Summary of the content on the page No. 1
WZ16 Integrated IR Bullet
Camera
WZ16
en Installation Manual
Summary of the content on the page No. 2
Summary of the content on the page No. 3
WZ16 Integrated IR Bullet Camera Table of Contents | en 3 Table of Contents 1Safety 4 1.1 Safety Precautions 4 1.2 Important Safety Instructions 4 1.3 Important Notices 6 1.4 FCC & ICES compliance 9 1.5 CSA certification 12 1.6 Warranty / Limitation of Liability 12 2 Introduction 14 2.1 Parts Included 14 3 Installation and Connection 15 4 Configuration 18 4.1 Adjusting the Zoom 18 4.2 Adjusting the Focus 19 4.3 Adjusting the Video Output Brightness 19 5 Troubleshooting 20 5.1 Troubleshooting Tip
Summary of the content on the page No. 4
4 en | Safety WZ16 Integrated IR Bullet Camera 1Safety 1.1 Safety Precautions DANGER! High risk: This symbol indicates an imminently hazardous situation such as “Dangerous Voltage” inside the product. If not avoided, this will result in an electrical shock, serious bodily injury, or death. WARNING! Medium risk: Indicates a potentially hazardous situation. If not avoided, this could result in minor or moderate bodily injury. CAUTION! Low risk: Indicates a potentially hazardous situation. If
Summary of the content on the page No. 5
WZ16 Integrated IR Bullet Camera Safety | en 5 9. Do not put objects inside the camera. Make sure that no metal objects or flammable substances enter the camera. This may cause fire, short-circuits and other damages. 10. Be careful when handling the camera. To prevent damage, do not drop the camera or subject it to strong shock or vibration. 11. Do not defeat the safety purpose of the polarized or grounding-type plug. A polarized plug has two blades with one wider than the other. A groundi
Summary of the content on the page No. 6
6 en | Safety WZ16 Integrated IR Bullet Camera 1.3 Important Notices Accessories - Do not place this unit on an unstable stand, tripod, bracket, or mount. The unit may fall, causing serious injury and/or serious damage to the unit. Use only with the cart, stand, tripod, bracket, or table specified by the manufacturer. When a cart is used, use caution and care when moving the cart/apparatus combination to avoid injury from tip-over. Quick stops, excessive force, or uneven surfaces may caus
Summary of the content on the page No. 7
WZ16 Integrated IR Bullet Camera Safety | en 7 Coax grounding: – Ground the cable system if connecting an outside cable system to the unit. – Connect outdoor equipment to the unit's inputs only after this unit has had its grounding plug connected to a grounded outlet or its ground terminal is properly connected to a ground source. – Disconnect the unit's input connectors from outdoor equipment before disconnecting the grounding plug or grounding terminal. – Follow proper safety precautions
Summary of the content on the page No. 8
8 en | Safety WZ16 Integrated IR Bullet Camera Electrostatic-sensitive device - Use proper CMOS/MOS-FET handling precautions to avoid electrostatic discharge. NOTE: Wear required grounded wrist straps and observe proper ESD safety precautions when handling the electrostatic- sensitive printed circuit boards. Moving - Disconnect the power before moving the unit. Move the unit with care. Excessive force or shock may damage the unit and the hard disk drives. Outdoor signals - The installation f
Summary of the content on the page No. 9
WZ16 Integrated IR Bullet Camera Safety | en 9 safety ground are connected and grounding loops are causing interference in the video signal, use an isolation transformer (available separately from Bosch). CAUTION! Connecting System ground to Safety ground may result in ground loops that can disrupt the CCTV system. Video loss - Video loss is inherent to digital video recording; therefore, Bosch Security Systems cannot be held liable for any damage that results from missing video informatio
Summary of the content on the page No. 10
10 en | Safety WZ16 Integrated IR Bullet Camera base fitted under the camera and a conduit fitting adaptor in the wall of the PSU box. – Reorient or relocate the receiving antenna; – Increase the separation between the equipment and receiver; – Connect the equipment into an outlet on a circuit different from that to which the receiver is connected; – Consult your Bosch Service Center, dealer, or an experienced radio/TV technician for further advice. Intentional or unintentional modifications
Summary of the content on the page No. 11
WZ16 Integrated IR Bullet Camera Safety | en 11 successivement hors et sous tension, tout en contrôlant la réception radio ou télévision. L'utilisateur peut parvenir à éliminer les interférences éventuelles en prenant une ou plusieurs des mesures suivantes: – Modifier l'orientation ou l'emplacement de l'antenne réceptrice; – Éloigner l'appareil du récepteur; – Brancher l'appareil sur une prise située sur un circuit différent de celui du récepteur; – Consulter le revendeur ou un technicien q
Summary of the content on the page No. 12
12 en | Safety WZ16 Integrated IR Bullet Camera 1.5 CSA certification Disclaimer CSA has not tested the performance or reliability of the security or signaling aspects of this product. CSA has only tested fire, shock and/or casualty hazards as outlined in CSA's Standard(s) for Safety for Audio, Video and Similar Electronic Apparatus. Safety Requirements UL 60065. CSA Certification does not cover the performance or reliability of the security or signaling aspects of this product. CSA MAKES
Summary of the content on the page No. 13
WZ16 Integrated IR Bullet Camera Safety | en 13 The foregoing warranty is subject to Buyer’s (i) promptly written claim and (ii) timely provision to BOSCH Security Systems of an opportunity to inspect and test the Product claimed to be defective. Such inspection may be on Buyer’s premises and/or BOSCH SecuritySystems may request the return of the Product at Buyer’s expense. However, BOSCH SecuritySystems shall not be responsible for packing, inspection, or labor costs in connection with t
Summary of the content on the page No. 14
14 en | Introduction WZ16 Integrated IR Bullet Camera 2 Introduction The WZ16 Integrated IR Bullet Camera is a night vision DSP Color CCD camera that uses a 1/3 in. CCD solid-state imaging device that provides superior performance. The camera can be installed easily in most indoor and outdoor locations. Features include: – Day/night operation – Infrared, photocell-controlled LEDs – Weight of less than 1.5 pounds / 0.6 kg – IP67 rating – Operates at temperature range from -30 °C to +55 °C (
Summary of the content on the page No. 15
WZ16 Integrated IR Bullet Camera Installation and Connection | en 15 3 Installation and Connection DANGER! RISK OF ELECTRIC SHOCK! DO NOT OPEN THE UNIT! WARNING! To prevent injury, this apparatus must be securely attached to the floor/wall in accordance with the following installation instructions. CAUTION! Do not install the camera near electric or magnetic fields. If possible, do not install in a kitchen or boiler room as heat will affect the camera. CAUTION! Do not use a power sourc
Summary of the content on the page No. 16
16 en | Installation and Connection WZ16 Integrated IR Bullet Camera Figure 3.1 Camera mounted on ceiling Figure 3.2 Camera mounted (from bottom) on Wall | 1.0 | 2011.02 Installation Manual Bosch Security Systems, Inc.
Summary of the content on the page No. 17
WZ16 Integrated IR Bullet Camera Installation and Connection | en 17 Figure 3.3 Camera mounted (from top) on Wall 4. Connect the camera to the video monitor. Bosch recommends using a monitor with a CCTV quality 75Ω video impedance level. If your monitor is switched to high impedance, please adjust the monitor accordingly. Figure 3.4 Standard 12 VDC BNC(RCA) Connection Number Description 1 12 VDC or 24 VAC regulated power supply 2 Video in 3 BNC (RCA) Female video Bosch Security Systems, Inc.
Summary of the content on the page No. 18
18 en | Configuration WZ16 Integrated IR Bullet Camera 4 Configuration Follow the steps below to adjust the zoom and focus. Remove the lens cap before making adjustments, then replace it when you finish. Refer to the figure below. Figure 4.1 Lens adjustment Number Description 1Zoom control 2 Focus control 3 Video brightness CAUTION! To prevent humidity problems, the camera must be installed in dry conditions. Removing the lens cap in a wet or humid environment may result in condensation on
Summary of the content on the page No. 19
WZ16 Integrated IR Bullet Camera Configuration | en 19 4.2 Adjusting the Focus 1. Loosen the focus lock screw by turning it counterclockwise. 2. Adjust the focus by moving the focus lever to near side or far side. 3. Turn the focus lock screw clockwise to tighten the focus lever after adjustment. 4.3 Adjusting the Video Output Brightness Adjust the brightness from VR according to the environment. Bosch Security Systems, Inc. Installation Manual | 1.0 | 2011.02
Summary of the content on the page No. 20
20 en | Troubleshooting WZ16 Integrated IR Bullet Camera 5 Troubleshooting 5.1 Troubleshooting Tips Before sending the camera out for repair, check the items below. If the problem persists after checking these items, contact your service center. - If no image appears, verify that: – The coaxial cable is attached securely. – The power and voltage are normal. – There is adequate illumination. - If the image is unclear, verify that: – The lens is in focus. – The lens is not dirty. Dirt or fingerp
