ADTX ZRW113 user manual

User manual for the device ADTX ZRW113

Device: ADTX ZRW113
Size: 0,67 MB
Date of adding : 2014-09-22 15:36:23
Number of pages: 4
Print the manual

Download

How to use this site?

Our goal is to provide you with a quick access to the content of the user manual for ADTX ZRW113. Using the online preview, you can quickly view the contents and go to the page where you will find the solution to your problem with ADTX ZRW113.

For your convenience

If looking through the ADTX ZRW113 user manual directly on this website is not convenient for you, there are two possible solutions:

  • Full Screen Viewing - to easily view the user manual (without downloading it to your computer), you can use full-screen viewing mode. To start viewing the user manualADTX ZRW113 on full screen, use the buttonFullscreen.
  • Downloading to your computer - You can also download the user manual ADTX ZRW113 to your computer and keep it in your files. However, if you do not want to take up too much of your disk space, you can always download it in the future from ManualsBase.
ADTX ZRW113 user manual
Advertisement
« Page 1 of 4 »
Advertisement
Print version

Many people prefer to read the documents not on the screen, but in the printed version. The option to print the manual has also been provided, and you can use it by clicking the link above - Print the manual. You do not have to print the entire manual ADTX ZRW113 but the selected pages only. paper.

Summaries

Below you will find previews of the content of the user manuals presented on the following pages to ADTX ZRW113. If you want to quickly view the content of pages found on the following pages of the manual, you can use them.

Abstracts of contents
Summary of the content on the page No. 1

ZRW113
HomePro
Z-Wave Radio Frequency (RF) Controlled, 120 VAC,
RF Home Automation
Isolated Contact Wall Mounted 3-Way Switch,
Series 200, Release 2.2
Shown with supplied
TM
Decora trim plate
Note: This module must be “Included in the Network” only
where it will be permanently installed. The proper operation
of this node in the mesh network is dependent on it knowing its
location with respect to other nodes. You cannot “test bench”
configure this module, then install.
ZRW113 WALL MOUNTED SWI

Summary of the content on the page No. 2

INCLUDING ZRW113 TO THE NETWORK STEP 1.. Prepare the Controller to include a unit to the network by adding it to a group (method of adding a node to the network). Refer to controller instructions. STEP 2. The ZRW113 must be in its permanently installed location. Tap either the top or bottom of the ZRW113 once. STEP 3. You should see an indication on your Controller that the “DEVICE WAS INCLUDED” in the network. NOTE: If you have trouble adding the ZRW113 to a group it may be that the

Summary of the content on the page No. 3

Association The ZRW113 supports the Association command. The ZRW113 can be set to control other Z-Wave devices. You can turn on and off, and even dim other Z-Wave devices once they are “associated” into either of 2 groups of the ZRW113. Each group is turned on, off or dimmed by tapping or holding the switch a differing amount of times. If you associate Z-Wave devices into Group 2, you can turn those devices on and off by tapping the switch on or off twice. You can brighten or dim devices by tap

Summary of the content on the page No. 4

SUC Support There must be a Static Update Controller in your Z-Wave system for this feature to work. The Static Controller can act as a gateway in the system, since other nodes always know its position (not moved after addition to the network. The “always listening” advantage of the Static Controller is that other nodes can transmit information frames to it whenever needed. You can assign an “SUC Route” to the ZRW113. Refer to your controller’s instructions on how to do this (if it supports it)


Similar user manuals
# User manual Category Download
1 Sony BZPS-8001 Switch 37
2 Sony DFS-700P Switch 122
3 Sony DVS-9000 Switch 14
4 Sony DVS-9000SF Switch 28
5 Sony DFS-700 Switch 181