Summary of the content on the page No. 1
User’s manual
TL86009
DECT 6.0 expansion handset
for use with AT&T model
TL86109
corded/cordless telephone/
answering system with
BLUETOOTH® wireless technology
Summary of the content on the page No. 2
Congratulations on purchasing your new AT&T product. Before using this AT&T product, please read Important safety information on pages 24-26. For complete instructions, please refer to the manual provided with your TL86109 telephone. For customer service or product information, please visit our website at www.telephones.att.com or call 1 (800) 222-3111. In Canada, dial 1 (866) 288-4268. Model #: TL86009 Type: DECT 6.0 expansion handset Serial #: Purchase date: Place of purchase: Bot
Summary of the content on the page No. 3
Parts checklist Your telephone package contains the following items. User’s manual TL86009 DECT 6.0 expansion handset for use with AT&T model TL86109 corded/cordless telephone/ answering system with BLUETOOTH® wireless technology User’s manual Cordless handset Charger for cordless handset with power adapter installed Battery for Battery compartment cover Belt clip for cordless handset cordless handset
Summary of the content on the page No. 4
User’s manual TL86009 DECT 6.0 expansion handset for use with AT&T model TL86109 corded/cordless telephone/ answering system with BLUETOOTH® wireless technology Table of contents Getting started Important safety information ....................................24 Installation ....................................... 1 Safety information ................24 Quick reference guide ............... 2 Especially about corded Charger installation ..................... 5 telephones ...............
Summary of the content on the page No. 5
Getting started Installation You must install and See pages 6-8 for easy charge the handset instructions. battery before using the cordless handset. Your product may be shipped with a protective sticker covering the handset display - remove it before use. For customer service or product information, visit our website at www.telephones.att.com or call 1 (800) 222-3111. In Canada, dial 1 (866) 288-4268. Avoid placing the telephone base too close to: • Communication devices such as televis
Summary of the content on the page No. 6
Getting started Quick reference guide Softkeys (2) Press to select a menu item displayed above the key. OFF/CLEAR While using menus, press CHARGE light to cancel an operation, (blue ring around back up to the previous DIR/ /VOL/ /CID) menu, or exit the menu On when the handset is display. Press and hold to charging in the charger. return to idle mode. While entering names or numbers, press to delete a DIR/ /VOL digit or a character. Press to scroll up while During a call, press to
Summary of the content on the page No. 7
Getting started Quick reference guide 1 LINE/FLASH/ 2 LINE/FLASH 1 Press 1 LINE/FLASH While reviewing a caller to make or answer a ID history entry, press call on line 1. During a repeatedly to add or call, press to answer an remove 1 in front of incoming call on line 1 the telephone number when you receive a call before dialing or saving waiting alert. it in the directory. Press 2 LINE/FLASH to make or answer a call on line 2. During a TONE call, press to answer an incoming cal
Summary of the content on the page No. 8
Getting started Quick reference guide EQ During an outside call, intercom call, message or announcement playback, press to change the quality of the audio to best suit your hearing. Press the MENU softkey to enter the main menu which includes the following: PLAY MESSAGES HANDSET ANSWERING SYS L1) DIRECTORY L2) CALL LOG CL) INTERCOM MENU RINGER SETTINGS WEBSITE PLAY MESSAGES BACK SELECT 4
Summary of the content on the page No. 9
Getting started Charger installation Install the charger as shown below. Plug the power adapter into an electrical outlet not controlled by a wall switch. IMPORTANT INFORMATION: 1. Use only the power adapter provided with this product. To obtain a replacement, visit our website at www.telephones.att.com or call 1 (800) 222-3111. In Canada, dial 1 (866) 288-4268. 2. The power adapter is intended to be correctly oriented in a vertical or floor mount position. The prongs are not designed to hol
Summary of the content on the page No. 10
Getting started Battery installation and charging Install the battery as shown below. Step 1 Step 2 Plug the battery Align the cover flat connector securely against the battery into the socket inside compartment, then the handset battery slide it upwards until compartment, matching it clicks into place. the color-coded label. Insert the supplied battery with the label THIS SIDE UP facing up as indicated. Step 3 Charge the handset by placing it face up in the charger. The CHARGE light C
Summary of the content on the page No. 11
Getting started Battery installation and charging After you install your telephone or power SET DATE returns following a power outage, the handset --/--/-- will prompt you to set the date and time. To skip MM/DD/YY setting the date and time, press OFF/CLEAR. SET SET TIME --:-- -- SET To replace the battery, press the tab and slide the battery compartment cover downwards. Lift out the old battery and disconnect it from the handset. Follow the instructions on page 6 to ins
Summary of the content on the page No. 12
Getting started Battery charging Once you have installed the battery, the screen indicates the battery status (see table below). If necessary, place the handset in the charger to charge the battery. For best performance, keep the handset in the charger when not in use. The battery is fully charged after 16 hours of continuous charging. See the table on page 33 for battery operating times. If the screen shows Low battery, you need to charge the battery without interruption for at least 25 m
Summary of the content on the page No. 13
Getting started Belt clip & optional headset To remove the belt clip: To attach the belt clip: Gently lift either of the belt clip tabs, shown Snap the belt clip in the figure, outwards into the slots on both to remove the belt clip sides of the handset as from the handset. shown in the figure. For handsfree telephone conversations, you can use any industry standard 2.5 mm headset (purchased separately). For best results, use an AT&T 2.5 mm headset. To purchase a headset, visit our web
Summary of the content on the page No. 14
Adding handset to your telephone base Adding and registering handsets Before using a new TL86009 handset, you must register it with the AT&T TL86109 telephone system (purchased separately). The AT&T TL86109 telephone system can accommodate up to 12 handsets. The handset provided with the TL86109 comes registered as HANDSET. You can register up to 11 additional handsets to the telephone base, and they will be assigned numbers in the order they are registered (HANDSET 2, HANDSET 3, HANDSET
Summary of the content on the page No. 15
Adding handset to your telephone base Expand your telephone system Add and register a handset When first purchased, each expansion handset shows Press [HOLD] on base for 4 sec, then press [#] on handset after a battery is installed. Each handset should be charged without interruption for at least 25 minutes before registering to the telephone base. For more details on battery charging, see the table on page 8. To register a handset: 1. Press and hold HOLD on the telephone base for about
Summary of the content on the page No. 16
Adding handset to your telephone base Replace a handset If you want to replace a handset or reassign the designated handset number of a registered handset, you must deregister all the handsets and then individually register each handset. To make deregistration easier, read all of the instructions on this page before you begin. To deregister all handsets: 1. Press and hold FLASH on the telephone base for about 4 seconds until it shows Deregister all handsets? 2. Press the Yes softkey to con
Summary of the content on the page No. 17
Appendix Troubleshooting If you have difficulty with your telephone, please try the suggestions below. For customer service, or to purchase accessories or replacement parts, visit our website at www.telephones.att.com, or call 1 (800) 222-3111. In Canada, dial 1 (866) 288-4268. My phone doesn’t work at all. • Make sure the power cord is securely plugged in. • Make sure that the battery connector is securely plugged into the cordless handset. • Make sure the telephone line cord is securely
Summary of the content on the page No. 18
Appendix Troubleshooting I cannot get a dial tone. • First try all the suggestions above. • Move the cordless handset closer to the telephone base. You might have moved out of range. • If the previous suggestions do not work, disconnect the telephone base from the telephone jack and connect to a different phone. If there is no dial tone on that phone either, the problem is in your wiring or local service. Contact your telephone service provider. • Your line cord might be malfunctioning. Tr
Summary of the content on the page No. 19
Appendix Troubleshooting My cordless handset isn’t performing normally. • Make sure the power cord is securely plugged into the telephone base. Plug the power adapter into a different working electrical outlet not controlled by a wall switch. • Move the cordless handset closer to the telephone base. You might have moved out of range. • Reset the telephone base. Unplug the electrical power. Wait for 15 seconds then plug it back in. Allow up to one minute for the cordless handset and telephon
Summary of the content on the page No. 20
Appendix Troubleshooting Out of range OR no power at base appears on my cordless handset. • Ensure that the telephone base is powered up. • Move the cordless handset closer to the telephone base. You might have moved out of range. • Reset the telephone base. Unplug the electrical power. Wait for 15 seconds then plug it back in. Allow up to one minute for the cordless handset and telephone base to reset. • Other electronic products such as HAM radios and other DECT phones can cause interfere
