Boston Acoustics RX57 user manual

User manual for the device Boston Acoustics RX57

Device: Boston Acoustics RX57
Category: Speaker
Manufacturer: Boston Acoustics
Size: 0.93 MB
Added : 10/18/2013
Number of pages: 16
Print the manual

Download

How to use this site?

Our goal is to provide you with a quick access to the content of the user manual for Boston Acoustics RX57. Using the online preview, you can quickly view the contents and go to the page where you will find the solution to your problem with Boston Acoustics RX57.

For your convenience

If looking through the Boston Acoustics RX57 user manual directly on this website is not convenient for you, there are two possible solutions:

  • Full Screen Viewing - to easily view the user manual (without downloading it to your computer), you can use full-screen viewing mode. To start viewing the user manual Boston Acoustics RX57 on full screen, use the button Fullscreen.
  • Downloading to your computer - You can also download the user manual Boston Acoustics RX57 to your computer and keep it in your files. However, if you do not want to take up too much of your disk space, you can always download it in the future from ManualsBase.
Boston Acoustics RX57 User manual - Online PDF
Advertisement
« Page 1 of 16 »
Advertisement
Print version

Many people prefer to read the documents not on the screen, but in the printed version. The option to print the manual has also been provided, and you can use it by clicking the link above - Print the manual. You do not have to print the entire manual Boston Acoustics RX57 but the selected pages only. paper.

Summaries

Below you will find previews of the content of the user manuals presented on the following pages to Boston Acoustics RX57. If you want to quickly view the content of pages found on the following pages of the manual, you can use them.

Abstracts of contents
Summary of the content on the page No. 1

RX47
RX57
RX57DIN
RX67
RX67DIN
RX87
RX97
®
Boston Rally Series
Coaxial Speaker Systems
Installation Instructions

Summary of the content on the page No. 2

Specifications RX97 RX87 RX67 RX67DIN RX57 RX57DIN RX47 1 1 1 1 ⁄ ⁄ ⁄ ⁄ Nominal Size (woofer) 6 x 9” 5 x 7” 6 2”6 2”5 4”5 4”4” (160mm) (165mm DIN) (130mm) (130mm DIN) (100mm) Recommended Amplifier Power 12–200 watts 12–160 watts 12–160 watts 12–160 watts 12–140 watts 12–140 watts 12–120 watts Nominal Impedance 4 ohms 4 ohms 4 ohms 4 ohms 4 ohms 4 ohms 4 ohms Frequency Response (±3dB, in-car) 35–20kHz 50–20kHz 55–20kHz 55–20kHz 58–20kHz 58–20kHz 85–20kHz 11 1 1 11 5 9 ⁄ ⁄ ⁄ ⁄ ⁄ ⁄ Mounting Cutout

Summary of the content on the page No. 3

Table of Contents Tools Required 2 Before You Begin 2 Planning the Installation 3 Speaker Wiring 4 Installing Speakers in Factory Cutouts 5 Installing Speakers in Nonstandard Locations 8 RX47/RX57/RX67 10 RX87/RX97 11 Professional Tips 12 Adding Subwoofers and Electronic Crossovers 13 Notice Installation of automotive stereo systems requires experience with a variety of mechanical and electrical procedures. This manual explains the installation flexibility of the Boston Rally Series coaxial spe

Summary of the content on the page No. 4

Tools Required Before You Begin These are the tools required Familiarize yourself with the location of fuel lines, hydraulic brake lines to complete the basic installa- and electrical wiring. Use extreme caution when cutting or drilling tion of the Boston Rally Series around these parts. components. Additional tools Shut off all stereo and other electrical devices before you start. are necessary for more cus- Protect the speakers by keeping them in their plastic bags until final tom work. instal

Summary of the content on the page No. 5

Planning the Installation Read all instructions carefully before you attempt any installation procedures. Make sure all operations are clear to you. Make sure you have adequate time and shelter to complete the installation. Many installations require multiple days to complete. Examine the Boston Rally Series speakers and hardware so that you are familiar with them before you start the installation. 1. Decide on speaker placement. 2. Run the speaker wires. 3. Install the speakers and complete th

Summary of the content on the page No. 6

Speaker Wiring For your convenience, two sets of two-conductor wire are provided to use between the speakers and the amplifier or head-unit. Other wire may be substituted if desired as long as it is at least 18 gauge. Two-conductor speaker wire connects the positive and negative ter- minals of each speaker to the corresponding positive and negative ter- minals on the amp or head-unit. One side of the wire will be marked in some way. Use the marked conductor to connect the positive terminals and

Summary of the content on the page No. 7

Installing Speakers in Factory Cutouts 1. Make sure the mounting surface provides a complete air seal between the front and the back of the speaker. If the surface is uneven, or if air can leak directly from the back of the speaker to the front, seal the air leaks with silicon sealant or weather stripping. Make sure that the sealing material does not touch any moving part of the speaker. 2. Attach the wires to the speaker. 3. Attach the assembly to the factory cutout using four of the supplied #

Summary of the content on the page No. 8

RX47 Notice The RX47 is supplied with the grille adapter ring attached to the metal basket of the speaker. For many factory cutouts, this adapter ring will have to be removed for installation. 1. Hold the speaker between both of your palms with the speaker cone facing you. Hook your fingers behind the magnet assembly. 2. Push one locking tab out and back with your thumbs to release it from the speaker frame (see diagram). Repeat this on all sides of the adapter until the adapter falls free. RX

Summary of the content on the page No. 9

RX87 and RX97 Installation Option The RX87 and RX97 can also be installed from underneath the rear deck to reduce the installed height of the tweeter module. A spacer is sup- plied with these speakers to protect the rubber surround. The spacer is installed between the speaker and the mounting surface as shown in the diagram. 7

Summary of the content on the page No. 10

Installing Speakers In Nonstandard Locations Check the clearance of both speaker locations. Your vehicle may not be symmetrical. (There may be multiple window controls on the driver’s side, for example.) If installing in the doors, remove the interior panel. Avoid possible speaker contact with door frames, handles and window tracks. Check the window clearance by rolling the window up and down. Also check for clearance with the door open and closed. The Boston Rally Series speakers are heavy, and

Summary of the content on the page No. 11

1. Trace the template onto the mounting panel. Mark the pilot hole, the edges of the large cutout and the locations of the screws. 2. Make sure that the mounting surface provides a complete air seal between the front and the back of the speaker. If the surface is uneven, or if air can leak directly from the back of the speaker to the front, seal the air leaks with silicon sealant or weather stripping. Make sure that the sealing material does not touch any moving part of the speaker. 9

Summary of the content on the page No. 12

RX47/RX57/RX67 1 3. Drill the pilot hole at the center of the cutout, then drill four /8” holes for the speaker’s mounting screws. Make the large circular cutout with a saber saw, hole saw or nibbler (depending on the material). 4. Slip “U”-clips over the screw holes. Position the flat side toward the speaker as shown in the diagram. 5. Attach the wires to the speaker. 6. Attach the assembly to the cutout as shown in the diagram. Use four of the supplied #8 x 1” sheet metal screws or other hardw

Summary of the content on the page No. 13

RX87/RX97 1 3. Drill four /4” holes for the speaker’s mounting screws. Make the large elliptical cutout with a saber saw or nibbler (depending on the material). 4. Attach the assembly to the cutout as shown in the diagram. Use the supplied machine screws and nuts or other hardware. Tighten the nuts just enough to seal the woofer against the mounting surface. Do not over- tighten the hardware. 5. Attach the wires to the speaker. 6. Attach the grille front. Snap the grille on to the grille frame f

Summary of the content on the page No. 14

Professional Tips • Some installers construct mounting surfaces from MDF. This dense material dampens resonances and provides a rigid mounting surface. • In cases where the speaker is being mounted on the surface of the interior door panel and there is a gap between the panel and the metal of the door, an appropriate thickness of MDF can be used as a spacer. • When mounting the speakers in nonstandard locations in the front of the car, try mounting them as high up and forward in the doors as

Summary of the content on the page No. 15

Adding Subwoofers and Electronic Crossovers The best way to combine a subwoofer with your Boston Rally Series speaker system is with an electronic crossover. Level matching (making the subwoofer play at the same level as the coaxial system) and precise frequency division are much easier to get right with an electronic crossover. Additionally, electronic crossovers have no insertion loss, and they isolate the coaxial speakers from the subwoofer’s back EMF. Subwoofer Crossover Frequency Recommenda

Summary of the content on the page No. 16

Limited Warranty For one year from the date of purchase, Boston Acoustics will repair for the original owner any defect in materials or workmanship that occurs in normal use, without charge for parts or labor. Your responsibilities are to use the speaker system according to the instructions supplied, to provide safe and secure transportation to the authorized Boston Acoustics service representative and to present proof of purchase in the form of your sales slip when requesting service. Excluded


Alternative user manuals
# User manual Category Download
1 Boston Acoustics Boston Loud CS23II User manual Speaker 3
2 Boston Acoustics Boston Loud CS225CIIBLACK User manual Speaker 1
3 Boston Acoustics Classic Series II CSSSUB10IIBLK User manual Speaker 5
4 Boston Acoustics BA 635 User manual Speaker 8
5 Boston Acoustics Boston Loud CS260IIBLACK User manual Speaker 0
6 Boston Acoustics Designer 261 User manual Speaker 2
7 Boston Acoustics CPS 12Wi User manual Speaker 5
8 Boston Acoustics Designer DSI460 User manual Speaker 2
9 Boston Acoustics Designer DSi465T2 User manual Speaker 0
10 Boston Acoustics CPS 10Wi User manual Speaker 1
11 Boston Acoustics GS110 User manual Speaker 6
12 Boston Acoustics FRB6R User manual Speaker 0
13 Boston Acoustics GS210 User manual Speaker 1
14 Boston Acoustics FRB5R User manual Speaker 0
15 Boston Acoustics Designer VRi560 User manual Speaker 2
16 Sony ACTIVE SUBWOOFER SA-W3800 User manual Speaker 5
17 Sony ACTIVE SUBWOOFER sa-w3000 User manual Speaker 9
18 Sony CR205 User manual Speaker 2
19 Sony CDP-C40 User manual Speaker 3
20 Sony DAV-JZ8888K User manual Speaker 14