Makita 4340CT user manual

User manual for the device Makita 4340CT

Device: Makita 4340CT
Category: Saw
Manufacturer: Makita
Size: 0.31 MB
Added : 12/1/2013
Number of pages: 16
Print the manual

Download

How to use this site?

Our goal is to provide you with a quick access to the content of the user manual for Makita 4340CT. Using the online preview, you can quickly view the contents and go to the page where you will find the solution to your problem with Makita 4340CT.

For your convenience

If looking through the Makita 4340CT user manual directly on this website is not convenient for you, there are two possible solutions:

  • Full Screen Viewing - to easily view the user manual (without downloading it to your computer), you can use full-screen viewing mode. To start viewing the user manual Makita 4340CT on full screen, use the button Fullscreen.
  • Downloading to your computer - You can also download the user manual Makita 4340CT to your computer and keep it in your files. However, if you do not want to take up too much of your disk space, you can always download it in the future from ManualsBase.
Makita 4340CT User manual - Online PDF
Advertisement
« Page 1 of 16 »
Advertisement
Print version

Many people prefer to read the documents not on the screen, but in the printed version. The option to print the manual has also been provided, and you can use it by clicking the link above - Print the manual. You do not have to print the entire manual Makita 4340CT but the selected pages only. paper.

Summaries

Below you will find previews of the content of the user manuals presented on the following pages to Makita 4340CT. If you want to quickly view the content of pages found on the following pages of the manual, you can use them.

Abstracts of contents
Summary of the content on the page No. 1

ENGLISH
Jig Saw
MODEL 4340T
MODEL 4340CT
MODEL 4340FCT
001905
DOUBLE
INSULATION
INSTR U CTION MANU AL
WARNING:
For your personal safety, READ and UNDERSTAND before using.
SAVE THESE INSTRUCTIONS FOR FUTURE REFERENCE.

Summary of the content on the page No. 2

SPECIFICATIONS Model 4340T 4340CT 4340FCT Length of stroke 26 mm 26 mm 26 mm Wood 135 mm (* 110 mm) 135 mm 135 mm Max. cutting capacities Steel 10 mm 10 mm 10 mm -1 2,800 800 - 2,800 800 - 2,800 Strokes per minute (min ) Overall length 236 mm 236 mm 236 mm Net weight 2.4 kg 2.4 kg 2.4 kg Safety class /II * For European countries • Due to our continuing programme of research and development, the specifications herein are subject to change without notice.  Note: Specifications may differ from c

Summary of the content on the page No. 3

GENERAL SAFETY RULES GEA001-3 WARNING: Read all instructions. Failure to follow all instructions listed below may result in electric shock, fire and/or serious injury. The term “power tool” in all of the warnings listed below refers to your mains-operated (corded) power tool or battery- operated (cordless) power tool. SAVE THESE INSTRUCTIONS Work area safety 10. Use safety equipment. Always wear eye protec- tion. Safety equipment such as dust mask, non-skid 1. Keep work area clean and well lit.

Summary of the content on the page No. 4

19. Store idle power tools out of the reach of chil- 6. Check for the proper clearance beyond the dren and do not allow persons unfamiliar with workpiece before cutting so that the blade will the power tool or these instructions to operate not strike the floor, workbench, etc. the power tool. Power tools are dangerous in the 7. Hold the tool firmly. hands of untrained users. 8. Make sure the blade is not contacting the work- 20. Maintain power tools. Check for misalignment or piece before the sw

Summary of the content on the page No. 5

FUNCTIONAL CAUTION: DESCRIPTION  Always be sure that the tool is switched off and unplugged before adjusting or checking function on the tool. 001906 Selecting the cutting action This tool can be operated with an orbital or a straight line (up and down) cut- ting action. The orbital cutting action thrusts the blade forward on the cutting stroke and greatly increases cutting speed. To change the cutting action, just turn the cutting action changing lever to the desired cutting action position.

Summary of the content on the page No. 6

001956 Workpiece to be cut Number on adjusting dial Wood 4 - 5 Mild steel 3 - 5 Stainless steel 3 - 4 Aluminum 3 - 5 Plastics 1 - 4 CAUTION:  The speed adjusting dial can be turned only as far as 5 and back to 1. Do not force it past 5 or 1, or the speed adjusting function may no longer work. The tools equipped with electronic function are easy to operate because of the following features. Constant speed control Electronic speed control for obtaining constant speed. Possible to get fine fin- is

Summary of the content on the page No. 7

001910 Keeping that situation, insert the saw blade into the blade clamp as far as the two protrusions of the blade can not be seen. 3 Return the tool opener to its original position. After installing, always make sure that the blade is securely held in place by trying to pull it out. CAUTION: 1  Do not open the tool opener excessively, or it may cause tool damage. 2 1. Blade clamp 2. Jig saw blade 3. Protrusions 001911 To remove the blade, open the tool opener to the position shown in the figu

Summary of the content on the page No. 8

001914 Bevel cutting CAUTION:  Always be sure that the tool is switched off and unplugged before tilting the tool base. With the tool base tilted, you can make bevel cuts at any angle between 0° and 45° (left or right). 001915 Loosen the bolt on the back of the base with the hex wrench. Move the base so that the bolt is positioned in the center of the bevel slot in the base. 1 3 2 1. Base 2. Bolt 3. Hex wrench 001916 Tilt the base until the desired bevel angle is obtained. The V-notch of the ge

Summary of the content on the page No. 9

Cutouts Cutouts can be made with either of two methods A or B. 001918 A) Boring a starting hole For internal cutouts without a lead-in cut from an edge, pre-drill a starting hole 12 mm or more in diameter. Insert the blade into this hole to start your cut. 1 1. Starting hole 001919 B) Plunge cutting You need not bore a starting hole or make a lead-in cut if you carefully do as follows. (1) Tilt the tool up on the front edge of the base with the blade point positioned just above the workpiece sur

Summary of the content on the page No. 10

001921 Dust extraction 1 The dust nozzle (accessory) is recommended to perform clean cutting opera- tions. To attach the dust nozzle on the tool, insert the hook of dust nozzle into the hole in the base. The dust nozzle can be installed on either left or right side of the base. 2 1. Dust nozzle 2. Base 001922 001923 Then connect a Makita vacuum cleaner to the dust nozzle. CAUTION: If you try to remove the dust nozzle forcibly, the hook of the dust nozzle can be diminished and removed unintentio

Summary of the content on the page No. 11

001924 1. Straight cuts When repeatedly cutting widths of 160 mm or less, use of the rip fence will assure fast, clean, straight cuts. To install, insert the rip fence into the rectan- gular hole on the side of the tool base with the fence guide facing down. Slide the rip fence to the desired cutting width position, then tighten the bolt to secure it. 1 1. Rip fence 001925 3 1 2 1. Bolt 2. Fence guide 3. Hex wrench 001926 2. Circular cuts When cutting circles or arcs of 170 mm or less in radius,

Summary of the content on the page No. 12

004446 Guide rail adapter set (accessory) When cutting parallel and uniform width or cutting straight, the use of the guide rail and the guide rail adapter will assure the production of fast and clean cuts. 004447 To install the guide rail adapter, insert the rule bar into the square hole of the base as far as it goes. Secure the bolt with the hex wrench securely. 2 1 1. Bolt 2. Rule bar 004448 Install the guide rail adapter on the rail of the guide rail. Insert the rule bar into the square hole

Summary of the content on the page No. 13

001929 Anti-splintering device For splinter-free cuts, the anti-splintering device can be used. To install the anti-splintering device, move the tool base all the way forward and fit it from the back of tool base. When you use the cover plate, install the anti-splintering device onto the cover plate. 1 CAUTION:  The anti-splintering device cannot be used when making bevel cuts. 2 1. Base 2. Anti-splintering device MAINTENANCE CAUTION:  Always be sure that the tool is switched off and unplugged

Summary of the content on the page No. 14

Memo 14

Summary of the content on the page No. 15

Memo 15

Summary of the content on the page No. 16

Makita Corporation Anjo, Aichi, Japan 884426E228


Alternative user manuals
# User manual Category Download
1 Makita 2107FK User manual Saw 49
2 Makita 2414DB User manual Saw 4
3 Makita 2704X1 User manual Saw 10
4 Makita 2414NB User manual Saw 82
5 Makita 4101RH User manual Saw 8
6 Makita 24016 User manual Saw 10
7 Makita 4191DZ User manual Saw 1
8 Makita 3706 User manual Saw 2
9 Makita 4112H User manual Saw 4
10 Makita 4191DWA User manual Saw 2
11 Makita 2704 User manual Saw 224
12 Makita 4114 User manual Saw 1
13 Makita 4200H User manual Saw 7
14 Makita 4305T User manual Saw 66
15 Makita 4324 User manual Saw 97
16 Sony XS-L12S User manual Saw 8
17 Sony XS-L10S User manual Saw 1
18 3Com 3CRWDR200A-75 User manual Saw 6
19 Agilent Technologies 16193A User manual Saw 4
20 Aiphone AP-10M User manual Saw 1