Summary of the content on the page No. 1
Amplifier Manual
Model: Ti1600.5
Features:
• UncompromisedFive Channel Performancein a Single Chassis
• High, Band and LowPass Cr ossovers
• Crossoversfeatur e41 Detents for ExactFr equency Selection
• Audiophile Bi-Polar OutputT ransistors(Fr ont andRear Channels)
• HighEf ficiency ClassD T opology (Subwoofer Channel)
• MassiveDual Unr egulated Power Supplies featuring HandW ound Transformers
•Extruded Aluminum Heatsinkwith Evenflow
Summary of the content on the page No. 2
Amplifier Owner’s Manual Specifications FRONT AND REAR CHANNEL SPECIFICATIONS Frequency Response: ± 1dB from 20Hz to 20kHz Signal to Noise Ratio: >110dB High and Low Pass Crossovers: 18dB per octave Front High Pass Crossover Range: 40Hz to 4kHz Rear High Pass Crossover Range: 10Hz to 300Hz Rear Low Pass Crossover Range: 40Hz to 4kHz Low Level Input Range: 200 millivolts to 8 volts Lowest Recommend Load: 4 ohm Bridged or 2 ohm Stereo Typical Efficiency: 50% Damping Factor Greater than 2
Summary of the content on the page No. 3
Amplifier Owner’s Manual Crossover Settings All crossover frequency potentiometers have 41 detents or “clicks” so the end user can set the exact cross over frequency desired. SUB CHANNEL FRONT AND REAR CHANNELS FRONT HP REAR HP REAR LP Subsonic LP Bass Boost clicks clicks (10~55hz) (30~300Hz) (40~4kHz) (10~300Hz) (40~4kHz) 4.0k 1 58 300 0.0 1 304 4.2k 2 58 300 0.0 2 3.9k 303 4.1k 3 58 296 0.0 3 3.9k 303 4.0k 4 3.8k 302 2.9k 4 56 284 0.1 5 2.7k 299 2.5k 5 55 274 0.1 6 54 266 0.2 6 2.1k 268 2.0
Summary of the content on the page No. 4
ti1600.5 - Operational Details FRONT/REAR/ SUB INPUT LEVEL Connect signal cables from the head unit to these terminals. Used to reach maximum amplifier power with a wide variety of headunits. 2ch/4ch/5ch INPUT SELECTOR FRONT AND REAR SPEAKER OUTPUTS 2ch: Headunit has one pair of cables into front Input. Used to connect the amplifier to speakers. Minimum impedance is 2 ohm stereo/4 ohm 4ch: Headunit has two pairs of cables into front and rear inputs. bridged. Use left channel + and right channel
Summary of the content on the page No. 5
Amplifier Owner’s Manual BASS BOOST LOW PASS LEVEL CONTROL (LPL) Variable bass boost from 0 to +18dB @ 45 Hz. This port is for connecting the optional remote level control (LPL44). This allows up to 20dB of volume adjustment. This is not a bass boost, it controls the level of the sub channel. SUBSONIC CROSSOVER FREQUENCY Controls the highpass crossover point for the speaker outputs to eliminate extreme low frequencies. REMOTE MONITORING DISPLAY (RMD) Connect optional RMD Voltage Display to t
Summary of the content on the page No. 6
Amplifier Owner’s Manual System tuning 1. Install all system fuses. Note: For subwoofers controlled by the Remote level 2. Set the amplifier’s input sensitivity controls to their control, keep the level setting from step 11 or 12. Use the minimum positions (full counterclockwise). control to blend subwoofers with the rest of the system. The correct subwoofer volume will change depending on 3. S et all amplifier crossover switches according to your road noise and differences in recording
Summary of the content on the page No. 7
Amplifier Owner’s Manual TROUBLESHOOTING NO POWER: NO SOUND FROM ONE SIDE: Check voltage at amplifier with a DMM (volt meter), +12v Check the balance control in the head unit. Check speaker and R (with head unit on) the voltage should register connections. Check signal input connection. between 12.2V and 14.6V when using the ground lead of the amplifier. Check fuse at amplifier and at the battery. Use VERY LOW OUTPUT: a meter to verify connection from one end of the fuse to the Check your head
Summary of the content on the page No. 8
Phoenix Gold A Division of AAMP of America™ 13190 56th Court Clearwater, Florida 33760 P: 888-228-5560 info@phoenixgold.com www.phoenixgold.com © 2011 AAMP of Florida, Inc Designed and Engineered in the USA Phoenix Gold Product Warranty LIMITED WARRANTY ON AMPLIFIERS Phoenix Gold warrants this product to be free of defects in materials and workmanship for a period of one (1) years from the original date of purchase. This warranty is not transferable and applies only to the original purchaser
