Summary of the content on the page No. 1
OWNER’S MANUAL
MANUALLY TUNED SYNTHESIZER STEREO RADIO
WITH COMPACT DISC PLAYER DIGITAL
Summary of the content on the page No. 2
CONTENTS Installation .....................................................................................................3 DIN Front-Mount (Method A) ..................................................................................3 Installing the unit...............................................................................................3 Removing the unit .............................................................................................4 DIN Rear-Mount (Method B) .........
Summary of the content on the page No. 3
INSTALLATION Notes: • Choose the mounting location where the unit will not interfere with the normal driving function of the driver. • Before finally installing the unit, connect the wiring temporarily and make sure it is all connected up properly and the unit and the system work properly. • Use only the parts included with the unit to ensure proper installation. The use of unauthorized parts can cause malfunctions. • Consult with your nearest dealer if installation requires the drilling of hol
Summary of the content on the page No. 4
1. Dashboard 1 2. Nut (5mm) 6 3. Spring washer 7 4 4. Screw (5 x 25mm) 5 2 5. Screw 3 6. Strap Be sure to use the strap to secure the back of the unit in place. The strap can be bent by hand to the desired angle. (Fig. 2) 7. Plain washer Removing the unit 1. Frame 1 2. Insert fingers into the groove in the front of frame and pull out to remove the frame. (When re-attaching the frame, point the side with a groove downwards and attach 2 it.) 3 3. Lever Insert the levers supplied with the unit int
Summary of the content on the page No. 5
HOW TO REMOVE AND INSTALL THE FRONT PANEL (OPTIONAL) 1. Press the release button and pull-off the front panel. Keep front panel into the case. 2. To install the front panel, insert the panel into the housing and make sure the panel is properly installed, otherwise, abnormalities occurs on the display or some keys will not function properly. REMOVING THE FRONT PANEL Front Panel Release Button INSTALLING THE FRONT PANEL 5
Summary of the content on the page No. 6
WIRING CONNECTION FOR 2 X 7W SYSTEM CD CHANGER CONNECTOR SOCKET MAIN UNIT (FOR CD CHANGER VERSION ONLY) ANTENNA CONNECTOR (GREY) RCA CABLE Rch RED CHOKE BOX MEMORY YELLOW Lch WHITE BACK-UP BLACK (FOR RCA LINE OUT VERSION ONLY) GROUND (B–) FUSE BLUE RED POWER IGNITION ANTENNA SWITCH (B+) (FOR POWER ANT. VERSION ONLY) WHITE GREY + + Rch Lch SPEAKER SPEAKER – WHITE/BLACK GREY/BLACK – WIRING CONNECTION FOR 4 X 7W OR 2 X 25W SYSTEM CD CHANGER CONNECTOR SOCKET MAIN UNIT (FOR CD CHANGER VERSION ONLY) A
Summary of the content on the page No. 7
OPERATION 4 17 18 16 20 7 9 15 1 2 5 19 3 6 14 12 8 13 10 11 22 21 GENERAL OPERATION • ON/OFF Press PWR button (1) to turn on the unit. Press it again to turn it off. • FACEPLATE RELEASE Press REL button (2) to detach the removable faceplate. • LOUDNESS Press LOU/RND button (8) shortly to reinforce the bass output. 7
Summary of the content on the page No. 8
• SET THE CLOCK Press DSP button (9) to change the display to clock display. Press it again to return to previous display. In clock display, press and hold the DSP button (9) for several seconds until the clock display flashes. Press VOL (5) to change minutes or VOL (4) to change hours. • SELECT MODE Press SEL button (3) to change audio mode through volume, bass, treble, balance, and fader modes. Use VOL (4) and VOL (5) buttons to adjust the selected mode. When mode has not been adjuste
Summary of the content on the page No. 9
• FLASHING LED If the front panel is not on the main unit, LED (21) will be flashing. • RESET BUTTON FUNCTION RESET button (22) is placed on the housing and must be activated with either a ballpoint pen or thin metal object. The RESET button (22) is to be activated for the following reasons: - Initial installation of the unit when all wiring is completed. - All the function buttons do not operate. - Error symbol on the display. Note: If press RESET button (22), the unit can’t work yet, please
Summary of the content on the page No. 10
RADIO OPERATION • BAND Press BND button (10) to change bands as below: FM MW LW • SELECT STATION Rotate TUNING knob (11) clockwise or anticlockwise to adjust the frequency upward or downward. • LOCAL/DISTANT Press the LOC/RPT button (12) to select between local setting for reception of strong station and distant setting for reception of weak stations when tuning. • MONO/STEREO In FM band, press MON/INT button (13) to select mono or stereo reception for radio stations. You can sometimes impro
Summary of the content on the page No. 11
CD OPERATION • DISC PLAY Gently insert a compact disc with the label side facing up into the disc slot (16). The disc is then automatically loaded into the unit and starts playing with the first track of the disc. The digital display will indicate the track number and the time of the track. • EJECT Press (eject) button (15) to stop CD play and eject CD from slot. Receiver switches to radio operation. • PAUSE CD During CD playing, press button (14) to temporarily stop playing. Press it agai
Summary of the content on the page No. 12
SPECIFICATION GENERAL Power Supply Requirements : DC 12 Volts, Negative Ground Chassis Dimensions : 178 (W) x 163 (D) x 50 (H) mm Tone Controls - Bass (at 100 Hz) : +10 dB / –10 dB - Treble (at 10 KHz) : +10 dB / –10 dB Maximum Output Power - Version V : 7W x 4 (ch) or 25W x 2 (ch) - Low Power Version : 7W x 2 (ch) Current Drain - Version V : 5 Ampere (FOR NORMAL POWER) - Low Power Version : 3 Ampere (FOR LOW POWER) CD PLAYER Signal to Noise Ratio : More than 60 dB Channel Separation : More than
Summary of the content on the page No. 13
TROUBLE SHOOTING Before going through the check list, check wiring connection. If any of the problems persist after check list has been made, consult your nearest service dealer. Symptom Cause Solution No power. The car ignition switch is If the power supply is properly not on. connected to the car accessory terminal, switch the ignition key to “ACC”. The fuse is blown. Replace the fuse. Disc cannot be Presence of CD disc inside Remove the disc in the player, loaded or ejected. the player. then
