Summary of the content on the page No. 1
DES-1016D
10/100 NWay Ethernet/
Fast Ethernet Switch
User’s Guide
First Edition (Sept., 1999)
6DES1016D.02
Printed In Taiwan
RECYCLABLE
Summary of the content on the page No. 2
Wichtige Sicherheitshinweise 1. Bitte lesen Sie sich diese Hinweise sorgfältig durch. 2. Heben Sie diese Anleitung für den spätern Gebrauch auf. 3. Vor jedem Reinigen ist das Gerät vom Stromnetz zu trennen. Vervenden Sie keine Flüssig- oder Aerosolreiniger. Am besten dient ein angefeuchtetes Tuch zur Reinigung. 4. Um eine Beschädigung des Gerätes zu vermeiden sollten Sie nur Zubehörteile verwenden, die vom Hersteller zugelassen sind. 5. Das Gerät is vor Feuchtigkeit zu schützen. 6. Bei der A
Summary of the content on the page No. 3
Limited Warranty Hardware: D-Link warrants each of its hardware products to be free from defects in workmanship and materials under normal use and service for a period commencing on the date of purchase from D-Link or its Authorized Reseller and extending for the length of time stipulated by the Authorized Reseller or D-Link Branch Office nearest to the place of purchase. This Warranty applies on the condition that the product Registration Card is filled out and returned to a D-Link office withi
Summary of the content on the page No. 4
warrants the magnetic media, on which D-Link provides its software product, against failure during the same warranty period. This warranty applies to purchased software, and to replacement software provided by D-Link pursuant to this warranty, but shall not apply to any update or replacement which may be provided for download via the Internet, or to any update which may otherwise be provided free of charge. D-Link's sole obligation under this software warranty shall be to replace any defective
Summary of the content on the page No. 5
LIMITATION OF WARRANTIES IF THE D-LINK PRODUCT DOES NOT OPERATE AS WARRANTED ABOVE, THE CUSTOMER'S SOLE REMEDY SHALL BE, AT D-LINK'S OPTION, REPAIR OR REPLACEMENT. THE FOREGOING WARRANTIES AND REMEDIES ARE EXCLUSIVE AND ARE IN LIEU OF ALL OTHER WARRANTIES, EXPRESSED OR IMPLIED, EITHER IN FACT OR BY OPERATION OF LAW, STATUTORY OR OTHERWISE, INCLUDING WARRANTIES OF MERCHANTABILITY AND FITNESS FOR A PARTICULAR PURPOSE. D-LINK NEITHER ASSUMES NOR AUTHORIZES ANY OTHER PERSON TO ASSUME FOR IT ANY OTHE
Summary of the content on the page No. 6
Trademarks Copyright 1999 D-Link Corporation. Contents subject to change without prior notice. D-Link is a registered trademark of D-Link Corporation/D-Link Systems, Inc. All other trademarks belong to their respective proprietors. Copyright Statement No part of this publication may be reproduced in any form or by any means or used to make any derivative such as translation, transformation, or adaptation without permission from D-Link Corporation/D-Link Systems Inc., as stipulated by the Uni
Summary of the content on the page No. 7
TABLE OF CONTENTS 0 ABOUT THIS GUIDE ......................................................................... IX PURPOSE ......................................................................................................IX TERMS/USAGE .............................................................................................IX OVERVIEW OF THIS USER’S GUIDE ...............................................................IX 1 INTRODUCTION ......................................................
Summary of the content on the page No. 8
5 TECHNICAL SPECIFICATIONS ......................................................15 6 RJ-45 PIN SPECIFICATION ..............................................................18
Summary of the content on the page No. 9
10/100 NWay Ethernet/Fast Ethernet Switch User’s Guide 0 ABOUT THIS GUIDE Congratulations on your purchase of the 10/100 NWay Ethernet/Fast Ethernet Switch. This device integrates 100Mbps Fast Ethernet and 10Mbps Ethernet network capabilities in a highly flexible package. Purpose The purpose of this manual is to discuss the installation and use of your 16-port 10/100Mbps NWay Ethernet/Fast Ethernet Switch. Terms/Usage For simplicity, this documentation uses the term “Switch” (first letter upper
Summary of the content on the page No. 10
10/100 NWay Ethernet/Fast Ethernet Switch User’s Guide Chapter 2, “ .” Helps you get started ♦ Unpacking and Setup with the basic installation of the Switch. ♦ Chapter 3, “Identifying External Components.” Describes the front panel, rear panel, and LED indicators of the Switch. ♦ Chapter 4, “Connecting the Switch.” Tells how you can connect the Switch to your Ethernet network. ♦ Appendix A, “Technical Specifications.” Lists the technical (general, physical and environmental, and performance) sp
Summary of the content on the page No. 11
10/100 NWay Ethernet/Fast Ethernet Switch User’s Guide 1 1 INTRODUCTION This section describes the features of the Switch. Features The Switch is designed for easy installation, a superior cost/performance ratio, and easy migration to a bandwidth-critical environment where traffic on the network and the number of users increases continuously. The Switch supports auto-negotiation, allowing both 10Mbps and 100Mbps operation in full-duplex or half-duplex mode, even on all ports simultaneously. Low
Summary of the content on the page No. 12
10/100 NWay Ethernet/Fast Ethernet Switch User’s Guide Performance features ♦ Sixteen high-performance 10/100Mbps NWay ports; all ports can auto-negotiate for full- or half-duplex operation ♦ Uplink (MDI-II) port for straight-through connection to another switch, hub or repeater ♦ Full wire-speed forwarding for 100Mbps Fast Ethernet (148,800 pps) and 10Mbps Ethernet (14,880 pps) on all ports ♦ High-performance 2M SGRAM packet buffer ♦ Up to 8K MAC address table ♦ IEEE 802.3x-compliant flow contr
Summary of the content on the page No. 13
10/100 NWay Ethernet/Fast Ethernet Switch User’s Guide 2 2 UNPACKING AND SETUP This chapter provides unpacking and setup information for the Switch. Unpacking Open the shipping carton of the Switch and carefully unpack its contents. The carton should contain the following items: ♦ One 10/100 NWay Ethernet/Fast Ethernet Switch ♦ One AC power cord ♦ This User’s Guide ♦ Four rubber feet with adhesive backing If any item is found missing or damaged, please contact your local network supplier for r
Summary of the content on the page No. 14
10/100 NWay Ethernet/Fast Ethernet Switch User’s Guide Setup The setup of the Switch can be performed using the following steps: ♦ The surface must support at least 5kg for the Switch. ♦ The power outlet should be within 1.82 meters (6 feet) of the device. ♦ Visually inspect the power cord and see that it is fully secured to the AC power connector. ♦ Make sure that there is proper heat dissipation from and adequate ventilation around the Switch. Do not place heavy objects on the Switch. Desktop
Summary of the content on the page No. 15
10/100 NWay Ethernet/Fast Ethernet Switch User’s Guide Figure 2.1 10/100 NWay Ethernet/Fast Ethernet Switch installed on a Desktop or Shelf Rack Installation The Switch can be mounted in an EIA standard size, 19-inch rack, which can be placed in a wiring closet with other equipment. For information about the DFE-700B Rack Mounting Brackets, consult your computer hardware dealer. If you already possess the brackets, attach them on the Switch’s front panel (one on each side), and then secure the
Summary of the content on the page No. 16
10/100 NWay Ethernet/Fast Ethernet Switch User’s Guide Figure 2.2 Installing the 10/100 NWay Ethernet/Fast Ethernet Switch in an equipment rack Power on The Switch can be used with AC power sources 100 - 240 VAC, 50 - 60 Hz. The power switch is located at the rear of the unit adjacent to the AC power connector. To turn the Switch on, press the power switch to the on or “1” position. The Switch’s power supply will adjust to the local power source automatically and may be turned on without havin
Summary of the content on the page No. 17
10/100 NWay Ethernet/Fast Ethernet Switch User’s Guide LED Indicators After the switch is turned on, the LED indicators should respond as follows: ♦ All of the LED indicators will blink momentarily. This blinking of the LED indicators represents a reset of the system. ♦ The power LED indicator will remain ON. Power Failure As a precaution, the Switch should be turned OFF in case of a power failure. Press the power switch to the off or “0” position. When power is resumed, turn the Switch ON. At
Summary of the content on the page No. 18
10/100 NWay Ethernet/Fast Ethernet Switch User’s Guide 3 3 IDENTIFYING EXTERNAL COMPONENTS This chapter describes the front panel, rear panel, and LED indicators of the Switch. Front Panel The front panel of the Switch consists of sixteen (10/100 Mbps MDI-X) ports, one uplink (MDI-II) port, and LED indicators. A description of the ports appears in the Introduction of this User’s Guide (see Features, Chapter 1). Figure 3.1 Front panel view of the 10/100 NWay Ethernet/Fast Ethernet Switch 8 Ide
Summary of the content on the page No. 19
10/100 NWay Ethernet/Fast Ethernet Switch User’s Guide Rear Panel The rear panel of the device consists of an AC power connector and a power switch. Figure 3.2 Rear panel view of the 10/100 NWay Ethernet/Fast Ethernet Switch ♦ AC Power Connector This is a three-pronged connector that supports the power cord. Plug in the female connector of the provided power cord into this connector, and the male into a power outlet. Supported input voltages range from 100 ~ 240 VAC at 50 ~ 60 Hz. ♦ Power Sw
Summary of the content on the page No. 20
10/100 NWay Ethernet/Fast Ethernet Switch User’s Guide Figure 3.3 The 10/100 NWay Ethernet/Fast Ethernet Switch LED indicators ♦ Power This indicator operates when the Switch is turned on. If this indicator is not lit, check the AC power connector to ensure proper insertion of the power cord and that the power switch is turned ON. ♦ 100Mbps/10Mbps The LED indicator lights when a 100 Mbps device is connected to a respective port or the uplink port. If a 10 Mbps device is connected to a respec
