Summary of the content on the page No. 1
14472 102808
Summary of the content on the page No. 2
ii QUICK START GUIDE - AVR 707 & AVR 705 © 2008 B&K Components Ltd. All rights reserved. The information in this manual is copyright protected. No part of this manual may be copied or reproduced in any form without prior written consent from B&K Components, Ltd. B&K Components Ltd. SHALL NOT BE LIABLE FOR OPERATIONAL, TECHNICAL OR EDITORIAL ERRORS/OMISSIONS MADE IN THIS MANUAL. The information in this manual may be subject to change without prior notice. Accessories Included 1 - SR10.1 Remote Co
Summary of the content on the page No. 3
1 Table of Contents FRONT AND REAR PANEL ...............................................................................................2 CONNECTION OVERVIEW ...............................................................................................4 VIDEO INPUT / OUTPUT CONNECTIONS .......................................................................5 Video Input Connection - HDMI...............................................................................5 Video Input Connection - Comp
Summary of the content on the page No. 4
2 FRONT AND REAR PANEL 1 2 3 4 6 5 7 8 9 10 11 12 13 15 14 22 24 23 16 21 20 19 18 17 1 Left Hand Knob - The left selector knob is a rotary encoder with the primary purpose of A/V input source selection. The knob serves multiple functions. Pushing in on the the knob will scroll through the options to control or select Input Source, AM/FM Tuning, AM/FM Station, Audio Preference or Video Preference. Rotating the knob will change the highlighted function. 2 Display - The receiver contains a 16 char
Summary of the content on the page No. 5
3 FRONT AND REAR PANEL 6 Headphone Jack - Headphones having a standard 1/4” stereo plug may be connected to the headphone output. 7 Control Output - 1/8” Mono Mini-jack (Tip+ Ring -) source of 12VDC 100mA output for controlling external devices, such as ampli- fiers and projection screens. A remote control CTRL+ "Control On" command will turn on 12VDC and “CTRL-” will turn off 12VDC. Additional control and control is available using RS-232 and Ethernet BKC-DIP. Amp Enable - 1/8” Mono Mini-jack (
Summary of the content on the page No. 6
4 CONNECTION OVERVIEW The following is an overview of connections found on the AVR 707. Further information may be found later in the quick guide or in the AVR 707 manual. This guide should only be used as a reference starting point, it is recommended you contact an authorized B&K installer or dealer for inte- gration of the receiver in advanced installations.
Summary of the content on the page No. 7
5 VIDEO INPUT / OUTPUT CONNECTIONS Composite Source S-Video Source Component Source HDMI Source Video Input Connection - HDMI The B&K surround receiver provides 6 HDMI A/V inputs. HDMI carries both audio and video, B&K allows options to process audio and video separately (please see the menu setup for further options). To connect an HDMI video source to the B&K, connect the HDMI cable to the HDMI output on the source piece. Then connect the other end of the cable into the corresponding HDMI inpu
Summary of the content on the page No. 8
6 AUDIO INPUT CONNECTIONS Analog Source Coaxial Digital Source Optical Digital Source HDMI Source Audio Input Connection - HDMI Although HDMI connection carries both audio and video, B&K can process audio and video separate- ly (please see the menu structure for further information). To connect an HDMI audio source to the B&K, connect the HDMI cable to the HDMI output on the source device. Then connect the other end of the cable into the corresponding HDMI input on the receiver. Multichannel PCM
Summary of the content on the page No. 9
7 AUDIO OUTPUT CONNECTIONS Audio Output Connection The AVR 707 and 705 receivers support 7.1 RCA surround outputs. Typical usage is for use with other external amplifiers. These outputs may be used to connect external amplifiers and/or a subwoofer to the receiver. Be sure to match the appropriate pre-amp output to the speakers location in the room. For example, connect the center channel output the the center speaker amplifier channel. For use in a five channel audio system, do not connect the s
Summary of the content on the page No. 10
8 CONFIGURATION AND CONTROL There are a few different ways to achieve control and configuration of the AVR 707. Using the compo- nent video or HDMI output on the AVR 707 you may use the on-screen GUI navigation while viewing changes on the HD monitor. BKC-DIP communication support is available for use with Ethernet and RS-232 from and external controller or device or a PC. Some restrictions may apply. Please see the full manual or the B&K website for further information. GUI On-Screen Overlay In
Summary of the content on the page No. 11
9 SAFETY PRECAUTIONS Installation Considerations CAUTION R IS K OF E L ECT RIC S HOCK DO N OT O P EN WARNING: to prevent fire or shock hazard, do not expose this unit to rain or moisture. Care should be taken to prevent objects or liquid from entering the enclosure. Never handle the power cord with wet hands. • The lightning flash with arrowhead within a triangle is intended to alert the user of the presence of uninsulated "dangerous voltage" within the product's enclosure that may constitu
Summary of the content on the page No. 12
SPECIFICATIONS Specification AVR 707 AVR 705 Receiver Surround Outputs 7.1 RCA Type Dolby Digital / Dolby Pro Logic IIx / Dolby Digital Surround-EX Surround Sound Processing DTS / DTS-ES Discrete / NEO:6 Frequency Response 20 Hz - 20kHz Total Harmonic Distortion THD (S + N) 0.09 % 20 - 20 kHz Surround Processor Type Freescale DSP 56371 (upgradable) Input Sensitivity 90 mV Signal to Noise Ratio 92 dB unbalanced / 98 dB balanced Input Impedance 10 kΩ Output Impedance 221 Ω Maximum Output Level 3V
