Summary of the content on the page No. 1
Installation
Instructions
If you have questions, call 800.GE.CARES or visit our website at: monogram.com
Island Vent Hoods
Models:
ZV42I
ZV54I
Summary of the content on the page No. 2
Installation Instructions BEFORE YOU BEGIN WARNING: TO REDUCE THE RISK OF FIRE, ELECTRICAL SHOCK OR Read these instructions completely and INJURY, OBSERVE THE FOLLOWING: carefully. A. Use this unit only in the manner intended by the • IMPORTANT – Save these instructions for local manufacturer. If you have any questions, contact the inspector’s use. manufacturer. B. Before servicing or cleaning unit, switch power • IMPORTANT – Observe all governing codes and off at the service panel and lock
Summary of the content on the page No. 3
Design Information CONTENTS Design Information Installation Instructions Product Dimensions ......................................................................3 Step 1, Construct Ceiling Support ......................................10–12 Duct Cover Accessories ..............................................................4 Step 2, Mount Template..............................................................13 Product Clearances .................................................................
Summary of the content on the page No. 4
Design Information PRODUCT CLEARANCES DUCT COVER ACCESSORIES *Height to Ceiling 20" For ZV42I 30" Min. 24" For ZV54I 36" Max. 36" Min. ZV42I * 9" for ceiling heights 7’11" to 8’5" using the supplied support frame and duct cover. These vent hoods must be installed 30" min. to 36" max. Order ZX42DC10 for ceiling heights of 8"6" to 10’4". above the cooking surface. Exact installation height is determined by ceiling height. The cooking surface ZV54I should be at least 36” above the floor. * 5" for
Summary of the content on the page No. 5
Advance Planning ADVANCE PLANNING POWER SUPPLY Ductwork Planning IMPORTANT - (Please read carefully) • These vent hoods are equipped for 10” round ductwork. WARNING: • Determine the exact location of the vent hood. FOR PERSONAL SAFETY, THIS APPLIANCE • Plan the route for venting exhaust to the outdoors. MUST BE PROPERLY GROUNDED. • Use the shortest and straightest duct route possible. For satisfactory performance, duct run should not ATTENTION – POUR DES exceed 150 ft. equivalent length for a
Summary of the content on the page No. 6
Advance Planning Model ZV42I INSTALLATION HEIGHT REQUIREMENTS Actual Chimney Length at Duct • These vent hoods must be installed 30" min. and 36" max. Ceiling Hood Installation Height Cover above the cooking surface – regardless of the ceiling Height 30" 31" 32" 33" 34" 35" 36" Kit height. Therefore, installation height of the hood depends 10’4" 36 35 34 33 32 on the exact ceiling height of the kitchen. 10’3" 36 35 34 33 32 31 Order 10’2" 36 35 34 33 32 31 30 ZX42DC10 • Accessories are available
Summary of the content on the page No. 7
Advance Planning Equivalent Quantity Total DUCT FITTINGS Duct Piece Length* Used Length Use this chart to compute maximum 10" round to 8" round 5 ft. permissible lengths for duct runs to outdoors. Round, 1 ft. For best results, use 10" diameter duct. straight (per foot Note: Do not exceed maximum permissible length) equivalent lengths! 90° elbow 8" Dia. 52 ft. Maximum recommended duct 10" Dia. 24 ft. length for these hoods: 150 feet 45° elbow 8" Dia. 31 ft. Flexible ducting: 10" Dia. 14 ft. If
Summary of the content on the page No. 8
Installation Preparation TOOLS AND MATERIALS REQUIRED 7/16" Pivoting (NOT SUPPLIED) hex socket with 4" Hammer and 6" extensions Duct tape Electric or battery operated drill Wire cutter/stripper and 3/16", bits, Phillips and Flat Key Hole Saw Blade Screwdriver bits. Pencil and tape measure 10" round metal Safety glasses duct, length to Wire nuts Spirit level suit installation. Phillips and flat blade Flashlight screwdrivers Saber saw Strain relief for or Sawsall junction cover. Step ladder 120
Summary of the content on the page No. 9
Installation Preparation PARTS PROVIDED Locate the parts packed with the hood. Allen Wrench Support frame for 8 ft. ceiling Transition with Damper with 4 large pan head screws installed on the bottom corners. Implement rods with standoffs 2-piece decorative duct cover Duct collar Decorative top cover 2 Filters (3 with 54" hood) 2 Grease trays (3 with 54" hood) HARDWARE PACKAGE ACCESSORY PACKAGE Locate and check Check accessory package. contents. Screws Select the taller set for 9’6" to 10’4" ce
Summary of the content on the page No. 10
Installation Instructions STEP 1 CONSTRUCT CEILING SUPPORT Plan the Location of the Hood and Ductwork • The hood should extend beyond the front and rear edge • Use a plumb bob to check the location. The of the cooking appliance. countertop/cooktop below the hood must be centered • The duct in the ceiling must be centered over the with the hood. cooktop. Ceiling Ceiling Hood Hood Ducting Ducting Centerline Centerline Front Front 18-1/8" 15-7/8" 36-1/4" 31-3/4" Align With Align With Cooktop C
Summary of the content on the page No. 11
Installation Instructions STEP 1 CONSTRUCT CEILING SUPPORT CONTINUED 12-3/4” (42” Hood) EXAMPLE B 17” (54” Hood) Install Cross- Framing 16” Joist Symmetrically About Spacing Duct/Cooktop Centerline 2x4 Cross Framing 10” Duct 8 5/8” Front Align duct Cooktop of Hood to center of Outline Cooktop Top View – Ceiling Joists Run Perpendicular to Front of Hood EXAMPLE C 12-3/4” (42” Hood) 2x4 Cross 17” (54” Hood) Install Cross-Framing Framing Symmetrically About Duct/Cooktop Centerline 8 5/8” 10” Duc
Summary of the content on the page No. 12
Installation Instructions STEP 1 CONSTRUCT CEILING SUPPORT CONTINUED • Secure each 2 x 4 block with at least four (4), #10 wood 2x 4 Min. Cross Framing screws, 3” long (not supplied). Use 8 wood screws total for the two supports. • The cross framing must be accurately aligned to assure correct positioning of the hood. • The cross framing must be level in all directions. Check with a spirit level and adjust if necessary. Ceiling IMPORTANT: The ceiling structure must be capable of Joist support
Summary of the content on the page No. 13
Installation Instructions STEP 2 MOUNT TEMPLATE • Select the template for your hood size. • Align the template with the marks on the ceiling and tape in place. – Be sure the template is oriented correctly, with the front of the hood. • Use a plumb to check to be sure the mounting holes will provide parallel alignment with the countertop below. • Center punch all hole locations. 1/4" Gap • Drill pilot holes in the 4 screw locations. Use a 3/16” bit and drill approximately 1-1/2” deep. • Drive 4
Summary of the content on the page No. 14
Installation Instructions STEP 4 INSTALL ACCESSORY (OR SUPPLIED) SUPPORT AND DUCT COVERS Install Small Pan Head Screws on Each Side Top Duct Cover Screws D Bottom Duct Cover Adjust Install Frame to Install Stop Safety Screw nstallation Screw on Each Side Height Screws E Stop Screw Storage Location Install supplied support frame OR telescoping accessory frame CAUTION: The stop screw • Hang the supplied support frame or telescoping must be installed. Failure to do so could result in accessory
Summary of the content on the page No. 15
Installation Instructions STEP 5 INSTALL DUCT TRANSITION STEP 6 INSTALL HOOD WITH DAMPER Note: THREE PEOPLE ARE REQUIRED TO Bumper Pads COMPLETE THIS INSTALLATION! Duct Transition 1/4" Gap Attachment Screws Attachment Keyholes Screws C IMPORTANT: Remove shipping tape from damper and • Back out the hanging screws on the bottom of the check that damper moves freely. support frame to a 1/4" gap. • Place the transition piece over the hood exhaust and • Lift the hood up to the support frame. Carefu
Summary of the content on the page No. 16
Installation Instructions STEP 8 CONNECT ELECTRICAL Verify that power is turned off at the source. • Install strain relief onto the knockout of the junction box. WARNING: If house wiring is not • Insert house wiring through strain relief and tighten. 2-wire with a ground wire, a ground must be provided • Use wire nuts to connect incoming ground to green, by the installer. When house wiring is aluminum, be white to white and black to black. sure to use UL approved anti-oxidant compound and • Pus
Summary of the content on the page No. 17
Installation Instructions STEP 10 SLIDE DUCT COVER STEP 12 INSTALL RODS DOWN • Use a flat blade screwdriver to install stand-offs into SKIP THIS STEP IF USING THE SUPPLIED DUCT the bottom of the hood. COVER • Align implement rod to stand-offs with the screw hole towards the inside of the hood. Secure the rod to the • Hold the duct cover in place and remove the stand-offs with the supplied Allen wrench. temporary stop screw. Return the screw to the • Follow the same procedure on the opposite s
Summary of the content on the page No. 18
Installation Instructions STEP 14 FINALIZE INSTALLATION STEP 13 INSTALL SUPPLIED DUCT COVER AND TOP COVER • Check all lamps to assure tightness in sockets. • Turn power on at the circuit breaker. • Refer to the Owner’s Manual for operating and Install Duct cleaning instructions. Cover Screw on Each Side Screws D • Install the supplied 2-piece duct cover over the support frame (if using supplied frame). Snap ends together. • Secure duct covers to support frame with 2 Screws D. • For a more fin
Summary of the content on the page No. 19
Installation Instructions STEP 15 INSTALLATION CHECKLIST Check Blower Safety Screw Check appearance and installation Ensure that blower safety screw is securely tightened. Use a spirit level to check that the hood is level. See page 16, Step 9. If screw is missing, order Review installation instructions to determine source replacement parts bag. of problem. Top covers (if used) should lay flat in the recess on Check Operating Sound and Proper Air-Flow top of the hood. Make sure side tab
Summary of the content on the page No. 20
Note: While performing installations described in this book, safety glasses or goggles should be worn. ® For Monogram local service in your area, call 1.800.444.1845. Note: Product improvement is a continuing endeavor at General Electric. Therefore, materials, appearance and specifications are subject to change without notice. GE Consumer & Industrial Appliances General Electric Company Louisville, KY 40225 Pub. No. 49-80209-3 ge.com 01-08 JR
