Summary of the content on the page No. 1
TEC Laser Scanner
LS-780 SERIES
Owner’s Manual
Summary of the content on the page No. 2
Summary of the content on the page No. 3
CE Compliance (for EU only) This product complies with the requirements of EMC and Low Voltage Directives includ- ing their amendments. Caution: For U.S and Canada, use a UL Listed or Recognized, ITE or Class 2 power supply unit having a L-shaped output connector. For Europe, use a CE marked ITE or Class 2 power supply unit having a L-shaped output connector. Rated output of the power supply unit shall be 12 Vdc –10% 800 mA or more. FCC Notice (for USA only) This equipment has been tested and fo
Summary of the content on the page No. 4
EO1-19036 Safety Summary Safety Summary Personal safety in handling or maintaining the equipment is extremely important. Warnings and Cautions necessary for safe handling are included in this manual. All warnings and cautions contained in this manual should be read and understood before handling or maintaining the equipment. Do not attempt to effect repairs or modifications to this equipment. If a fault occurs that cannot be rectified using the procedures described in this manual, turn off th
Summary of the content on the page No. 5
EO1-19036 Safety Summary Disconnect Disconnect If foreign objects (metal fragments, When unplugging the power the plug. the plug. water, liquids) enter the machines, cords, be sure to hold and pull on first turn off the power switches and the plug portion. Pulling on the cord disconnect the power cord plugs from portion may cut or expose the inter- the outlet, and then contact your nal wires and cause fire or electric authorized TOSHIABA TEC repre- shock. sentative for assistance. Continue
Summary of the content on the page No. 6
EO1-19036 LS-780 SERIES TABLE OF CONTENTS Page 1. INTRODUCTION..................................................................................1 2. LASER SAFETY..................................................................................1 3. APPEARANCE AND NOMENCLATURE ............................................2 4. OPERATING PROCEDURE ................................................................4 5. BARCODE READING ......................................................................
Summary of the content on the page No. 7
EO1-19036 LS-780 SERIES 1. INTRODUCTION Thank you for purchasing the TEC LS-780 Series Laser Scanner. This manual describes the functions and handling of this Scanner and should be read carefully to help gain maximum performance and life from your Scanner. For most queries please refer to this manual and keep it safe for future reference. 2. LASER SAFETY n Maintenance and Safety 1. Caution—use of controls or adjustments or performance of procedures other than those specified herein may result i
Summary of the content on the page No. 8
EO1-19036 LS-780 SERIES 3. APPEARANCE AND NOMENCLATURE 3.1 Appearance Volume Switch LED (Green/Red) Connector for AC Adapter on the Market Push Switch Scanner Window Interface Cable Connector Scanner Window: Read a barcode of an item. (For barcode readable range, refer to 5. BARCODE READING.) Connector for AC Adapter Connects the AC Adapter on the market. on the market: (Complying with EIAJ RC6705.) Interface Cable Connector: Connects the Interface Connector Cable (26-pin). OCIA type, RS-232C ty
Summary of the content on the page No. 9
EO1-19036 LS-780 SERIES 3.2 Switch Panel Volume Switch LED (Green/Red) Push Switch LED(Green/Red): Indicates scanner status using two-color LED (green and red). (The red LED lights when the scanner is ready to read a barcode and the green LED lights when a barcode is read normally.) Push Switch: Pressed to return the scanner to reading standby state in auto-power off mode.) Volume Switch: Adjusts the buzzer volume of the scanner. Each time the volume switch is pressed, the buzzer volume changes
Summary of the content on the page No. 10
EO1-19036 LS-780 SERIES 4. OPERATING PROCEDURE Power Supply (1) When the AC Adapter on the market is used: When the AC adapter is equipped with the power switch, the scanner is turned on and off by turning on and off the power switch. When the AC Adapter is not equipped with the power switch, the power is supplied by plugging in the power cord (no RPC function can be used). (2) When the power is supplied from the host (ECR/POS): The power can be supplied via the interface cable. If the host can
Summary of the content on the page No. 11
50 mm to MAX 200 mm EO1-19036 LS-780 SERIES 5.2 Effective Scanning Zone 75 53.5 (LS-780H) 81.8 90 46.3 (LS-780H) 79 53.5 (LS-780H) 5.3 How to Read Target the center of the Scanner Window so that the scanner can read a barcode of an item in the range at 50 mm to 200 mm above from the Scanner Window surface. Article CAUTION 1. Do not contact the item and the Scanner Window. 2. Moving the item perpendicularly to the Scanner Window makes it difficult to read the barcode. Rea
Summary of the content on the page No. 12
EO1-19036 LS-780 SERIES 6. MAINTENANCE To maintain reading precision above the prescribed level, keep the Scanner Window clean. To clean the Top Window, use a soft cloth. Remove the Top Window as shown in the figure below, and wipe the Top Window softly using a dry soft cloth. When the Top Window is badly soiled, use a cloth after moistening it with water and wringing water from it. Then wipe the Top Window again using a dry cloth. Clean the Under Window in the same manner. Be careful not to dam
Summary of the content on the page No. 13
EO1-19036 LS-780 SERIES 7. TROUBLESHOOTING • When an error is detected at the power ON… This scanner has the self-diagnosis function to detect an internal error when the power is turned ON. If an error is found at this time, the scanner informs you of error occurrence by the LED and the buzzer. Number of the LED flickering and the buzzer beep is predetermined according to the error contents as shown below. The error indication is repeated at the one second interval until the power of the scanner
Summary of the content on the page No. 14
EO1-19036 LS-780 SERIES • When the scanner cannot read a barcode... Cause Action • The top window of the scanner is dirty or dewed. • Clean the top window. • Barcode system does not correspond to scanner • Reading a barcode is unavailable. Use the barcode specification. system corresponding to the scanner specification. • Barcode has a defect. (Print of a barcode is too • Reading a barcode is unavailable. light, dirty, blurred, or defaced.) Read a perfect barcode attached to the same article. E
Summary of the content on the page No. 15
Summary of the content on the page No. 16
PRINTED IN JAPAN M EO1-19036
