Summary of the content on the page No. 1
ooooooooooooooooooooooooooooooooooooooooooooooooooooooooooooooooooooooooo
ooooooooooooooooooooooooooooooooooooooooooooooooooooooooooooooooooooooooo
CAD 120S
Stereo Power Amplifi er
NOTE: Before installing your new CAD 120S power amplifi er, please read this
manual carefully as it will inform you of the product specifi cations, proper
installation and correct operating procedures for your unit. Also included in
this manual are guidelines on how to service and care for your new Cary Audio
Design
Summary of the content on the page No. 2
TABLE OF CONTENTS Important Safety Instructions .............................................................. 2 Welcome Thank You ................................................................................................... 5 Product Features .......................................................................................... 6 Unpacking and Installation .......................................................................... 7 Specifications Specifications .
Summary of the content on the page No. 3
IMPORTANT SAFETY INSTRUCTIONS WARNING: To reduce the risk of fire or electric shock, do not expose this appliance to rain or moisture. The lightning flash with arrowhead symbol within an equilateral triangle is intended to alert the user to the presence of un-insulated dangerous voltage within the product’s enclosure that may be of sufficient magnitude to constitute a risk of electric shock to persons. CAUTION: To reduce the risk of electric shock, do not remove the cover. There are
Summary of the content on the page No. 4
IMPORTANT SAFETY INSTRUCTIONS 14. LIGHTNING: For added protection for the unit during a lightning storm, or when it is left unattended and unused for long periods of time, unplug it from the wall outlet and disconnect the antenna or cable system. This will prevent damage to the unit due to lightning and power line surges. 15. POWER LINES: An outside antenna system should not be located in the vicinity of overhead power lines or other electric light or power circuits, or where it can fa
Summary of the content on the page No. 5
IMPORTANT SAFETY INSTRUCTIONS 26. FCC INFORMATION FOR USER: CAUTION: ANY changes or modifications not expressly approved by the party responsible for compliance could void the user's authority to operate the equipment. NOTE: This equipment has been tested and found to comply with the limits for a Class B digital device pursuant to Part 15 of the FCC Rules. These limits are designed to provide reasonable protection against harmful interference in a residential installation. This eq
Summary of the content on the page No. 6
WELCOME THANK YOU Dear Cary Audio Customer: I am so pleased and excited about the Cary Audio Design CAD 120S stereo vacuum tube power amplifier. I have spent countless hours designing and refining this very special vacuum tube power amplifier. The CAD 120S started life in September of 2006 as a 60 watt ultra-linear push pull amplifier. Billy Wright, my business partner, was concerned that we needed more output power for difficult loudspeaker loads. At this time, I had just completed
Summary of the content on the page No. 7
WELCOME PRODUCT FEATURES The stereo vacuum tube power amplifier has a great history at Cary Audio Design. The previous generation Rocket 88 R and the V 12R power amplifiers garnered fantastic reviews for stable power output, incredible value for the money and sound quality along with ‘Best Buy’ and ‘Class A’ ratings from magazines and reviewers worldwide. Building on this storied legacy, we are releasing the CAD 120S stereo vacuum tube power amplifier. This innovative stereo power amp
Summary of the content on the page No. 8
WELCOME UNPACKING AND INSTALLATION This section describes the unpacking and installation procedures for your new component. Unpacking All Cary Audio Design shipping cartons have been specially designed to protect their contents and special care has been taken to prevent damage under normal shipping conditions. Mishandling should be evident upon inspection of the shipping container. If shipping damage is found after visual inspection, take care not to destroy the evidence. If necessa
Summary of the content on the page No. 9
SPECIFICATIONS Operating the CAD 120S is a simple procedure. It is designed for long term stability in virtually any home operating environment. However, if the unit is operated outside the parameters outlined in this owner's manual, damage may result. Please read this manual carefully before putting your new CAD 120S amplifier into operation. The following section describes the CAD 120S amplifiers’ basic specifications. The specifications are subject to change without notice or obliga
Summary of the content on the page No. 10
CONTROLS AND DISPLAYS FRONT PANEL 1. POWER • Press once to turn the power ON. • Press again to turn the power OFF. 2. LEFT CHANNEL BIAS • Indicates a proper DC current of between 130 to 150 ma. 3. RIGHT CHANNEL BIAS • Indicates a proper DC current of between 130 to 150 ma. 4. MODE • Press this button to change between Triode and Ultralinear modes. TOP PANEL The following illustration shows the tube placements on the CAD 120S. 9
Summary of the content on the page No. 11
CONTROLS AND DISPLAYS REAR PANEL 1. RIGHT CHANNEL OUTPUT – NEGATIVE LEAD 2. RIGHT CHANNEL OUTPUT – POSITIVE LEAD 3. RIGHT CHANNEL INPUT – XLR INPUT 4. RIGHT CHANNEL INPUT – RCA INPUT 5. TUBE FUSE ½ AMP FAST BLOW RIGHT CHANNEL 6. BIAS ADJUST POTENTIOMETER RIGHT CHANNEL 130 – 150 ma. 7. AC POWER MAIN FUSE 4 AMP SLOW BLOW 8. TUBE FUSE ½ AMP FAST BLOW LEFT CHANNEL 9. BIAS ADJUSTMENT POTENTIOMETER LEFT CHANNEL 130 – 150 ma. 10. LEFT CHANNEL INPUT – RCA INPUT
Summary of the content on the page No. 12
OPERATION Your new CAD 120S power amplifier is ready for operation after the speaker, interconnect cables and the vacuum tubes have been installed into their proper sockets. Refer to the labeling on the chassis for placement and proper tube installation. SPEAKER BINDING POSTS The CAD 120S will drive loudspeaker loads from as low as 2 ohms to a high of 16 ohms without any adjustment. Please remember to keep the proper phase on each channel when connecting the loudspeaker cables.
Summary of the content on the page No. 13
OPERATION cycle and power loads in the neighborhood change, the bias reading will fluctuate a bit. This is normal and therefore not critical. Another word about the meter readings. The louder you play the CAD 120S the more current it will draw. Playing loud, especially in the ultra-linear mode will peg the meters at 200 ma. This is normal and there is a protection circuit built into the metering circuit to prevent damage to the analog meters. Pegging the meters is fun! BREAK-IN
Summary of the content on the page No. 14
SERVICE AND CARE CARE AND CLEANING The cabinet housing and front panel of the CAD 120S may be cleaned with a soft cloth and Windex or a window cleaner. The frequency of cleaning will be governed by how many hours the CAD 120S is operated and by the cleanliness of the operating environment. FACTORY SERVICE Careful consideration has been given to the design of your CAD 120S to keep maintenance problems to a minimum. Any problems or requests for service should be referred to our C
Summary of the content on the page No. 15
UNITED STATES LIMITED WARRANTY Cary Audio Design warrants to the original United States purchaser for use in the United States that Cary Audio Design vacuum tube or solid state power amplifiers, surround sound processors or preamplifiers shall be free from defects in parts or workmanship for three (3) years from the date of the original purchase. Vacuum tubes, if any are used in the component, are offered a 90 day from purchase date exchange policy against defects with the exception of th
Summary of the content on the page No. 16
ooooooooooooooooooooo CARY AUDIO DESIGN 1020 Goodworth Drive, Apex, NC 27539 phone 919-355-0010 fax 919-355-0013 www.caryaudio.com ooooooooooooooooooooooooooooooooooooooooooooooooooooooooooooooooooooooooooooooooooooo
