V) Dimensions Effective picture : 768 (H) x 494 (V) elements 56 109 Synchronizing system
