Campbell Manufacturing SDM-SW8A user manual

User manual for the device Campbell Manufacturing SDM-SW8A

Device: Campbell Manufacturing SDM-SW8A
Category: Switch
Manufacturer: Campbell Manufacturing
Size: 0.4 MB
Added : 2/18/2014
Number of pages: 26
Print the manual

Download

How to use this site?

Our goal is to provide you with a quick access to the content of the user manual for Campbell Manufacturing SDM-SW8A. Using the online preview, you can quickly view the contents and go to the page where you will find the solution to your problem with Campbell Manufacturing SDM-SW8A.

For your convenience

If looking through the Campbell Manufacturing SDM-SW8A user manual directly on this website is not convenient for you, there are two possible solutions:

  • Full Screen Viewing - to easily view the user manual (without downloading it to your computer), you can use full-screen viewing mode. To start viewing the user manual Campbell Manufacturing SDM-SW8A on full screen, use the button Fullscreen.
  • Downloading to your computer - You can also download the user manual Campbell Manufacturing SDM-SW8A to your computer and keep it in your files. However, if you do not want to take up too much of your disk space, you can always download it in the future from ManualsBase.
Campbell Manufacturing SDM-SW8A User manual - Online PDF
Advertisement
« Page 1 of 26 »
Advertisement
Print version

Many people prefer to read the documents not on the screen, but in the printed version. The option to print the manual has also been provided, and you can use it by clicking the link above - Print the manual. You do not have to print the entire manual Campbell Manufacturing SDM-SW8A but the selected pages only. paper.

Summaries

Below you will find previews of the content of the user manuals presented on the following pages to Campbell Manufacturing SDM-SW8A. If you want to quickly view the content of pages found on the following pages of the manual, you can use them.

Abstracts of contents
Summary of the content on the page No. 1


SDM-SW8A 8 Channel
Switch Closure Module
Revision: 7/07
Copy right © 1987-2007
Campb e ll Scienti f i c , In c.

Summary of the content on the page No. 2

Warranty and Assistance The SDM-SW8A SWITCH CLOSURE INPUT MODULE is warranted by CAMPBELL SCIENTIFIC, INC. to be free from defects in materials and workmanship under normal use and service for twelve (12) months from date of shipment unless specified otherwise. Batteries have no warranty. CAMPBELL SCIENTIFIC, INC.'s obligation under this warranty is limited to repairing or replacing (at CAMPBELL SCIENTIFIC, INC.'s option) defective products. The customer shall assume all costs of remov

Summary of the content on the page No. 3

SDM-SW8A Table of Contents PDF viewers note: These page numbers refer to the printed version of this document. Use the Adobe Acrobat® bookmarks tab for links to specific sections. 1. Function........................................................................1 2. Specifications ..............................................................2 3. Power Supply Considerations....................................3 4. Connections...........................................................

Summary of the content on the page No. 4

SDM-SW8A Table of Contents List of Tables 1. Datalogger to SDM-SW8A Connections................................................... 2 2. SDM-SW8A to SDM-SW8A Connections................................................ 3 3. Address Jumpers ........................................................................................ 5 4. Measurement Jumpers................................................................................ 6 5. Instruction 102 – SDM-SW8A .........................

Summary of the content on the page No. 5

SDM-SW8A Switch Closure Input Module 1. Function The 8 channel SDM-SW8A Switch Closure Input Module (see Figure 1) measures up to 8 channels of switch closure or voltage pulse inputs. Each channel may be configured to read single-pole double-throw (SPDT) switch closure, single-pole single-throw (SPST) switch closure, or voltage pulse. Output options include counts, duty cycle, and state. The SW8A is addressed by the datalogger, allowing multiple SW8As to be connected to one datalogge

Summary of the content on the page No. 6

SDM-SW8A Switch Closure Input Module 2. Specifications Operating voltage: 12 VDC nominal (9.6 to 16) Current drain: 3 mA quiescent, 6 mA active (max) o Environmental: -25 to +50 C, 0 to 90% RH, noncondensing Measurement types: Switch closure (SPDT, SPST) DC voltage pulse Input voltage threshold: From below 0.9 to above 4.0 VDC,±20 VDC max Maximum input frequency: 100 Hz (50% duty cycle) Minimum input pulse width: 5 ms high, 5 ms low Maximum bounce time: 3 ms open without counting O

Summary of the content on the page No. 7

SDM-SW8A Switch Closure Input Module TABLE 2. SDM-SW8A to SDM-SW8A Connections SDM-SW8A that’s connected to a CR10(X), CR800, CR850, CR1000, CR23X, CR3000, SDM-SW8A that’s SDM-SW8A CR5000, or CR7 connected to a 21X +12 12 V +12 C3 C3 C3 C2 C2 C2 C1 IN C1 IN C1 IN C1 OUT not used (see Note 2) C1 OUT (see Note 3) Notes: (1) If using an auxiliary power supply, instead of connecting the datalogger’s 12 V or +12 terminal to the SW8A, connect the power supply’s positive

Summary of the content on the page No. 8

SDM-SW8A Switch Closure Input Module 4. Connections All connections to the datalogger, power supply, and other SW8As are made from terminals located under "TO DATALOGGER" on the SW8A (refer to Figure 1). Sensor connections are made at the remaining terminals. 4.1 Connections to Dataloggers and Other SW8As Connections between an SW8A and the CR10 and 21X dataloggers are shown in Table 1. Connections to multiple SW8As are shown in Table 2. 1. The order in which connections are made

Summary of the content on the page No. 9

SDM-SW8A Switch Closure Input Module TABLE 3. Address Jumpers Pins Address 1-8 2-7 3-6 4-5 00 c c c c 01 c c c nc 02 c c nc c 03 c c nc nc 10 c nc c c 11 c nc c nc 12 c nc nc c 13 c nc nc nc 20 nc c c c 21 nc c c nc 22 nc c nc c 23 nc c nc nc 30 nc nc c c 31 nc nc c nc 32 nc nc nc c 33 nc nc nc nc c = connected nc = not connected FIGURE 2. SDM-SW8A Address and Port Configuration Jumpers with Sensor Wiring Examples 5

Summary of the content on the page No. 10

SDM-SW8A Switch Closure Input Module 5.2 Measurement Jumpers Near each input channel is a jumper triplet used to configure the channel for the measurement type. The SDM-SW8A is shipped from the factory with each channel configured for DC Voltage pulse. An example of each configuration is illustrated in Figure 2. Table 4 shows jumper pins and the corresponding measurement type. TABLE 4. Measurement Jumpers Measurement Type Pins Jumpered SPDT Switch Closure 1 and 6 SPST Switch Cl.

Summary of the content on the page No. 11

SDM-SW8A Switch Closure Input Module Parameter Enter & Data Type FunctOp The FunctOp is used to determine the result that will be returned by the Constant SW8A. Numeric Function Code 0 Returns the state of the signal at the time the instruction is executed. A 0 is stored for low and a 1 is stored for high. 1 Returns the duty cycle of the signal. The result is the percentage of time the signal is high during the scan interval. 2 Returns a count of the number of positive transi

Summary of the content on the page No. 12

SDM-SW8A Switch Closure Input Module NOTE Instruction 102 is not contained in all CR10 or 21X PROMS. To verify that the datalogger contains the Instruction, enter 102 into a datalogger Programming Table. If the Instruction is accepted, the PROM contains the Instruction. Repetitions (Reps, Parameter 1) specifies the number of SW8A channels to read. Parameter 2 is the address of the first SW8A. If more Reps are requested than exist in one module, the datalogger automatically increment

Summary of the content on the page No. 13

SDM-SW8A Switch Closure Input Module 7. Datalogger Program Details 7.1 Datalogger Scan Rate The Module samples channel state every 2 ms and accumulates the information for duty cycle and counts. Each channel has one 16 bit accumulator for duty cycle and one for counts. The accumulators are reset when the datalogger requests information from the SW8A and when the count exceeds 65535. The datalogger scan rate must be frequent enough to avoid SW8A accumulator overflow. Each Duty Cycle

Summary of the content on the page No. 14

SDM-SW8A Switch Closure Input Module forces a watchdog reset by addressing the Module and requesting sufficient information to cause a minimum of 65 clock line transitions. Advantages to the trapping routine are: • The bombed processor is detected before erroneous values (-99999) are included in subsequent processing. • The processor may be reset sooner. • The time of processor failure may be logged by the datalogger. • Number of failures may be logged. A trapping routine, as described

Summary of the content on the page No. 15

SDM-SW8A Switch Closure Input Module 8.2 SPST Switch Closure Single-pole single-throw switches are either open (high state) or connected to ground (low state). Typical SPST switches include contact closure (reed switch) anemometers, tipping bucket rain gauges, and open collectors (semiconductor switches). Many control devices utilize open collectors and provide terminals for monitoring the switch. For all SW8A measurements, the 100 Hz maximum input frequency and 5 ms pulse width sp

Summary of the content on the page No. 16

SDM-SW8A Switch Closure Input Module 50% Duty Cycle - The "worst case" duty cycle measurement error for a 50% duty cycle at a given input frequency is ±ERROR = Hz * 0.4 where ERROR = Actual Duty Cycle ±Measured Duty Cycle. For example, a 50% duty cycle at 10 Hz could be measured as 46% to 54% in the worst case. Minimum/Maximum - The measurable minimum/maximum duty cycle is defined by the 5 ms pulse width specification of the SW8A. For example, at a 10 Hz frequency, the minimum and max

Summary of the content on the page No. 17

SDM-SW8A Switch Closure Input Module addressed SW8A is present. The 21X works similarly, except the data from the SW8A is input to single ended analog channel 1, not C1. Depending on the Command, Reps, and Channel information, the module will shift out one or more bytes to the datalogger, again using C2 as a clock driven by the datalogger. The module shifts out each bit on the falling edge of the clock; the datalogger reads each bit on the rising edge of the clock. Each time an ent

Summary of the content on the page No. 18

SDM-SW8A Switch Closure Input Module This is a blank page. 14

Summary of the content on the page No. 19

Appendix A. Program Example The Edlog program is an example only and is not meant to be used verbatim. In application, the concepts illustrated here are likely to be only fragments of a larger program. The example program reads all 8 ports of an SW8A which is set to address 00. It is read three times per scan, once each for State, Duty Cycle, and Count information. The scan rate is fixed at 1 second, with a 5 minute output of State, average Duty Cycle, and average Count. To prevent e

Summary of the content on the page No. 20

Appendix A. Program Example FIGURE A-1. Example Program Flow Chart PROGRAM EXAMPLE Input Locations Used: 1:STATE #1 13:DUTY #5 2:STATE #2 14:DUTY #6 3:STATE #3 15:DUTY #7 4:STATE #4 16:DUTY #8 5:STATE #5 17:COUNT#1 6:STATE #6 18:COUNT #2 7:STATE #7 19:COUNT #3 8:STATE #8 20:COUNT #4 9:DUTY #1 21:COUNT #5 10:DUTY #2 22:COUNT #6 11:DUTY #3 23:COUNT #7 12:DUTY #4 24:COUNT #8 25:RESET CNT Output Arrays: ID = 105, 27 ELEMENTS ID = 112, 4 ELEMENTS


Alternative user manuals
# User manual Category Download
1 Sony 4-296-436-11 (2) User manual Switch 0
2 3Com 10/100BASE-TX User manual Switch 61
3 3Com 2226-SFP User manual Switch 688
4 3Com 16985ua.bk User manual Switch 10
5 3Com 10BASE-T User manual Switch 4
6 3Com 10BASE-2 User manual Switch 1
7 3Com 1000BASE User manual Switch 6
8 3Com 2226 PLUS User manual Switch 473
9 3Com 2250-SFP User manual Switch 538
10 3Com 1600 User manual Switch 0
11 3Com 2924-PWR User manual Switch 72
12 Sony BZPS-8001 User manual Switch 1
13 Sony DFS-700P User manual Switch 123
14 Sony DVS-9000 User manual Switch 9
15 Sony DVS-9000SF User manual Switch 5