Summary of the content on the page No. 1
20 METER (14 MHZ)
ALL MODE RECEIVER KIT
Ramsey Electronics Model No. HR20
Here’s the ideal mini-receiver for catching all the busy action on
20 meters from your office, home or on trips!
Small in size but BIG in features:
• Easily tunes SSB, CW, RTTY and AM
• Smooth varactor tuning of any desired 250KHz segment of the 20
meter band, easily retuned
• Front panel RF Gain, Tuning and Volume controls
• Efficient LM-386 Audio amplifier drives speaker or earphones with a
clean, cr
Summary of the content on the page No. 2
PARTIAL LIST OF AVAILABLE KITS RAMSEY TRANSMITTER KITS • FM10A, FM25B Stereo Transmitters • AM1, AM25 AM Transmitters • TV6 Television Transmitter • FM100B Professional FM Stereo Transmitter RAMSEY RECEIVER KITS • FR1 FM Broadcast Receiver • AR1 Aircraft Band Receiver • SR2 Shortwave Receiver • AA7 Active Antenna • SC1 Shortwave Converter RAMSEY HOBBY KITS • SG7 Personal Speed Radar • SS70A
Summary of the content on the page No. 3
Ramsey Publication No. MHR20 Price $5.00 KIT ASSEMBLY AND INSTRUCTION MANUAL FOR HR20 AMATEUR RECEIVER KIT TABLE OF CONTENTS Introduction to the HR20 .................4 About Direct Conversion .................5 Circuit description ...........................6 Parts list ..........................................7 Schematic diagram .........................9 Parts layout ...................................10 Assembly instructions ...................11 Initial testing ...........
Summary of the content on the page No. 4
INTRODUCTION: If you like plenty of action and DX (long distance) communications, the 20 meter Ham band is the place to be. Almost 24 hours a day there’s something interesting happening on 20 meters. There are several groups of people who will enjoy this Ramsey HR20 Receiver: • Experienced Ham operators who want a simple extra receiver for keeping one ear on 20 meters while doing something else. • Beginners who would like to start by listening in on one of Ham radios most active bands.
Summary of the content on the page No. 5
This receiver circuit is ideal for discovering just how simple a true “Communications Receiver” can be . That’s right- there is a BIG difference between the Ramsey HR20 and other simple short wave radio circuits we can try to build. Yet it is very easy to build. Our HR-series are by far the easiest to build of all the Ramsey kit receivers and therefore very nice for radio newcomers. Consequently, our manuals for the 40 and 80 meter receivers are written with beginners in mind, since both
Summary of the content on the page No. 6
Advantages of any Direct Conversion receiver include: • It is simple, and therefore economical and easy to build • It is quite sensitive even with a simple antenna • Its tuning oscillator could even be set up to serve directly as a transmitter VFO in a simple transceiver setup. A common problem with DC receivers is that they are easily overwhelmed by strong AM broadcast stations from almost anywhere, whether it’s your local rock and roll broadcaster, Radio Moscow or the Voice of America.
Summary of the content on the page No. 7
PARTS SUPPLIED WITH THE HR20 KIT: CAPACITORS: 1 15pF ceramic disc capacitor [marked 15 or 15K] (C4) 1 27pF ceramic disc capacitor [marked 27 or 27K] (C13) 2 36pF ceramic disc capacitor [marked 36 or 36K] (C1,C2) 4 .01µF disc capacitor [marked 103 or .01 or 10nF] (C3,C5,C6,C7) 2 4.7 to 10µF electrolytic capacitor (C8,C9) 3 100-220µF electrolytic capacitor (C10,C11,C12) RESISTORS: 3 10K ohm potentiometers (R1,R2,R3) 1 270 ohm resistor [red-violet-brown
Summary of the content on the page No. 8
"LEARN-AS-YOU-BUILD" RECEIVER ASSEMBLY STRATEGY: To help you learn just what exactly is going on we'll discuss the purpose of most of the components or groups of components as we go along. Since we are trying to keep assembly of the board simple, we will not be able to fully describe each individual component’s function as you build, but Ramsey's "Learn-As-You-Build" kit assembly philosophy still stands. Check off each step as understood and completed. Examine the schematic diag
Summary of the content on the page No. 9
HR20• 9
Summary of the content on the page No. 10
HR20 PARTS LAYOUT DIAGRAM HR20• 10
Summary of the content on the page No. 11
RECEIVER ASSEMBLY: 1. Install the RCA antenna jack, J1. Solder all four points. 2. Install C5, a .01µF ceramic disc signal coupling capacitor . This capacitor brings the signal up to the front of the PC board. Notice the long PC trace from J1 through C5 to R1. 3. Install potentiometer R1, the RF gain control. Insert it into the PC board so that it seats firmly and is straight and even. Solder the three pins and the two mounting tabs. 4. Examine inductor L1. Look at the bottom s
Summary of the content on the page No. 12
are marked by polarity and must be installed in the proper direction. You’ll see that one side of the capacitor has a black band and is marked with a ‘-’ sign. This is the negative side, the other side is the positive lead. Make sure you insert the positive lead into the ‘+’ marked hole on the PC board. 12. Install C11, a 100-220µF electrolytic capacitor. Remember to observe correct polarity. C10 and C11 provide voltage stabilizing which directly improves the performance of the SA602 osci
Summary of the content on the page No. 13
25. Install the 9-volt battery snap connector, making sure that the red (+) and black (-) leads are correctly installed. 26. Install C7, .01µF disc capacitor (marked 103 or .01 or 10nF). 27. Install C8, 4.7-10µF electrolytic capacitor. Observe polarity. 28. Install U2, the LM386 audio amplifier IC chip. Just like the SA602, you must correctly position the notched or banded end. 29. Install R6, 10K ohm resistor (brown-black-orange). 30. Install C12, 100-220µF electrolytic capacitor;
Summary of the content on the page No. 14
INITIAL TESTING OF YOUR HR20: You’re now ready to power up and test your HR20, but before you begin take some time to sweep off your bench of any loose component leads or solder splashes. A clean work area not only makes testing less frustrating but also less prone to problems. REQUIRED FOR INITIAL TESTING AND ALIGNMENT: A known frequency standard in the 10MHz range such as: • Crystal oscillator or, • RF signal generator or, • Grid Dip oscillator or, • QRP transmitter such as a Ramsey
Summary of the content on the page No. 15
Alignment: Turn on whatever reference signal source you plan to use. This can be a regular transceiver keying a few milliwatts into a dummy load, a crystal oscillator or a signal generator. Or, you can look for a known signal that you have tuned in on another receiver. If you are without any reference signal whatsoever but have a reasonable antenna , you can use your familiarity with the 20m band to make a rough alignment of the receiver. If Ham radio and 20 meters are new to you, here’s
Summary of the content on the page No. 16
USING YOUR RECEIVER: In your first tests, you might feel that tuning in CW and SSB stations by turning the control shaft seems tricky. Don't despair! The addition of a simple knob to the final version of your kit will result in more comfortable tuning right away. Also, the larger the knob, the easier tuning is. Even smoother control can be accomplished by a vernier dial, which will also provide calibration marks. Finally, if you intend to use this receiver only for monitoring or working a
Summary of the content on the page No. 17
SA602 audio output at the volume control, and switch in a pleasant oscillator pitch (keying sidetone) which is amplified to listening level by LM386. The Ramsey Electronics Universal timer kit No. UT-5 is easily adapted as a sidetone oscillator. • SPEAKER OPERATION A fifty cent, two inch diameter speaker, lying naked on your workbench will give you a fair test of the speaker output capability. Speaker quality and well- designed enclosures have their clear purposes! A reasonable speaker in
Summary of the content on the page No. 18
• MORE AUDIO POWER - ANOTHER WAY If you want to use your HR20 for casual band monitoring while you are busy across the room, in the shop, to share with a class or club or group and want LOTS more volume, try building up our very inexpensive Ramsey BN-9, 2 watt general purpose amplifier kit. Supply DC voltage to such an amplifier separately, using D-cells, a lantern or auto battery , or a well filtered power supply. • ADDING AN LED POWER ON INDICATOR For many people, a pilot lamp to indic
Summary of the content on the page No. 19
TROUBLESHOOTING TIPS: PROBLEM: ALL signals are chirpy and unstable. SOLUTION: Sorry to have to say it , but this condition is only caused by a weak battery! Use a fresh alkaline cell. Any strong signal forces the audio circuit to rob voltage from the oscillator, which cause the instability. PROBLEM: Occasionally good but erratic operation. SOLUTION: Check very carefully for a poor solder connection. PROBLEM: Signals have an unpleasant hissing pitch. SOLUTION: Try a different set of head
Summary of the content on the page No. 20
GENERAL NOTES FOR EXPERIENCED QRP BUILDERS: We at Ramsey Electronics deliberately designed the HR-series of DC receivers to be easily available, affordable and buildable by any person willing to follow the assembly directions. To achieve this goal, the current models, with direct coupling of the SA602 to the LM386 operating with a gain figure of 50, use an amazing minimum of parts. If you know what you are doing with DC receiver design, we encourage you to use our HR-series for reliable b
