Summary of the content on the page No. 1
MA NUAL T R AN S M ISS ION MULT I-C H A NNEL R EMOT E
S T AR TE R AN D F U L L - F E A T UR ED A L AR M S Y S T E M
CT-5060
User Guide
Introduction......................................... 1 Remote Door Locks...................... 6
Basic Remote Operation..................... 1 Passive or Active Arming.............. 7
Remote-starting Your Vehicle............. 2 Disarmed Notification.................... 7
Remote-starting ............................ 2 Shock Sense And Warn-Away
Sense....
Summary of the content on the page No. 2
Note: Pressing the LOCK and UNLOCK buttons at the same time will activate the AUX 2 output. Remote-starting Your Vehicle Remote-starting Press the START/STOP button for approx. 1 second. The parking lights will come ON, informing you that the unit has received your signal. The engine will start approx. 5 seconds later. The parking lights will remain ON during the pre-programmed run time. If the vehicle doesn’t start at the first attempt, the system will shut down, wait a few seconds,
Summary of the content on the page No. 3
• Door opened; • Hood opened; • Brakes pressed; • Parking Brake disengaged; • Key turned to the IGNITION ON (RUN) position. Should any of the above occur, Ready Mode will be cancelled. Note: The unit will notify the user that it has exited Ready Mode by giving three slow flashes of the vehicle’s Parking Lights. Vehicle Presets Heater & Heated Seat When leaving the vehicle it is recommended to preset the accessory controls in preparation for the next remote start. Settings for the bl
Summary of the content on the page No. 4
Valet Mode The system can be placed in Valet Mode to disable the remote starting capabilities. If the vehicle needs to be serviced, or if you park it indoors, the Valet Mode will prevent the engine from being remote-started accidentally. To put the system into Valet Mode: 1. Turn the key to the IGNITION ON (RUN) position. 2. Within 3 sec. press the Valet button and release it. The LED will come ON. (The system is in Valet Mode.) To take the system out of Valet Mode: 1. Turn the key to
Summary of the content on the page No. 5
In an emergency situation, you can activate Panic Mode using the LOCK or UNLOCK button. This will: • Shut down the engine, • Disarm the Starter Kill and • Unlock the doors (if UNLOCK is • Activate the siren for 1 minute. pressed) (See below for a description of the Starter • Or lock the door (if LOCK is Kill.) pressed), To activate Panic Mode • Press and hold the UNLOCK button for approximately 3 seconds until the siren starts to sound and the parking lights flash: this will unloc
Summary of the content on the page No. 6
Priority Door Access This safety feature lets you unlock only the driver’s door when you press the UNLOCK button on the transmitter, and then UNLOCK the rest of the vehicle doors if the UNLOCK button is pressed for a second time within 3 seconds. Chirp Delete To temporarily disable the siren’s chirp confirmations upon arming and disarming (e.g. in a quiet neighbourhood): 1. Press the TRUNK button. 2. Within 3 seconds, press the LOCK or UNLOCK button to arm or disarm without any chirp
Summary of the content on the page No. 7
Passive or Active Arming By default, the system is configured to Passive Arming Mode. In Passive Arming Mode, the Starter Kill and the Alarm will automatically arm 30 seconds after the last door is closed. The system will not arm itself if a door is left open. Important note: When the system re-arms automatically or if there is an Alarm condition, you can disarm the system by simply pressing the UNLOCK button. Disarmed Notification This feature will notify the user when the vehicle was
Summary of the content on the page No. 8
Ignition Re-Lock When the Ignition-Controlled Door Locks option is enabled and the ignition is ON, should any door be unlocked and opened, all the doors will be re-locked next time the brake pedal is pressed. Secure Lock This is an added security feature. If your system was installed with the Secure Lock option, it will automatically lock your doors and arm the system 4 seconds after your start your car by remote. The system will automatically lock the doors again after shut-down. Remo
Summary of the content on the page No. 9
Car Finder When enabled, the Car Finder option will help you locate your vehicle by sending a pulsating signal through the horn or the siren. To hear the signal, press the LOCK and UNLOCK buttons simultaneously. This will produce a pulsating signal for the time you keep the buttons pressed. Diagnostics – Chirps Diagnostics – Parking Lights Chirps Description • Lock and arm the system. • Lock confirmation. 1 • Entering Mode 1 in the programming options. • Start attempt when engine
Summary of the content on the page No. 10
• Entering Cold Weather Mode • Exit Ready Mode 3 • Enter Remote Valet • Enter ignition valet • +12 volts detected on the Brake line; cranking cancelled 4 • Entering Tach Learning • New Transmitter learnt 5 • Tach learnt • Remote start attempt was made with a Tach or a vacuum signal 6 detected before cranking 8 • Unit reset: occurs when the unit is reset to factory defaults 10 • The Hood Switch line went to ground during cranking or run time 1 – pause • There was an attempt to
