Summary of the content on the page No. 1
DS00387ACN_LSW-6_6.5.qxp 11/18/04 6:55 PM Page a
INSTALLATION & USER GUIDE
For Accurate Music
and Voice Reproduction
from In-Wall Locations
LSW-6/6.5
6-1/2” IN-WALL LOUDSPEAKER
Summary of the content on the page No. 2
DS00387ACN_LSW-6_6.5.qxp 11/18/04 6:55 PM Page b LSW-6/6.5 6-1/2” IN-WALL LOUDSPEAKER TABLE OF CONTENTS Features............................................................................................................................1 Product Overview...........................................................................................................1 Package Contents ..........................................................................................................2 Prep
Summary of the content on the page No. 3
DS00387ACN_LSW-6_6.5.qxp 11/18/04 6:55 PM Page 1 FEATURES: LSW-6 FEATURES: LSW-6.5 ■ 6-1/2” talc filled polypropylene woofer ■ 6-1/2” injection-molded polypropylene with a treated urethane surround woofer with butyl rubber surround ■ 3/4” pivoting liquid cooled polycarbonate ■ 1” pivoting liquid cooled soft dome dome tweeter tweeter ■ Moisture and UV resistant ■ Baffle mounted Bass and Treble controls (0, -3dB) ■ Rust proof aluminum grilles ■ Mois
Summary of the content on the page No. 4
DS00387ACN_LSW-6_6.5.qxp 11/18/04 6:55 PM Page 2 PACKAGE CONTENTS INSTALLATION ■ Speakers x 2 Installation Existing Construction: ■ Speaker frames x 2 1. Using your stud locator, identify the ■ Speaker grilles x 2 location of the studs on each side of the ■ Speaker brackets x 2 proposed speaker mounting location. ■ Wings for new construction x 4 2. Mark their edges, using masking tape. ■ #6 x 1-5/8” Philips head drywall screws x 6 3. Repeat this process fo
Summary of the content on the page No. 5
DS00387ACN_LSW-6_6.5.qxp 11/18/04 6:55 PM Page 3 10. Attach the frame to the bracket by Installation New Construction: screwing the frame to the bracket using The speaker brackets should be installed the supplied screws. NOTE: Do not over prior to the drywall. tighten the screws, this will distort the 1. Attach the wings to the bracket by frame and the grille will not fit. snapping them into the sides of the 11. The screws should pull the frame and bracket. (See Figure 1). To short
Summary of the content on the page No. 6
DS00387ACN_LSW-6_6.5.qxp 11/18/04 6:55 PM Page 4 8. In unique situations where the bracket 13. Strip 1/4” of insulation from the end of must be located precisely next to a joist, each wire. the bracket has “emergency” screw 14. Tightly twist the end of each wire until holes located on its snap-on tabs. Break no frayed ends remain. away two of the outer mounting tabs on 15. Attach the speaker wires to the speaker the side you wish to affix, see Figure 3. terminal connectors. Connect t
Summary of the content on the page No. 7
DS00387ACN_LSW-6_6.5.qxp 11/18/04 6:55 PM Page 5 Figure 4 Mounting Screws 1. Locate the dimples on the front baffle. 2. Insert the screws through the dimples until they are securely in place. IMPORTANT SAFETY INSTRUCTIONS When installing LSW-6, LSW-6.5 speakers in a ceiling or if the installation is located in an earthquake zone, it is recommended that you utilize the enclosed self-tapping screws to secure the baffle to the frame See Figure 4. DIRECTING THE TWEETER The tweeter is dir
Summary of the content on the page No. 8
DS00387ACN_LSW-6_6.5.qxp 11/18/04 6:55 PM Page 6 SETTING THE BASS AND TREBLE CUT SWITCHES LSW-6.5 Loudspeakers ONLY LSW-6.5 loudspeakers feature separate baffle-mounted bass and treble controls for fine-tuning after installation. Each control provides for approximately 3dB of Bass or Treble reduction. See figure 7. Listen to a well-recorded piece of music at Figure 8 the user’s favorite listening position. First, Removing the listen for bass boominess, particularly when Speaker
Summary of the content on the page No. 9
DS00387ACN_LSW-6_6.5.qxp 11/18/04 6:55 PM Page 7 SPECIFICATIONS: LSW-6 Power handing: 10 – 75 watts Frequency response: 65Hz-20kHz +/- 3dB Impedance: 8 ohms Dimensions: 8-3/4” x 11-11/16” outside dimension 7-5/8” x 10-5/8” hole cutout 3-5/8” deep when installed in 1/2” drywall Warranty: 5 year limited Figure 9 SPECIFICATIONS: LSW-6.5 OPERATION Power handing: Listening at Higher Volumes: 10 – 125 watts It requires more power to achieve a Frequency response: reasonab
Summary of the content on the page No. 10
DS00387ACN_LSW-6_6.5.qxp 11/18/04 6:55 PM Page 8 LIMITED WARRANTY A factory Return Authorization Number will JobSite Systems (“JOBSITE”), a Niles be sent to you. DO NOT RETURN ANY Audio Corporation company, warrants its UNIT WITHOUT FIRST RECEIVING passive products (those not requiring AC or WRITTEN AUTHORIZATION AND battery power) to the original purchaser to SHIPPING INSTRUCTIONS FROM be free of manufacturing defects in material JOBSITE. and workmanship for a period of ten years from d
Summary of the content on the page No. 11
DS00387ACN_LSW-6_6.5.qxp 11/18/04 6:55 PM Page 9 NOTES: 9
Summary of the content on the page No. 12
DS00387ACN_LSW-6_6.5.qxp 11/18/04 6:55 PM Page 10 JOBSITE SYSTEMS 12331 S.W. 130 STREET, MIAMI, FLORIDA 33186 P (866) 4JB-SITE (866-452-7483) – F (305) 238-0185 WWW.JOBSITESYSTEMS.COM JobSite Systems, a Niles Audio Corporation company, 12331 S.W. 130 Street, Miami, Fl 33186. ©2004 Niles Audio Corporation. JobSite, Pure Custom and Niles are registered trademarks of Niles Audio Corporation and the JobSite Logo is a trademark of Niles Audio Corporation. All other trademarks are the property
