Summary of the content on the page No. 1
™
IllumiClean
U S E R ’ S G U I D E
6 8 G 9 S E R I E S 2 2 0 - 2 4 0 v
3
Safety Instructions
4
Product View
5-6
Assembly
7-9
Operations
10-12
Maintenance and Care
13
Troubleshooting
14
Consumer Services
15
Replacement Parts
16
Warranty
Summary of the content on the page No. 2
Thanks for buying a BISSELL IllumiClean™ Canister Vacuum We’re glad you purchased a BISSELL IllumiClean canister vacuum. Everything we know about floor care went into the design and construction of this complete, high-tech home cleaning system. Your BISSELL canister vacuum is well made, and we back it with a limited two year warranty. We also stand behind it with a knowledgeable, dedicated Consumer Services department, so, should you ever have a problem, you’ll receive fast, considerate
Summary of the content on the page No. 3
IMPORTANT SAFETY INSTRUCTIONS ■ When using an electrical appliance, Remove plug from electrical outlet before cleaning or basic precautions should be observed, maintaining the appliance. including the following: ■ If the supply cord is damaged, it must be replaced by the manufacturer or its service agent in order to REaD all InStRUctIonS avoid a hazard. ■ Do not pick up toxic material (chlorine bleach, bEfoRE USInG yoUR ammonia, drain cleaner, petrol, etc.). canIStER vacUUM. ■ Do no
Summary of the content on the page No. 4
Handle Product view Air Flow Regulator Flex Hose Tool Caddy Swivel Hose Telescoping Extension Wand Variable Suction Power Control Automatic Cord Power Button Rewind Button Bag Change Indicator Brush Switch Post-Motor HEPA Media Filter Multi-Surface Carry Handle Floor Nozzle caUtIon: Do not plug in your vacuum until you are familiar with all instructions and operating procedures. Upholstery Tool Crevice Tool Dusting Brush Tool Caddy 4 w w w . b i s s e l l . c o m
Summary of the content on the page No. 5
Assembling your vacuum WaRnInG: 1. Connect swivel hose by squeezing both Plastic film can be dangerous. locking buttons and inserting it into the suction opening on the canister. Once the to avoid danger of suffocation, swivel hose is inserted in the suction opening, keep away from babies and release the locking buttons. children. 2. Connect telescoping extension wand to the handle end of the flex hose. Twist slightly to 2. 1. tighten. 3. Attach the tool holder to the telescoping extens
Summary of the content on the page No. 6
Assembling your vacuum 5. Once assembled, you can store your vacuum in one of two positions: Storing in the in-use position a2. a1. a. Storing in the in-use position: 1. To store with the floor nozzle attached, insert the storage clip (located on the back of the floor nozzle) into the storage slot on the rear of the vacuum. 2. To store without the floor nozzle attached, insert the storage clip (located on the bottom of the telescoping Storing in the upright position extension wand) int
Summary of the content on the page No. 7
Operations Power cord the power cord is located at the rear of the vacuum. Gently pull out the power cord, watching for the yellow line. Stop pulling the power cord once the yellow line is visible. there is also a red line, which indicates the end of the usable cord. Do not pull the power cord out beyond the red line. Automatic Cord Rewind Automatic cord rewind Button your vacuum is equipped with an automatic cord rewind. When cleaning is finished, press the power button off and grasp
Summary of the content on the page No. 8
Operations Special tools Tip: your bISSEll Illumiclean is not only a powerful carpet and rug vacuum cleaner, it’s Before cleaning under also a versatile bare floor vacuum cleaner and low furniture, check area first for objects above floor vacuum cleaner when you select that might harm the one of the special tools. unit or block the hose. floor nozzle: Use to vacuum carpets, rugs and bare floors. 1. Swivel head turns to get into tight spaces Brush Up and fits under cabinets. 1. To vac
Summary of the content on the page No. 9
Operations Variable suction power control the variable suction power control is located on the top of the vacuum. Slide the control toward the larger dots for maximum suction. Slide the control toward the smaller dots to minimize suction for lightly soiled areas or delicate fabrics. Air flow regulator open the air flow regulator by sliding the regulator back towards the handle to an open position to reduce suction for delicate fabrics. close the air flow regulator by sliding the regulato
Summary of the content on the page No. 10
Maintenance and care Dust bag replacement 1. Unplug the vacuum from electrical outlet. 2. 2. Open the dust bag compartment by lifting up on the latch on the door on the front of the vacuum. 3. Lift out the dust bag holder and dust bag. 4. Release the dust bag from the holder by pressing the dust bag holder clip and pulling 3. the dust bag out of the holder. Discard the used dust bag. 5. Slide the new dust bag into the holder by inserting the dust bag into the tabs located at the bottom
Summary of the content on the page No. 11
Maintenance and care Cleaning the pre-motor filter t he pre-motor filter protects the motor from notIcE: this product is intended for household dirt and dust particles. use only and not for commercial or 1. Unplug the vacuum from electrical outlet. industrial use. vacuuming of dust from products like plaster, concrete or 2. Open the dust bag compartment by lifting ashes will damage the motor and void up on the latch on the door at the front of the warranty. the vacuum. Lift out the d
Summary of the content on the page No. 12
Maintenance and care Replacing the post-motor HEPA media filter t he post-motor HEPa media filter assists in 2. the filtration process to return clean air to the room. 1. Unplug the vacuum from electrical outlet. 2. Remove the filter door (located on the rear of the vacuum) by pulling up on the filter door latch. 3. Remove the post-motor HEPA media filter by 3. grasping the lip of the filter frame and pulling up. 4. Replace the post-motor HEPA media filter with a new filter. notE: th
Summary of the content on the page No. 13
Troubleshooting Wa Rn In G: to reduce the risk of electric shock, turn power off and disconnect plug from electrical outlet before performing maintenance or troubleshooting. vacuum cleaner won’t run Possible causes Remedies 1. Vacuum cleaner is not plugged in 1. Check electrical plug 2. Power button is not pressed down 2. Press power button down vacuum cleaner won’t pick up or low suction Possible causes Remedies 1. Tools, flex hose and/or telescoping 1. Remove each part and check for bl
Summary of the content on the page No. 14
BISSELL Consumer Services If your bISSEll product should require service: In the UK, Australia, New Zealand, the middle east or Africa, call BIssell Consumer services at the numbers below and we will give you the location of a BIssell Authorized service Center in your area. For all other countries, contact your local in country distributor for questions, service, or repair. If you have questions about your warranty or need replacement parts please contact the numbers below. for UK inquiries:
Summary of the content on the page No. 15
Replacement parts - BISSELL IllumiClean Item Part no. Part name 1 203-7270 Dust Bag (3pk) 2 203-7268 Pre-motor Filter 3 203-7269 Post-motor hePA media Filter 4 203-7267 Floor Nozzle for australian inquiries: 5 203-7257 Flexible hose with handle 6 203-7256 Telescoping extension Wand monday - Friday 9 am — 5 pm 7 203-7273 Upholstery Brush bISSEll aUSt Ral Ia Pty l IMIt ED 8 203-7272 Dusting Brush Unit 35 9 203-7271 Crevice Tool 15 Ricketts Road mount Waverley, Victoria 3149 10 203-7
Summary of the content on the page No. 16
Warranty - BISSELL IllumiClean Canister Vacuum This warranty gives you specific legal rights, and you may also have other rights which may vary from country to country. If you need additional instruction regarding this warranty or have questions regarding what it may cover, please contact BIssell Consumer services by telephone, or regular post as described below, or contact your local in country distributor. limited two year Warranty subject to the *eXCePTIoNs AND eXClUsIoNs identified be
