Summary of the content on the page No. 1
DISTRIBUTION AMPLIFIERS
PRODUCT REVISION: 1
DA1912SX
1-IN, 2-OUT RGBS
DISTRIBUTION AMPLIFIER
USER’S GUIDE
MANUAL PART NUMBER: 400-0007-003
Summary of the content on the page No. 2
DISTRIBUTION AMPLIFIERS INTRODUCTION Page Thank you for purchasing Distribution Amplifier. We are sure you will find it a reliable and ............... 2 useful product. ................................ .......................... 2 Superior performance for the right price backed by ........ 2 solid technical and customer support is what we INSTALLATION ................................ .................. 2 have to offer. ................................ ......................... 2 The product you
Summary of the content on the page No. 3
DISTRIBUTION AMPLIFIERS mounted, to a table or wall, use only Altinex 1 made mounting accessories, such as mini Please read this manual carefully before using your mount-brackets ( ) and cables for Distribution Amplifier. Keep this manual optimum setup. handy for future reference. These safety • To turn off the main power, be sure to remove instructions are to ensure the long life of your the cord from power outlet. The power outlet DA1912SX and to prevent fire and shock hazard. socket should b
Summary of the content on the page No. 4
DISTRIBUTION AMPLIFIERS • Any changes or modifications to the unit not MECHANICAL expressly approved by Altinex, Inc. could void Width (inches) 4.56in (116mm) the user’s authority to operate the equipment. Height (inches) 3.50in (89mm) Depth (inches) 0.94in (24mm) 2 Weight (pounds) 0.6lbs (0.27kg) The Distribution Amplifier is designed Ship Weight (pounds) 2.0lbs (0.91kg) to allow the connection of one high resolution Material 0.1” Al RGsB or RGBS source to up two scan rate Finish Gray compatib
Summary of the content on the page No. 5
DISTRIBUTION AMPLIFIERS 4 4.3 SYNC LEVEL SWITCH The Sync Level Switch allows the DA1912SX to The Input Termination Switch is normally set to output a Sync Level of either 2V p-p or 4V p-p. the ON position and provides 75 Ohms This switch should normally be set in the 4V termination for the Red, Green, and Blue position. Some older display equipment may channels. By setting this switch in the OFF require a sync level of 2V in which case this switch position and using BNC "T" connectors, the input
Summary of the content on the page No. 6
DISTRIBUTION AMPLIFIERS 5 Step 5. If the image is l ess than perfect, check all the connections. The unit is very reliable 6 and seldom will be the cause of Step 1. Make sure that the proper p ower supply is malfunction. Poor quality cables may being used with the unit. The use of an often degrade the performance of the incorrect power supply can result in product. Make sure that the cables used equipment damage not covered by are coaxial cables and that all pins are in warranty. good condition
Summary of the content on the page No. 7
DISTRIBUTION AMPLIFIERS 7 8 The settings of the Distribution Model No. Description Amplifier can be adjusted using Input Termination, RACK MOUNTING BRACKETS Video Level, and Sync Level switches as described Rack/Wall/Furniture Mount Mini- in Section 4. There are no other adjustments brackets (2-"L" shaped brackets) necessary to operate the unit. The will operate successfully as long as cables are PS5502US 9V 500mA Power Supply for US attached properly and other technical specifications 9V 500m
Summary of the content on the page No. 8
DISTRIBUTION AMPLIFIERS 6 Why is the 9 be set to either the standard No: Question 0.7V output or to 1.0V 1 Compensation for cable loss important? output. When the switch is feet of cable is automatically made for set in the 1.0V output can I use distances up to100 feet position, this provides with the when set normally, though approximately a the can drive 35% increase in video signal when the signals through longer runs level. This can be used in depending on the source installations where cab
Summary of the content on the page No. 9
DISTRIBUTION AMPLIFIERS 11.2 RETURN POLICY TROUBLESHOOTING GUIDE 1 0 It is very important to Altinex that you receive the We have carefully tested and have found no products that you have ordered and that this problems in the supplied unit; however, product meets your expectations. In the unlikely we would like to offer the following suggestions : event, that an Altinex product needs to be • Please make sure that the input amplitude returned please follow the policies below: levels are as follo
