Summary of the content on the page No. 1
- II
- s
234 F A VENUE l C M , CA 92626
- 6500 l (800) 840 - 0288 l (714) 424 - 6510
l E -
© 2001, Channel Vision
Mail: sales@channelvision.com http://www.channelvision.com
FAX (714) 424
ESA OSTA ISCHER
cable.
be available at every TV hooked up to your coax
our television sets the new channels will "ahead of" y
additional inputs into your existing TV signal
Because the CVT Modulator merges these
g channels with your remote. switchin
achieve audio output. tape, or any ot
Summary of the content on the page No. 2
- - Channel Vision - CAUTION T With FCC Sta n- RISK OF ELECTRIC SHOCK ! DO NOT OPEN N part 15 of the FCC Rules. These limits are designed to in a residential installati installed and used in accordance with the t - • • Certification Requirements: Must be professional installing dealer, pass • certification test and familiar with TV and antenna systems. Call 800/840 - • 0288 for Channel Vision Training Manual and certificat ion test. Basic Installation Instructions The Ch
Summary of the content on the page No. 3
differences in signal strength may cause interference. CVT 3ub/uhf Basic Setup Source A/V Inputs That's all there is to it. The information on the following pages will setups. System Design Considerations sticated home "networks" involving many TV sets are feasible with the CVT Modulator, but care must be taken to design an optimum TV signal distribution system. TV sets are designed for signals around 10dBmV. Signals substantially below Channel Vision 0dBmV result in we MULTI RO
Summary of the content on the page No. 4
technical assistance. Calls before 8 a.m. and after 5 p.m. pacific standard time will be returned by the technician on call. Decrease signal strength (output dBmV) of modulator. Used to pass stereo to TV on non - stere S 75 Ω position is normal, 1K Ω position if using stereo loop. Modulator requires proper ventilation for long life reliability and Video Level Adjustment: base unit, let it cool down, install in band level. Use only to increase brightness and balance the well ven
Summary of the content on the page No. 5
modulated channels. Use a Y - Connector to combine the left and right If the modulated channels are good, use a low pass filter to audio before entering the modulator. - odulated. B) Herringbone in Picture on Modulated Chann el disconnecting the local channels, evaluate signal loss of r through the splitters and cable length of the C) ween modulator and the B) If the picture is snowy, use a #3102 - 78 low pass filter to combi
Summary of the content on the page No. 6
50' Large design 100' TV 3102 Filter application with 28.5dB minimal loss for 28.5dB 22.5dB the trunk line, CVT - 15PIA 22.5dB tap pulls part of 100' TV Filter the signal and attenuates a Basic design portion (6dB, MULTI ROOM VIDEO TECHNOLOGY 50' for home runs TV 9dB, 12dB, MULTI ROOM VIDEO TECHNOLOGY 50' TV TV TV TV TV TV Stereo Loop Kit w/ "Y" Connectors HS-2 and Cable Box Converter and use 3102 Filter HS-2 CVT - 15PIA CVT - 15PIA RF In HS-2 RF In HS-4 A/V In RF In A/V I
Summary of the content on the page No. 7
Due to the launch of digital CATV across the United States there is a need for clarific ation of digital CATV, which Channel offers a basic understanding of. Analog channels start from channel 2 to around the 70’s, digital may start around mid 80’s to as high as 115, some as high as 135. Exclude 95 to 99, (the old FM band now used for pay - perview or other programming). Compression of channels will vary in ratio, one cable company may use 8 to 1 ratio, com pr
Summary of the content on the page No. 8
HS-2 HS-2 CH 85 CH 123/125 Cable Box DIGITAL HS-2 HS-8 HS-2 CVT - 15PIA CVT 1UB/UHF-II 3102 Filter FRONT OF THE CATV SYSTEMS Antenna A/V SOURCES PART#3205 ALSO IS PLACED AT THE Cable or max 750MHz COAX /CATV SYSTEMS DIGITAL CATV/1- RG-6 FILTER USED WITH DIAGRAM#C 3102-118 LOW PASS Cable Box DIGITAL Cable Box DIGITAL HS-8 70 A/V-OUT TO TV CH 2 TO INPUT AT TV ANALOG HS-2 Cable Box HS-8 BE USED IF NO VIDEO COMBINER KIT CAN DIGITAL 3101 CABLE BOX CH 74-76 HS-2 CVT
Summary of the content on the page No. 9
Channel Vision Technology will repair or replace any defect in material or workmanship which o ccur during normal use of this product with new or rebuilt parts, free of charge in the USA, for two years from the date of original purchase. This is a no hassle warranty with no mail in warranty card needed. This warranty does not cover damages in shipment, failures caused by other products not supplied by Channel Vision Technology, or failures due to accident, misuse, abus e, or alteration o
