Summary of the content on the page No. 1
LCD PROJECTOR LENS
MODEL NO. LNS-S03
LENS REPLACEMENT
AND INSTALLATION PROCEDURES
NOTES ON REPLACEMENT AND INSTALLATION
The procedures and the needed pars for lens installation depend on the type of
cabinet. Before installing or replacing the lens, make sure the type of cabinet and be
sure to refer to the Installations corresponding with your projector.
When installing or replacing the lens, make sure the Lens Model No. matches with
your projector. Refer to the catalog, or contact your sales
Summary of the content on the page No. 2
NOTES ON LENS INSTALLATION • Lens installation and replacement should be made by the qualified service per- sonnel. • Be sure to install the lens following this procedure precisely. • The lens cover is on the lens for protection. Be sure to replace the lens cover before installation. • When installing or replacing the lens, be careful not to stain, scratch or damage the lens. LIST OF CONTENTS Following parts are included in the packing. • LENS 1 pc. • DRIVER 1 pc. BE SURE TO CHECK FOR SAFETY Af
Summary of the content on the page No. 3
LENS REPLACEMENT AND INSTALLATION PROCEDURE {Type (1) Cabinet} Remove Lower Lens Cover. Remove 2 Screws A. B 1 Push part B and pull Lower Lens Cover down. (See Fig. 1.) A LOWER LENS COVER Fig-1 C Remove 4 Screws C. Pull Upper Lens Cover 2 toward front and remove. (See Fig. 2.) UPPER LENS COVER C Fig-2 UPPER LENS COVER Remove 2 Scres D and Cover Plate on the back of 3 Upper Lens Cover. (See Fig. 3.) COVER PLATE D Fig-3 -2-
Summary of the content on the page No. 4
Replace Lens Cap on the rear (mounting side) of Projection Lens and mount the lens on Lens 4 Mouting Bracket with 4 Screws. To mount the lens with Lens Motor on the right. (See Fig. 4.) GUIDE PIN LENS MOUNTING BLACKET LOCATE MOTOR ON RIGHT SIDE DRIVER IN THE LENS Fig-4 Part No. (610 275 6029) Connect Lens Motor Lead to the connector 5 "K96T" on the circuit board under the lens. K96T CON- NECTOR LENS MOTOR LEAD Fig-5 -3-
Summary of the content on the page No. 5
Use a Light-Block Sheet (provided with projector) corresponding with lens. (Refer to the Type No. 6 below.) Set Light-Block Sheet through the lens. Make sure the shape of Light-Block Sheet and be sure to set them as shown in the Fig. 6. NOTE: ● Be sure to set a Light-Block Sheet as shown in Fig-6. ● Make sure the mark (TOP and BACK) on Light-Block Sheet and set them properly. Use light-block sheet Type No. TYPE FD1 (PART No. 610 290 9258) Fig-6 LIGHT BLOCK SHEET Make sure the sheet fig
Summary of the content on the page No. 6
Replace Upper Lens Cover. Slide Light-Block Sheet into the guide of Upper Lens Cover and set 7 them in front of the flap. (See Fig. 7.) Fix Upper Lens Cover with 4 Screws C. (See Fig. 2.) Replace Lower Lens Cover. Slide Light-Block Sheet into the guide of Lower Lens Cover and set 8 them in front of the flap. (See Fig. 7.) Fix Lower Lens Cover with 2 Screws A. (See Fig. 1.) Turn the projector on and operate Lens shift, Zoom and Focus fully to check Light-Block Sheet. If 9 Light-Block Sheet in
Summary of the content on the page No. 7
LENS REPLACEMENT AND INSTALLATION PROCEDURE {Type (2) Cabinet} A Remove Lens Cover. Remove 2 Screws A. Push 1 part B and pull Upper Lens Cover up. (See Fig. 1.) UPPER LENS COVER B Fig-1 C Remove 4 Screws C. Pull Lower Lens Cover 2 toward front and remove. (See Fig. 2.) LOWER LENS COVER C Fig-2 D Remove 2 Screws D and Cover Plate on the 3 back of Upper Lens Cover. (See Fig. 3.) UPPER LENS COVER COVER PLATE Fig-3 -6-
Summary of the content on the page No. 8
Replace Lens Cap on the rear (mounting side) of Projection Lens and mount the lens on Lens 4 Mouting Bracket with 4 Screws. To mount the lens with Lens Motor on the right. (See Fig. 4.) GUIDE PIN LENS MOUNTING BLACKET DRIVER LOCATE MOTOR IN THE LENS ON RIGHT SIDE Part No. (610 275 6029) Fig-4 Connect Lens Motor Lead to the connector 5 "K96T" on the circuit board under the lens. Fix Lens Motor Lead with the lead holder on the cir- cuit board. LEAD HOLDER K96T LENS MOTOR LEAD Fig-5 CONNECTOR -7-
Summary of the content on the page No. 9
Use 2 Light-Block Sheets (provided with projector) corresponding with lens. (Refer to the Type No. 6 below.) Set 2 Light-Block Sheets through the lens. Make sure the shape of Light-Block Sheets and be sure to set them as shown in the Fig. 6. NOTE: ● Be sure to set each Light-Block Sheets as shown in Fig-6. ● Make sure the mark (TOP and BACK) on Light-Block Sheets and set them properly. Use light-block sheets Type No. TYPE FC1 (PART No. 610 284 2500) TYPE FC2 (PART No. 610 284 2494) Fig
Summary of the content on the page No. 10
Replace Lower Lens Cover. Slide Light-Block Sheets into the guide of Lower Lens Cover and set 7 them in front of the flap. (See Fig. 7.) Fix Lower Lens Cover with 4 Screws C. (See Fig. 2.) Replace Upper Lens Cover. Slide Light-Block Sheets into the guide of Upper Lens Cover and set 8 them in front of the flap. (See Fig. 7.) Fix Upper Lens Cover with 2 Screws A. (See Fig. 1.) Turn the projector on and operate Lens shift, Zoom and Focus fully to check Light-Block Sheets. If 9 Light-Block Sheet
