Summary of the content on the page No. 1
SNC-C7478
36x Network Smart Dome Camera
User Manual
imagine the possibilities
Thank you for purchasing this Samsung product.
To receive more complete service,
please visit our website.
www.samsungsecurity.com
Summary of the content on the page No. 2
safety information CAUTION RISK OF ELECTRIC SHOCK. DO NOT OPEN CAUTION: TO REDUCE THE RISK OF ELECTRIC SHOCK, DO NOT REMOVE COVER (OR BACK) NO USER SERVICEABLE PARTS INSIDE. REFER SERVICING TO QUALIFIED SERVICE PERSONNEL. This symbol indicates that dangerous voltage consisting a risk of electric shock is present within this unit. This exclamation point symbol is intended to alert the user to the presence of important operating and maintenance (servicing) instructions in the literature accomp
Summary of the content on the page No. 3
safety information CAUTION 1. Do not drop objects on the product or apply strong blows to it. Keep away from a location subject to excessive vibration or magnetic interference. 2. Do not install in a location subject to high temperature (over 140°F), low temperature (below -49°F), or high humidity. Doing so may cause fi re or electric shock. 3. If you want to relocate the already installed product, be sure to turn off the power and then move or reinstall it. 4. Remove the power plug from the ou
Summary of the content on the page No. 4
important safety instructions 1. Read these instructions. 2. Keep these instructions. 3. Heed all warnings. 4. Follow all instructions. 5. Do not use this apparatus near water. 6. Clean only with dry cloth. 7. Do not block any ventilation openings. Install in accordance with the manufacturer’s instructions. 8. Do not install near any heat sources such as radiators, heat registers, or other apparatus (including amplifi ers) that produce heat. 9. Do not defeat the safety purpose of the polarized o
Summary of the content on the page No. 5
contents Introduction Features 7 Recommended PC Specifi cations 8 Compatible IP Routers 8 Product & Accessories 9 Parts Name & Functions 10 Installation DIP Switch Setup 11 Installation Using Pole Mount Bracket 12 Cabling 15 Inserting/Removing an micro SDHC Memory Card 17 Memory Card Information (not included) 18 Operation Check points before operation 19 Preset and Pattern Function Pre-Check 19 Auto Calibration 19 Starting OSD Menu 19 Reserved Preset
Summary of the content on the page No. 6
contents Connecting the Camera Directly to Local Area Networking 42 Searching for the Camera 43 Setting Static IP Manual Network Setting 44 Automatic Network Setting 46 Setting Dynamic IP Dynamic IP Setting 47 Port Forwarding (Port Mapping) Setting 47 Using the Camera Connecting to the Camera 48 Installing ActiveX 49 Web Viewer Main Screen 51 Using the Camera 52 Using the SD Search Viewer Screen 54 Setup Tool Setting the camera 55 Video & Audio Confi gura
Summary of the content on the page No. 7
introduction � Max. 8 set of Auto Pan can be stored. This enables FEATURES to move camera repetitively between two preset positions with designated speed. ❖ Network Specifi cations � Max. 4 of Patterns can be recorded and played back. � Powerful Dual Stream by using DSP based This enables to move camera to follow any trajectory MPEG4, MJPEG compression operated by joystick as closely as possible. � Superior Video Quality and System Stability. � Max. 8 set of Scan action can be stored. � Hig
Summary of the content on the page No. 8
introduction RECOMMENDED PC SPECIFICATIONS � CPU : Pentium4/2.4GHz or higher � Operating System : Windows XP(Service Pack 2) / Windows Vista � Resolution : 1024x768 pixels or higher � RAM : 512MB or higher � Web Browser : Internet Explorer 6.0 or higher � Video Card : Radeon, Nvidia � Video Memory : 128MB � DirectX 8.1 or higher COMPATIBLE IP ROUTERS � Linksys � D-Link � Netgear 8 – 36x Network Smart Dome Camera
Summary of the content on the page No. 9
introduction PRODUCT & ACCESSORIES ❖ Product Wall Mount Type Ceiling Mount Type ❖ Accessories Hexagonal wrench Water proof tape Housing Safety Cable Hanger Screw & Plastic Anchor (4pcs) User Manual / IP Installer CD Quick Guide Safety Cable Hole Template Cross Cable Core Filter English – 9
Summary of the content on the page No. 10
introduction PARTS NAME & FUNCTIONS SUN SHIELD & UPPER HOUSING PTZ MECHANISM DOME SAFETY CABLE NETWORK BOX FAN & HEATER CABLE FAN HOUSING SAFETY CABLE HANGER HEATER DOME COVER • Dome Cover • Wall/Ceiling mount Bracket Do not detach protection vinyl from dome cover These are used to install the camera on the wall or before fi nishing all installation process to protect dome ceiling and have Network box in them. cover from scratches or dust. In the dome cover, there are Fan and Heater to • Net
Summary of the content on the page No. 11
Installation ❖ Communication Protocol Setup DIP SWITCH SETUP Before you install the camera, you should set the DIP ON ON switches to confi gure the camera ID, Baud rate and communication protocol. 12 3 4 56 78 Protocol Baud Rate 0x00 : Auto Protocol 0x00 : 2400 � Select the appropriate Protocol with DIP switch 0x03 : SAMSUNG 0x01 : 4800 combination. 0x02 : 9600 Switch State 0x03 : 19200 Protocol Pin1 Pin2 Pin3 Pin4 0x04 : 38400 OFF OFF OFF OFF Auto Protocol ON ON OFF OFF SAMSUNG RS-
Summary of the content on the page No. 12
installation ❖ RS-485 Termination Resistor 3. After locating the wall mount bracket on the anchor bolts properly. Tighten the nuts for anchor bolts ON ON 12 3 4 56 78 � Pin 8 is used for ON/OFF of RS-485 Termination. Normally, it must be OFF state. Especially when you have trouble with long Daisy chain style connection, turn ON this termination switch of last camera. – Pin 8 : RS-485 Termination Resistor (ON/OFF) INSTALLATION USING POLE MOUNT BRACKET 1. Using the paper template, mark the
Summary of the content on the page No. 13
installation 5. Press the PTZ mechanism's A, B handles and 7. Care must be taken dome cover is hung by pull out for Main Cable connection. internal safety cable properly. Plug fan/heater cables into the connectors in the housing. A B 6. Wrap the pipe thread of the housing top by Water proof tape [1]. After hooking the safety cable on the hole of pipe [2], attach the upper housing to mount bracket by turning it at least seven turns [3]. To fi x the upper 8. Plug the connector of cable from
Summary of the content on the page No. 14
installation 9. After checking the orientation of one touch 11. Close the dome cover. Care must be taken to connector in the upper housing, press the PTZ locate dome cover by matching the “Arrow” mechanism into hook in the upper housing. mark. 12. Tighten four screws on the dome cover in sequence as shown in the picture bellow. 10. To lock the PTZ mechanism to the upper housing, press the two black handles till it sounds snap. 4 1 2 3 To maintain the best sealing, the t
Summary of the content on the page No. 15
installation CABLING ❖ Power Connection Main Cable ALARM OUTPUT Pre-Amp 12 3 4 ALARM INPUT Speaker 12 34 G 5 67 8 Audio Out AC 24V POWER Power AC 24V Audio In AUDIO IN OUT F.G. BNC Video Microphone Pre-Amp LAN Cable � Please, check the voltage and current capacity of rated power carefully. Rated Power Input Voltage Range Current Consumption AC 24V AC 19V ~29V 23W(Heater Off) / 55W(Heater On) ❖ RS-485 Communication � For PTZ control, connect this line to keyboard and DVR. To control multiple cam
Summary of the content on the page No. 16
installation ❖ Video Connection � Connect with BNC coaxial cable. ❖ Audio Input/Ouput Connection 1. Connect the AUDIO IN port of the camera with the microphone directly or LINE OUT port of the amplifi er that the microphone is connected to direct Mic Connection: Set Audio Input Gain high (10). Refer to page 56 in this Manual. Line Out Connection: Set Audio Input Gain low (1). Refer to page 56 in this Manual. 2. Connect the AUDIO OUT port of the camera with the LINE IN port of the speaker. If th
Summary of the content on the page No. 17
installation INSERTING/REMOVING AN MICRO SDHC MEMORY CARD ❖ Inserting an Micro SDHC Memory Card � Push the Micro SDHC memory card in the direction of the arrow shown in the diagram. AC 24V AC 24V AUDIO IN OUT Do not force the memory card in. If you can’t insert the memory card into the slot with ease, you might be inserting the card in J the wrong direction. Forcibly inserting a memory card could lead to its damage. ❖ Removing an Micro SDHC Memory Card � Gently press down on the exposed end
Summary of the content on the page No. 18
installation MEMORY CARD INFORMATION (NOT INCLUDED) ❖ What is a memory card? The memory card is an external data storage device that has been developed to offer an entirely new way to record and share video, audio, and text data using digital devices. ❖ Selecting a memory card that’s suitable for you Your camera supports Micro SDHC memory cards. You may, however, experience compatibility issues depending on the model and make of the memory card. Your camera supports Micro SD memory cards. Howev
Summary of the content on the page No. 19
operation CHECK POINTS BEFORE STARTING OSD MENU OPERATION � Function Using the OSD menu, Preset, Pattern, Auto Pan, � Before power is applied, please check the cables Scan and Alarm Input function can be confi gured for carefully. each application. � The camera ID of the controller must be identical to � Enter Menu that of the camera to be controlled. The camera ID can be checked in the System Information of OSD [95] Menu. � If your controller supports multi-protocols, the proto
Summary of the content on the page No. 20
operation PRESET PATTERN � Function � Function Max. 127 positions can be stored as Preset position. Pattern Function is that a camera memorizes the path The Preset number can be assigned from 1 to 128, (mostly curve path) by joystick of controller for assigned but 95 is reserved for starting OSD menu. time and revives the path exactly as it memorized. Camera characteristics (i.e. White Balance, Auto 4 Patterns are available and Maximum 1000 Exposure) can be set up independently for each pre
