Summary of the content on the page No. 1
24-Port 10/100Mbps with PoE
+ 2G TP/SFP Combo
Managed Ethernet Switch
WGSW-2620PV
User's Manual
Summary of the content on the page No. 2
Trademarks Copyright © PLANET Technology Corp. 2005. Contents subject to which revision without prior notice. PLANET is a registered trademark of PLANET Technology Corp. All other trademarks belong to their respective owners. Disclaimer PLANET Technology does not warrant that the hardware will work properly in all environments and applications, and makes no warranty and representation, either implied or expressed, with respect to the quality, performance, merchantability, or fitness for
Summary of the content on the page No. 3
Table of Contents 1. INTRODUCTION ................................................................................................................... 5 1.1 Packet Contents.............................................................................................................. 5 1.2 How to Use This Manual ................................................................................................. 5 1.3 Product Feature..................................................................
Summary of the content on the page No. 4
5. TROUBLESHOOTING...................................................................................................... 128 5.1 Incorrect connections .................................................................................................. 128 5.2 Diagnosing LED Indicators.......................................................................................... 128 5.3 Diagnosing POE problems.......................................................................................... 1
Summary of the content on the page No. 5
1. INTRODUCTION 1.1 Packet Contents Check the contents of your package for following parts: ▫ Fast Ethernet PoE Switch x1 ▫ CD-ROM user's manual x1 ▫ Quick installation guide x1 ▫ 19" rack mounting kit x1 ▫ Power cord x1 ▫ Rubber feet x 4 If any of these are missing or damaged, please contact your dealer immediately, if possible, retain the carton including the original packing material, and use them against to repack the product in case there is a need to return it to us for repair.
Summary of the content on the page No. 6
Gigabit fiber, 802.3af power over Ethernet ▫ High back-plane bandwidth 8.8Gbps ▫ IGMP snooping and IGMP Query mode for Multi-media application ▫ Port mirror and bandwidth control ▫ Supports GVRP function ▫ End point insert mode remote power feeding ▫ Provides extra DC 48V input with redundant function and management power status through RS-232 port ▫ On line extra power supply testing through RS-232 port ▫ Management by Web/SNMP/Telnet/Console ▫ Port Based VLAN /802.1Q Tag VLA
Summary of the content on the page No. 7
100FX module (module)): Link/Activity, Full duplex Remote power feeding End-point insert type and compatible with IEEE802.3af Per port feeding power: 15.4Watts (maximum) Power Embedded AC power supply: AC 90~240V, 2.5A, 50/60Hz, 200W Extra power input: DC48V Operating environment 0~40 , 10%~95%RH Storage environment -40 ~70 , 95% RH Dimension 440mm(W) x 280mm(D) x 44mm(H) EMI FCC Class A, CE Safety UL, cUL, CE/EN60950 Standard Compliance IEEE802.3 10BASE-T IEEE802.3u 100BASE-TX/100BAS
Summary of the content on the page No. 8
2. INSTALLATION This section describes the functionalities of the Switch's components and guides how to install it on the desktop or shelf. Basic knowledge of networking is assumed. Please read this chapter completely before continuing. 2.1 Product Description The PLANET WGSW-2620PV PoE Switch features Power-over-Ethernet (PoE), which optimizes the installation and power management of network devices such as wireless access points (AP), Voice over IP (VoIP) phones, and security video came
Summary of the content on the page No. 9
2.1.2 Switch Front Panel Figure 2-1 shows the front panel of the switch. Figure 2-1 WGSW-2620PV front panel. 2.1.3 LED Indications Network/PoE: LED Color Function PWR Green Lights to indicate that the Switch is powered on. PoE Green Lights to indicate the port is providing 48VDC in-line power. LNK/ACT Green Lights to indicate the link through that port is successfully established. FDX/COL Green Blink to indicate that the switch is actively sending or receiving data over that port.
Summary of the content on the page No. 10
2.2.1 Desktop Installation To install the Switch on desktop or shelf, please follows these steps: Step1: Attach the rubber feet to the recessed areas on the bottom of the switch. Step2: Place the switch on the desktop or the shelf near an AC power source. Step3: Keep enough ventilation space between the switch and the surrounding objects. Note: When choosing a location, please keep in mind the environmental restrictions discussed in Chapter 1, Section 4, in Specification. Step4: Connect
Summary of the content on the page No. 11
Step4: Follow the same steps to attach the second bracket to the opposite side. Step5: After the brackets are attached to the Switch, use suitable screws to securely attach the brackets to the rack, as shown in Figure 2-6 Figure 2-6 Mounting the Switch in a Rack Step6: Proceeds with the steps 4 and steps 5 of session 2.2.1 Desktop Installation to connect the network cabling and supply power to the switch.
Summary of the content on the page No. 12
3. CONSOLE MANAGEMENT 3.1 Connecting to the Switch The console port is a female DB-9 connector that enables a connection to a PC or terminal for monitoring and configuring the Switch. Use the supplied RS-232 cable with a male DB-9 connector to connect a terminal or PC to the Console port. The Console configuration (out of band) allows you to set Switch for remote terminal as if the console terminal were directly connected to it. 3.2 Login in the Console Interface When the connection betwe
Summary of the content on the page No. 13
bring out the login prompt. Key in the “admin“(default value) for the both User name and Password (use Enter key to switch), then press Enter key and the Main Menu of console management appears. Please see below figure for login screen. Console login screen 3.3 CLI Management The system supports two types of console management - CLI command and Menu selection. After you login to the system, you will see a command prompt. To enter CLI management interface, enter "enable" command. The fol
Summary of the content on the page No. 14
information. The privileged command is advance mode Enter the enable Privileged Privileged this mode to Enter disable to command while in switch# exit. EXEC • Display advance user EXEC mode. function status • Save configures Enter the configure To exit to Use this mode to Global command while in switch privileged EXEC configure parameters that Configuratio privileged EXEC (config)# mode, enter exit apply to your switch as a n mode. or end whole. Enter the vlan To exit to user
Summary of the content on the page No. 15
3.3.2 Commands Set List 3.3.2.1 System Commands Set Command Commands Description Defaults Example Level Global system name Set switch system name Switch (config)# configuration [systemname] string system name xxx mode system Global location Set switch system location Switch (config)# configuration [system string system location xxx mode location] system Global Switch (config)# description Set switch system configuration system description description string [systemdescr
Summary of the content on the page No. 16
Global Switch (config)# default configuration Restore to default default mode Global username Changes a login username. Switch (config)# configuration [user-name] (maximum 10 words) username xxxxxx mode Switch (config)# Global password Specifies a password password xxxxxx configuration [password] (maximum 10 words) mode Switch> show system info Name: switch1 location: lab show system User EXEC Show system information info Description: layer2 switch Contact: somew
Summary of the content on the page No. 17
Switch# show accounting Privileged show Show username & accounting password Username: admin EXEC Password: admin Switch> show version Use the show version user Firmware version: EXEC command to display 1.0 show version User EXEC version information for the Hardware version: hardware and firmware. 3.0 Kernel version: 1.10 Switch (config)# show terminal Baud rate (bits/sec): Use the show terminal 9600 Privileged command to display show terminal Data Bits: 8 console
Summary of the content on the page No. 18
Switch (config)# Use the module Ethernet interface interface configuration moduleEthernet command 1/1 Use the duplex Switch (config)# configuration command interface to specify the duplex fastEthernet 0/1 Auto mode of operation for Fast Switch (config-if)# duplex full Interface Ethernet. duplex [full | half| configuratio auto] n mode Switch (config)# Use the duplex interface configuration command moduleEthernet to specify the duplex Auto 1/1 mode of operation for
Summary of the content on the page No. 19
for speed 100) (The 1000Base-FX module only supported for speed 1000 & auto) Use the flow control configuration command Switch (config)# on Ethernet ports to interface Interface control traffic rates during flowcontrol on or fastEthernet 0/1 configuratio On congestion. no flowcontrol n mode Switch (config-if)# Use the no form of this flowcontrol on command to disable security on the port. Use the security Switch (config)# configuration command interface Interface on Et
Summary of the content on the page No. 20
Set bandwidth in or out Switch (config)# rate. The value rage is interface Interface (0~999), and zero of the Bandwidth [in | out] fastEthernet 0/1 configuratio Disable value is disable [value] n mode Switch (config-if)# (The module can’t be bandwidth hi 50 setting) Use the state interface Switch (config)# configuration command interface Interface to specify the state mode State [Enable | fastEthernet 0/1 configuratio of operation for Ethernet Enable Disable] n mode port
