Summary of the content on the page No. 1
Use andCare & Installation Guide
Downdraft Vent System
Problem Solver .................................4
Safety Instructions .........................2
More questions ?…call
GE Answer Center® 800.626.2000
Operating Instructions, Tips
Canning.............................................................3
Installation.....................................5–11
Controls.............................................................3
Ductwork Table...............................................8
Cooking
Summary of the content on the page No. 2
IMPORTANT SAFETY INSTRUCTIONS Read and save these instructions. WARNING—TO REDUCE THE RISK OF D. Use an extinguisher ONLY if: FIRE, ELECTRIC SHOCK, OR INJURY TO 1. You know you have Class ABC extinguisher, PERSONS, OBSERVE THE FOLLOWING: and you already know how to operate it. A. Use this unit only in the manner intended by the 2. The fire is small and contained in the area manufacturer. If you have questions, contact the where it started. manufacturer. 3. The fire department is being called. B.
Summary of the content on the page No. 3
Safety Instructions Servicing Using Vent System Cooking Tips SERVICING NOTE: BE SURE ELECTRICAL POWER IS Disconnect power to the cooktop and remove it first. OFF BEFORE SERVICING THE UNIT. Reverse the steps in the Install the Downdraft section to remove the downdraft from the cabinet. It may be necessary to remove the downdraft blower system from the cabinet in order to service components Service parts are available from your local GE such as the blower motor or air vent mechanism. distributor o
Summary of the content on the page No. 4
CARE AND CLEANING Grease Filter The efficiency of your downdraft depends on a clean filter. Frequency of cleaning depends on the type of cooking you do. Grease filters should be cleaned at least once a month. Never operate the downdraft without the filters in place. To remove: Pull the filters out by grasping them and pulling straight up. To clean: Soak and then agitate in a hot detergent solution. Light brushing may be used to remove imbedded soil. Rinse, shake and remove moisture before replac
Summary of the content on the page No. 5
Flat counter area INSTALLATION INSTRUCTIONS Before Starting Installation Check the Take Measurements Following Requirements Refer to the cooktop installation instructions for dimensions of cooktop, countertop cut-out, and This downdraft blower system is designed to be cabinet requirements. used to exhaust smoke and odors when cooking with all GE electric and sealed burner gas • The 30† models will fit in most 30† wide cooktops (not approved for standard burner gas cabinets and the 36† models wil
Summary of the content on the page No. 6
30† COOKTOPS/DOWNDRAFT UNITS JVB34, JVB35, JVB93 1 3 Figure 1 Overall Cooktop Dimensions Figure 3 Cutout for Vent 2 Figure 2 Overall Cutout Dimensions NOTE: AGAINST-THE-WALL INSTALLATIONS ARE LIMITED DUE TO DIMENSION REQUIREMENTS. REFER TO DETAILS BELOW. PLANNING INSTALLATION (Note: 26† deep cabinets required) PREPARING CUTOUT A B C B&C D I E F G H (Figure 1) (Figure 1) (Figure 1) (Figure 1) (Figure 3*) (Figure 2) (Figure 2) (Figure 2) (Figure 3) (Figure 3) Min. Se
Summary of the content on the page No. 7
36† COOKTOPS/DOWNDRAFT UNITS JVB64, JVB65, JVB96 1 3 Figure 1 Overall Cooktop Dimensions Figure 3 Cutout for Vent 2 Figure 2 Overall Cutout Dimensions NOTE: AGAINST-THE-WALL INSTALLATIONS ARE LIMITED DUE TO DIMENSION REQUIREMENTS. REFER TO DETAILS BELOW. PLANNING INSTALLATION (Note: 26† deep cabinets required) PREPARING CUTOUT A B C B&C D I E F G H (Figure 1) (Figure 1) (Figure 1) (Figure 1) (Figure 3*) (Figure 2) (Figure 2) (Figure 2) (Figure 3) (Figure 3) Min. Se
Summary of the content on the page No. 8
INSTALLATION INSTRUCTIONS (continued) Plan the Ductwork Steps to Determine Flexible Ducting’s Equivalent Length 1. Measure the actual amount of offset (Maximum 3† recommended). The effect upon Right airflow is dependent upon the amount of offset. discharge 2. Calculate the equivalent ducting allowances Left discharge using: ( ___ in. offset) x (14 Ft. per inch) Down discharge = ___ Ft. equivalent length. (as shipped) 3. Ensure that the total equivalent length of ducting does not exceed the max
Summary of the content on the page No. 9
Plan the Wiring LEFT OR RIGHT DISCHARGE Blower 1. The downdraft blower system draws 4 AMPS Nut and requires a 120 VAC, 60 Hz circuit. Motor plug 2. The unit has a 2 ft. long power cord with a 3-pronged plug. Plan to provide a grounded outlet in a location which will allow the unit’s Clamp Sheet power cord to reach. The outlet cannot be channel metal located on a back wall. The outlet needs to be screw mounted on the side wall of the cabinet or it could be on the back wall of an adjacent cabine
Summary of the content on the page No. 10
INSTALLATION INSTRUCTIONS (continued) Install the Downdraft Install the Ductwork CAUTION- BEFORE CUTTING A HOLE Mounting screws IN CABINET FOR DUCTWORK: Check for interference with floor joists, wall studs, Leveling bracket– electrical wiring or plumbing. flange facing out 31⁄4† x 10† to 6† RD. Transition Leveling bracket– flange facing in Blower Collar 6† RD. Screws Elbow & ductwork 1. Set the downdraft into the opening. Extend the leveling brackets to the floor of the cabinet so the downdraft
Summary of the content on the page No. 11
Install the Cooktop Adjust the Switch 1. Align the cooktop with the downdraft and The downdraft is factory-adjusted for proper fasten cooktop in place. operation. However, shipping and handling may affect the positions of the activating switch. NOTE: Accurate alignment of cooktop and downdraft is necessary to ensure that there is To adjust position of activating switch: not interference when air vent is raised and lowered. There should be a gap of 1/32† –1/16† WARNING: To avoid possible electric
Summary of the content on the page No. 12
Staple sales slip or cancelled check YOUR DOWNDRAFT SYSTEM here. Proof of original purchase date WARRANTY is needed to obtain service under warranty. FULL ONE-YEAR WARRANTY This warranty is extended to WHAT IS COVERED the original purchaser and any For one year from date of original succeeding owner for products purchase, we will provide, free of purchased for ordinary home use in charge, parts and service labor in the 48 mainland states, Hawaii and your home to repair or replace Washington,
